MIL-C-26482 Series I Connectors
KPT connectors are a series of general - purpose,
environment - resistant, miniature circular connec-
tors, qualified for use in industrial applications
calling for quick - disconnect connectors with fixed
contacts
for
solder
termination.
These miniature circular connectors are grouped
into two series ranging from general purpose solder
pot connectors . . . to high performance, crimp con-
nectors . . . to connectors with high contact densi-
ty. This broad range provides the most complete
family of 26482 connectors available today. The
versatility of these connectors is proven by the
fulfillment of requuirements ranging from general
purpose to space environmental.
KPT/KPSE
In addition to the two basic series, connectors for
special applications are also available. They include
RFI filtering versions (with loss pass internal filter
pin contacts), hermetic connectors for high pres-
sure watertight requirements, and twist - on pull - off
couplers for MIL-C-26482 plugs.
This series is intermateable and intermountable
with all MIL-C-26482 connectors, whether solder
or crimp type and is available with many materials,
finishers and configurations.
Solder
Crimp
• General purpose
• Closed-entry socket contacts
• Solder termination
How to Order - KPT - Solder Contact Connectors
SERIES PREFIX
KPT - ITT Cannon prefix
MS - MIL-C-26482 prefix
SHELL STYLE
Cannon Designation
00 - wall mounting receptacle
01 - cable connecting plug
02 - box mounting receptacle (Class E only)
*
03 - wall mounting receptacle without grom-
met, ferrule and endbell
*
04 - cable connecting plug without grommet,
ferrule and endbell
05 - straight plug withoug grommet, ferrule,
*
and endbell
06 - straight plug
07 - jam nut receptacle (available in hermetic
version also)
08 - 90˚ angle plug
B - thru-bulkhead receptacle (Class E only)
MS 3110 E 22 - 36 P Y
KPT 00 E 22 - 36 P Y
SERIES PREFIX
SHELL STYLE
CLASS
SHELL SIZE
CONTACT ARRANGEMENT
CONTACT STYLE
ALTERNATE INSERT POSITION
MODIFICATION CODE
CLASS
A - general duty (not MS approved)
B - general duty with strain relief without
grommet & ferrules (may be used for pot-
ting when strain relief is desired) (not MS
approved)
E - grommet seal except on 02 and 3112 (MS
specification)
F - grommet seal with strain relief (MS specifi-
cation)
J - water tight gland seal with strain relief for
jacketed cable (MS specification)
P - potted (MS specification)
SHELL SIZE
8, 10, 12, 14, 16, 18, 20, 22, and 24
CONTACT ARRANGEMENT
See contact arrangement page 149.
CONTACT STYLE
P - pin; S - socket
ALTERNATE INSERT POSITION
W, X, Y and Z. (Omit for normal.)
MODIFICATION CODE
Omit first (0) of shell style indication when using
modifications code.
07 - clear chromate over cadmium
16 - twist-pull lanyard release coupler (appli
cable to plug only).
23 - grounding springs fingers (applicable to
plug only)
**
*
Consult factory for details
SHELL STYLE (cont'd)
MS Designation
3110 - wall mounting receptacle
3111 - cable connecting plug
3112 - box mounting receptacle (Class E only)
3114 - jam nut receptacle
3116 - straight plug
3119 - thru-bulkhead receptacle (Class E only)
How to Order - KPTB Thru-Bulkhead Receptacle Connectors
• General Purpose
• Double ended pin and socket contacts
• Contains KPT socket insert
• Nonremovable contacts
KPT connectors are a series of general - purpose,
miniature circular connectors, qualified for use in
military applications. Ther are also widely used in
industrial applications. The KPTB in a thru-bulkhead
version with double faced pin and socket insert
construction allowing mating from both ends. They
contain KPT socket inserts with feed-thru (pin/
socket) non-removable contacts.
KPTB 22 - 55 PS Y
SERIES PREFIX
SHELL SIZE
CONTACT ARRANGEMENT
CONTACT STYLE (pin & socket)
ALTERNATE INSERT POSITION
MIL-C-26482 PREFIX
CLASS
SHELL SIZE
CONTACT ARRANGEMENT
ALTERNATE INSERT POSITION
The thru-bulkhead receptacle is provided for appli-
cations requiring the disconnnection of a power
source from either side of a panel. A typical
connector to be used if air leakage requirements
are critical.
