CHIP TYPE TANTALUM SOLID ELECTROLYTIC CAPACITORS
@Resin
molded chip type
@Pb-free
type
@Extended
capacitance
@Low
profile, small-sized and large capacitance
@New
lineup : J case (Refer to next page)
?SPECIFICATIONS
Items
Category
temperature range
Rated Voltage range
Rated Capacitance range
Rated Capacitance tolerance
Leakage current
Dissipation factor
(tane)
-55 to +125C (+85C max. without voltage derating)
4 to 35V
dc
1.0 to 680MF
P20%
(M)
I[0.01CV or 0.5MA Whichever is greater.
I : Leakage current (MA), C : Rated capacitance (MF), V : Rated voltage (V
dc
)
Psize
4V
[10%
6.3 to 16V
[8%
C=1MF
A2, A, B3
[6%
C=1.5 to 10MF
B2, C, D2
[8%
4V
C=15 to 68MF
Dsize
[8%
C=100 to 330MF
[11%
C=1MF
[4%
C=1.5 to 10MF
[6%
6.3 to 35V
C=15 to 68MF
[8%
C=100 to 330MF
[10%
Table1
[value
in No.4
Requirements
(f=120Hz, 20C)(JIS C 5101-1 4.7.)
(After 5 minutes of applying rated voltage at 20C)
(JIS C 5101-1 4.9.)
Characteristics
at high and
low temperature
Damp heat,
steady state
Surge voltage
Resistance to
soldering heat
Endurance
Rated ripple voltage
Failure rate
Standard
(f=120Hz, 20C)(JIS C 5101-1 4.8.)
+85C
+125C
Psize
Within
P15%
Within
P20%
Capacitance
A2, A, B3, B2, C, D2, Dsize
Within
P10%
Within
P15%
change
4V
Psize
[12%
[10%
DF (tanE)
6.3 to 16V
[10%
[8%
C=1MF
A2, A, B3
[8%
[6%
C=1.5 to 10MF
B2, C, D2
[10%
[8%
4V
C=15 to 68MF
Dsize
[10%
[8%
C=100 to 330MF
[13%
[11%
C=1MF
[6%
[4%
C=1.5 to 10MF
[8%
[6%
6.3 to 35V
C=15 to 68MF
[10%
[8%
C=100 to 330MF
[12%
[10%
Table1
[150%
[120%
of the initial limit
of the initial limit
Leakage current
[0.1CV
or 5MA
[0.125CV
or 6.25MA
-
Whichever is greater Whichever is greater
(JIS C 5101-1 4.24.)
The following specifications shall be satisfied when the capacitors are restored to 20C after subjected them at 40C 90 to 95RH for 500 hours.
Capacitance
Within
P20%
Psize
change
Within
P10%
A2, A, B3, B2, C, D2, Dsize
DF (tanE)
[150%
of the Initial specified value
Psize
[The
Initial specified value
A2, A, B3, B2, C, D2, Dsize
(JIS C 5101-1 4.22.)
Leakage current
[The
Initial specified value
The capacitors shall be subjected to 1000 cycle each consisting of charge with the surge voltage specified at 85C for 30 seconds through
a protective resistance (R=33O) and discharge for 5 minutes 30 seconds.
Capacitance
Within
P12%
Psize
change
4 to 6.3V
Within
P12%
A2, A, B3
10 to 16V
Within
P8%
B2, C, D2
20 to 35V
Within
P5%
Dsize
25V 2.2MF (Asize)
Within
P10%
25V 4.7MF (B2size)
Within
P10%
DF (tanE)
[150%
of the Initial specified value
Psize
[The
Initial specified value
A2, A, B3, B2, C, D2, Dsize
(JIS C 5101-1 4.26.)
Leakage current
[The
Initial specified value
Reflow condition : 260C 10 sec.
Capacitance
Within
P20%
4V
Psize
change
Within
P10%
6.3 to 16V
Within
P8%
4 to 10V
A2, A, B3
Within
P5%
16 to 35V
B2, C, D2
Within
P10%
Table1 (without P size)
Dsize
DF (tanE)
[150%
of the Initial specified value
Psize
[The
Initial specified value
A2, A, B3, B2, C, D2, Dsize
Leakage current
[The
Initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 1000 hours at 85C.
Within
P20%
4V
Psize
Capacitance
Within
P12%
6.3 to 16V
change
Within
P12%
4 to 10V
A2, A, B3, B2,
Within
P10%
16 to 35V
C, D2, Dsize
[150%
of the Initial specified value
Psize
DF (tanE)
[The
Initial specified value
A2, A, B3, B2, C, D2, Dsize
[125%
of the Initial specified value
(JIS C 5101-1 4.23.)
Leakage current
See Rated ripple current page, please
1%/1000 hours (85C, Rated voltage, power source impedance : 1O/V)
JIS C 5101-1
-55C
Within
P15%
Within
P10%
[12%
[10%
[8%
[10%
[10%
[13%
[6%
[8%
[10%
[12%
[150%
of the initial limit
(1/3)
CAT. No. E1002G
CHIP TYPE TANTALUM SOLID ELECTROLYTIC CAPACITORS
J case
@Resin
molded chip type
@Case
size : 1.6B0.8B0.8mm
@Pb-free
type
?SPECIFICATIONS
Items
Category
temperature range
Rated Voltage range
Rated Capacitance range
Rated Capacitance tolerance
Leakage current
Dissipation factor
(tane)
Characteristics
at high and
low temperature
-55 to +125C (+85C max. without voltage derating)
2.5 to 16V
dc
(f=120Hz, 20C)(JIS C 5101-1 4.7.)
1.0 to 10MF
P20%
(M)
(After 5 minutes of applying rated voltage at 20C)
I[0.01CV
(JIS C 5101-1 4.9.)
I : Leakage current (MA), C : Rated capacitance (MF), V : Rated voltage (V
dc
)
[20%
2.5V to 10V
[10%
(f=120Hz, 20C)(JIS C 5101-1 4.8.)
16V
-55C
+85C
+125C
Capacitance change
-20 to 0%
0 to +20%
0 to +20%
DF (tanE)
[30%
[The
Initial specified value
[30%
[38%
[The
Initial specified value
[22%
6.3V 10MF
[15%
[The
Initial specified value
[15%
16V 1MF
Leakage current
[0.1CV
or 5MA