MS3119 E
22 - 55 Y
Dimensions are shown in inches (millimeters).
Dimensions subject to change.
www.ittcannon.com
140
MIL-C-26482 Series I Connectors
How to Order - KPSE Crimp Contact Connectors
KPT/KPSE
MS
3120 E 18 - 32 P
KPSE 00 E 18 - 32 P
SERIES PREFIX
SHELL STYLE
CLASS
SHELL SIZE
CONTACT ARRANGEMENT
CONTACT TYPE
ALTERNTE INSERT POSITION
MODIFICATION CODE
SERIES PREFIX
KPSE - ITT Cannon prefix
MS - MIL-C-26482 prefix
SHELL STYLE
ITT Cannon Number:
00 - wall mounting receptacle
01 - cable connecting plug
02 - box mounting receptacle (without wire
seals)
03 - wall mounting receptacle without ferrule
*
and endbell
04 - cable connector plug without ferrule and
*
endbell
05 - straight plug without ferrule and endbell
*
06 - straight plug
07 - jam nut receptacle
08 - 90˚ angle plug
MS Desgination
3120 - wall mounting receptacle
3121 - cable connnecting plug
3122 - box mounting receptacle
3124 - jam nut receptacle
3126 - straight plug
CLASS
A - general duty (not MS approved)
B - general duty with strain relief without
grommet & ferrules (not MS approved)
E - grommet seal (MSspecification)
F - grommet seal with strain relief (MS specifi-
cation)
J - gland seal with strain relief for jacketed
cable (not MS approved)
P - potted (MS specification)
SHELL SIZE
10, 12, 14, 16, 18, 20, 22, and 24
CONTACT ARRANGEMENT
See contact arrangements page 149.
CONTACT STYLE
P - pin
S - socket
ALTERNATE INSERT POSITION
W, X, Y and Z. (Omit for normal.)
X
X
**
MODIFICATION CODE
Omit first (0) of shell style indication when using
modifications code.
F0 - less contacts, not marked on connectors
07 - clear chromate over cadmium
16 - twist-pull lanyard release coupler (appli
cable to plug only).
23 - grounding springs fingers (applicable to
plug only)
*
Consult factory for details
KPSE High Performance Crimp Contact Connectors
Environment -resistant
Voidless integrally molded insulator
Front-release, crimp snap-in contacts
Closed entry socket contacts
4 moisture seals for complete sealing
Contact clip protected in hard dieletric
Positive insert-to-shell mechanical retention
KPSE environment-resistant, miniature circular,
quick
disconnect
connectors,
qualified
to
MIL-C-26482, are designed for the exacting re-
quirements of today's electronic industry. The KPSE
features an insulator which is mechanically retained
in the shell by a positive, hard plastic-to-metal lock
retention augmented by a reliable adhesive bond.
Complete moisture sealing is achieved by four
seal; shell, peripheral, interfiacial and wire seals.
Crimp snap-in contacts are retained in clips that are
completely encased in a tough hard dieletric wafer,
thus protecting the clips tines from damage. Closed-
entry socket contacts facilitate positive mating.
The KPSE series is intermateable, intermountable
and interchangeable with all MIL-C-26482 connec-
tors, whether crimp or solder type, and is avialiable
with many materials, finishes and configurations.
STANDARD MIL-C-26482 HARDWARE
MIL-C-26482.
mates with any connector designed to
CRIMP, SNAP-IN CONTACTS
are designed to MIL-C-39029 and can be crimped
with the standard M22520/1 crimp tool.
CLOSED-ENTRY SOCKET CONTACTS eliminate damage from abuse by test
probes and help to correct any misaligned pins during engagement.
CONTACT INSERTION is accomplishted from the rear of the connector.
When the contact is fully inserted, the clip tines snap securely behind
the contact shoulder.
CONTACT EXTRACTION is accomplished with a front-inserted extraction
tool. Pressing the tool plunger pushes the contact out thru the rear of
the connnector.
CONTACT RETAINING CLIP
is completely encased in a tough plastic wafer to
protect the clip from damage.
COMPLETE MOISTURE SEALING
is achieved by combining four seals: shell,
peripheral, interfacial and wire seals.
SHELL SEAL is effected when the plug shell pushes against the sealing
ring in the receptacle when the connectors are mated.
PERIPHERAL SEAL around the edge of the pin insulator is designed so
that mating the connector puts tension on the seal and greatly reduces
compression set.
INTERFACIAL SEAL is achieved by the insulator faces meeting when the
plug and receptacle are mated.
WIRE SEAL is accomplished by a mulitiple ripple design, exceeding the
wire sealing requirements of MIL-C-26482.
POSITIVE INSERT-TO-SHELL MECHANICAL RETENTION
with hard plastic wafer
firmly locked into a groove in the shell, in addition to a strong adhesive
bond between the insert and shell.
Dimensions are shown in inches (millimeters).
Dimensions subject to change.
www.ittcannon.com
141
MIL-C-26482, Series I Connectors
Performance and Material Specifications
STANDARD MATERIALS AND FINISHES
Shell
aluminum alloy, conductive
olive drab chromate over
cadmium finish per QQ-P-416
polychloroprene
polychloroprene
Copper alloy, gold plate
per MIL-G-45204 type II
- 55˚C to +125˚C
KPT/KPSE
MECHANICAL
Shell Sizes 00 - wall mounting receptacle
01 - cable connecting plug
02 - box mounting receptacle
06 - straight plut
07 - jam nut receptacle
08 - 90˚ angle plug
B - thru-bulkhead receptacle
(KPT only)
Shell Sizes
KPT 8 thru 24
KPSE 10 thru 24
Insulator
Grommet and Seal
Contacts
Temperature Range
Polarization/Coupling: five keyway/three point bayonet
Service Classes A - general duty
B - general duty with strain relief
E - grommet seal
F - grommet seal with strain relief
J - gland nut with strain relief for jacketed cable
P - potted
ELECTRICAL
Contact Termination
Number of contacts
Wire size, AWG
Wire Range Accommodations
Contact
Size
20
16
12
Contact
Rating
AWG Wire Size
24, 22 and 20
20, 18 and 16
14 and 12
Contact
Size
20
16
Service
Rating
Test Volt
Sea level
Rated
Amps
7.5
22.0
Service
1
2
70,000 ft.
Maximum
Operating
Voltage
1
2
Sea level
1
2
AC(rms)
1500
2300
375
550
600
1000
Min. KPT
.060 (1.52)
.066 (1.68)
.097 (2.46)
Test
Current
7.5
13.0
DC
2100
3200
535
770
850
1275
solder (KPT)
KPT 2 thru 61
KPT 12 thru 24
crimp snap-in (KPSE)
KPSE 3 thru 61
KPSE 16 thru 24
Insulation O.D. Limits
Min.
KPSE
.047 (1.19)
.066 (1.68)
Max. KPT/
KPSE
.083 (2.11)
.109 (2.77)
.142 (3.61)
Millivolt Drop
less than 55
less than 50
Dimensions are shown in inches (millimeters).
Dimensions subject to change.
www.ittcannon.com
142
MIL-C-26482, Series I Connectors
Wall Mounting Receptacles
MS3110 (MS service class E, F, J, P)
MS3120 (MS service class E, F, P)
KPT00
KPSE00
SEE TERMINATION
ASSEMBLY
M
Q THD.
SEE TERMINATION
ASSEMBLY
K
Q THD.
M
KPT/KPSE
POLARIZING
GROOVE
GROMMET
FOR
TYPES
E&F
T DIA.
4 MTG.
HOLES
A
DIA.
A
DIA.
K
SOLDER
KPT00/MS3110
M
+ .031 (+.79)
-.000 (-.00)
.431 (10.95)
.431 (10.95)
.431 (10.95)
.431 (10.95)
.431 (10.95)
.431 (10.95)
.556 (14.12)
.556 (14.12)
.589 (14.96)
GROMMET FOR
TYPES A, B, J & P
CRIMP
KPSE00/MS3120
R (TP)
S
.140 RAD.
MAX.
RECEPTACLE ASSEMBLY
Shell
Size
8
10
12
14
16
18
20
22
24
A
+ .003 (+.08)
_
_
.471 (11.96)
.588 (14.96)
.748 (19.00)
.873 (22.17)
.998 (25.35)
1.123 (28.52)
1.248 (31.70)
1.373 (34.87)
1.498 (38.05)
K
+ .016 (+.41)
_
_
.062 (1.57)
.062 (1.57)
.062 (1.57)
.062 (1.57)
.062 (1.57)
.062 (1.57)
.094 (2.39)
.094 (2.39)
.094 (2.39)
R*
(TP)
.594 (15.09)
.719 (18.26)
.812 (20.62)
.906 (23.01)
.969 (24.61)
1.062 (26.97)
1.156 (29.36)
1.250 (31.75)
1.375 (34.92)
S
Max.
.828 (21.03)
.954 (24.23)
1.047 (26.59)
1.141 (28.98)
1.234 (31.34)
1.328 (33.73)
1.453 (36.91)
1.578 (40.08)
1.703 (43.26)
T
_
- .005 (+.13)
_
.120 (3.05)
.120 (3.05)
.120 (3.05)
.120 (3.05)
.120 (3.05)
.120 (3.05)
.120 (3.05)
.120 (3.05)
.147 (3.73)
Q Thread
Class 2A
7/16-28UNEF
9/16-24UNEF
11/16-24UNEF
13/16-20UNEF
15/16-20UNEF
1-1/16-18UNEF
1-3/16-18UNEF
1-5/16-18UNEF
1-7/16-18UNEF
Not available in KPSE *(TP) located within .010 T.P. with respect to diameter A and master keyway.
Receptacles with Termination Assemblies
LA
V THD
LBF
LE
LJ
LP
DA
.395
(10.03)
MIN.
TYPE A
TYPE B AND F
BE
GBF
HBF
DJ
HJ
BP
DP
TYPE E
TYPE J
TYPE P
TYPE A
Shell
Size
†8
10
12
14
16
18
20
22
24
DA
Min.
.335 (8.15)
.466 (11.84)
LA
Max.
1.44 (36.68)
1.44 (36.68)
V Thread
Class 2A
1/2-28UNEF
5/8-24UNEF
3/4-20UNEF
7/8-20UNEF
1-20UNEF
1-3/16-18UNEF
1-3/16-18UNEF
1-7/16-18UNEF
1-7/16-18UNEF
TYPE J
Shell
Size
†8
10
12
14
16
18
DJ
Max./Min.
.230/.168 (5.84/4.27)
.312/.205 (7.92/5.21)
.442/.338 (11.23/8.59)
.539/.416 (13.56/10.57)
.616/.550 (15.65/13.97)
.672/.600 (17.07/15.24)
.747/.634 (18.97/16.13)
.846/.670 (21.49/17.02)
.894/.740 (22.71/18.80)
HJ
Max.
.828 (21.03)
.891 (22.63)
1.016 (25.81)
1.141 (28.98)
1.203 (30.56)
1.469 (37.31)
1.469 (37.31)
1.656 (42.06)
1.750 (44.45)
GBF
Min.
.115 (2.92)
.178 (4.52)
.302 (7.67)
.365 (9.27)
.490 (12.45)
.615 (15.62)
.615 (15.62)
.740 (18.80)
.790 (20.07)
TYPE B and F
HBF
Max.
LBF
Max.
BE
Max.
TYPE E
LE
Max.
1.328 (33.73)
1.328 (33.73)
1.328 (33.73)
1.328 (33.73)
1.328 (33.73)
1.328 (33.73)
1.531 (38.89)
1.531 (38.89)
1.594 (40.49)
.828 (21.03) 1.922 (48.82)
.891 (22.63) 1.922 (48.82)
1.016 (25.81) 1.922 (48.82)
1.141 (28.98) 1.922 (48.82)
.608 (15.44)
.734 (18.64)
.858 (21.79)
.984 (24.99)
.591 (15.01) 1.444 (36.68)
.705 (19.05) 1.444 (36.68)
.830 (21.08) 1.444 (36.68)
.948 (24.08) 1.444 (36.68)
1.043 (26.49) 1.728 (43.89)
1.198 (30.43) 1.728 (43.89)
1.293 (32.84) 1.738 (44.15)
1.203 (30.56) 2.047 (51.99) 1.110 (28.19)
1.469 (37.31) 2.078 (52.78) 1.234 (31.34)
1.469 (37.31) 2.344 (59.54) 1.360 (34.54)
1.656 (42.06) 1.344 (59.54) 1.484 (37.69)
1.750 (44.45) 2.406 (61.11) 1.610 (40.89)
TYPE P
LJ
Max.
2.271 (57.68)
2.271 (57.68)
2.411 (61.24)
2.599 (66.01)
2.943 (74.75)
3.172 (80.57)
3.610 (91.69)
3.766 (95.66)
3.985 (101.22)
BP
Max.
.608 (15.44)
.734 (18.64)
.858 (21.79)
.984 (24.99)
1.110 (28.19)
1.234 (31.34)
1.360 (34.54)
1.484 (37.69)
1.610 (40.89)
DP
Min.
.317 (8.05)
.434 (11.02)
.548 (13.92)
.673 (17.09)
.798 (20.27)
.899 (22.83)
1.024 (26.01)
1.149 (29.18)
1.274 (32.36)
LP
Max.
1.453 (36.91)
1.453 (36.91)
1.453 (36.91)
1.453 (36.91)
1.453 (36.91)
1.453 (36.91)
1.672 (42.47)
1.672 (42.47)
1.734 (44.04)
Performance Specifications - Page 142
Contacts, Sealing Plugs, Assembly Tools - Page
154
Contact Arrangements - Page 149
20
22
24
†Not available in KPSE
Dimensions are shown in inches (millimeters).
Dimensions subject to change.
www.ittcannon.com
143
MIL-C-26482, Series I Connectors
Cable Connecting Plugs
MS3111
(MS service class E, F, J, P)
MS3121
(MS service clase E, F, P)
KPT01
KPSE01
H
P
Q THD.
A
DIA.
SEE TERMINATION
ASSEMBLY
SEE TERMINATION
ASSEMBLY
H
P
Q THD.
Y DIA.
KPT/KPSE
POLARIZING
GROOVE
A
DIA.
GROMMET FOR
TYPES A, B, J & P
SOLDER
KPT01/MS3111
GROMMET FOR
TYPES E & F
CRIMP
KPSE01/MS3121
P
+ .031 (+.79)
-.000 (-.00)
.400 (10.16)
.400 (10.16)
.400 (10.16)
.400 (10.16)
.400 (10.16)
.400 (10.16)
.535 (13.59)
.535 (13.59)
.558 (14.43)
S
PLUG ASSEMBLY
Shell
Size
†8
10
12
14
16
18
20
22
24
A
+ .003 (+.08)
_
_
.471 (11.96)
.588 (14.94)
.748 (19.00)
.873 (22.17)
.998 (25.35)
1.123 (28.52)
1.248 (31.70)
1.373 (34.87)
1.498 (38.05)
H
+ .016 (+.41)
_
_
.094 (2.39)
.094 (2.39)
.094 (2.39)
.094 (2.39)
.094 (2.39)
.094 (2.39)
.115 (2.92)
.115 (2.92)
.115 (2.92)
S
Max.
.828 (21.03)
.954 (24.23)
1.047 (26.59)
1.141 (28.98)
1.234 (31.34)
1.328 (33.73)
1.453 (36.91)
1.578 (40.08)
1.703 (43.26)
Y
Max.
.958 (24.33)
1.082 (27.48)
1.176 (29.87)
1.270 (32.26)
1.364 (34.65)
1.458 (37.03)
1.582 (40.18)
1.708 (43.38)
1.832 (46.53)
Q Thread
Class 2A
7/16-28UNEF
9/16-24UNEF
11/16-24UNEF
13/16-20UNEF
15/16-20UNEF
1-1/16-18UNEF
1-3/16-18UNEF
1-5/16-18UNEF
1-7/16-18UNEF
†Not available in KPSE *(TP) located within .010T.P. with respect to diameters A and master keyway.
Cable Connecting Plugs With Termination Assemblies
LA
V THD
LBF
LE
LJ
LP
DA
.395
(10.03)
MIN.
TYPE A
TYPE B AND F
BE
GBF
HBF
DJ
HJ
BP
DP
TYPE E
TYPE J
TYPE P
With Termination Assemblies
TYPE A
Shell
Size
†8
10
12
14
16
18
20
22
24
DA
Min.
.335 (8.15)
.466 (11.84)
.591 (15.01)
.705 (19.05)
.830 (21.08)
.948 (24.08)
1.043 (26.49)
1.198 (30.43)
1.293 (32.84)
LA
Max.
1.44 (36.68)
1.44 (36.68)
1.44 (36.68)
1.44 (36.68)
1.44 (36.68)
V Thread
Class 2A
1/2-28UNEF
5/8-24UNEF
3/4-20UNEF
7/8-20UNEF
GBF
Min.
.115 (2.92)
.178 (4.52)
.302 (7.67)
.365 (9.27)
TYPE B and F
HBF
Max.
LBF
Max.
BE
Max.
TYPE E
LE
Max.
.828 (21.03) 1.922 (48.82)
.891 (22.63) 1.922 (48.82)
1.016 (25.81) 1.922 (48.82)
1.141 (28.98) 1.922 (48.82)
1.203 (30.56) 2.047 (51.99)
.608 (15.44) 1.328 (33.73)
.734 (18.64) 1.328 (33.73)
.858 (21.79) 1.328 (33.73)
.984 (24.99) 1.328 (33.73)
1.110 (28.19) 1.328 (33.73)
1-20UNEF .490 (12.45)
1.44 (36.68) 1-3/16-18UNEF .615 (15.62)
1.728 (43.89) 1-3/16-18UNEF .615 (15.62)
1.728 (43.89) 1-7/16-18UNEF .740 (18.80)
1.738 (44.15) 1-7/16-18UNEF .790 (20.07)
TYPE J
1.469 (37.31) 2.078 (52.78) 1.234 (31.34) 1.328 (33.73)
1.469 (37.31) 2.344 (59.54) 1.360 (34.54) 1.531 (38.89)
1.656 (42.06) 1.344 (59.54) 1.484 (37.69) 1.531 (38.89)
1.750 (44.45)
2.406 (61.11) 1.610 (40.89) 1.594 (40.49)
TYPE P
Shell
Size
†8
10
12
14
16
18
DJ
Max./Min.
.230/.168 (5.84/4.27)
.312/.205 (7.92/5.21)
.442/.338 (11.23/8.59)
.539/.416 (13.56/10.57)
.616/.550 (15.65/13.97)
.672/.600 (17.07/15.24)
.747/.634 (18.97/16.13)
.846/.670 (21.49/17.02)
.894/.740 (22.71/18.80)
HJ
Max.
.828 (21.03)
.891 (22.63)
1.016 (25.81)
1.141 (28.98)
1.203 (30.56)
1.469 (37.31)
1.469 (37.31)
1.656 (42.06)
1.750 (44.45)
LJ
Max.
2.271 (57.68)
2.271 (57.68)
2.411 (61.24)
2.599 (66.01)
2.943 (74.75)
3.172 (80.57)
3.610 (91.69)
3.766 (95.66)
3.985 (101.22)
BP
Max.
.608 (15.44)
.734 (18.64)
.858 (21.79)
.984 (24.99)
1.110 (28.19)
1.234 (31.34)
1.360 (34.54)
1.484 (37.69)
1.610 (40.89)
DP
Min.
.317 (8.05)
.434 (11.02)
.548 (13.92)
.673 (17.09)
.798 (20.27)
.899 (22.83)
1.024 (26.01)
1.149 (29.18)
1.274 (32.36)
LP
Max.
1.453 (36.91)
1.453 (36.91)
1.453 (36.91)
1.453 (36.91)
1.453 (36.91)
1.453 (36.91)
1.672 (42.47)
1.672 (42.47)
1.734 (44.04)
Performance Specifications - Page 142
Contacts, Sealing Plugs, Assembly Tools - Page
154
Contact Arrangements - Page 149
20
22
24
†Not available in KPSE
Dimensions are shown in inches (millimeters).
Dimensions subject to change.
www.ittcannon.com
144
Security Electronics
京公网安备 11010802033920号
EEWORLD
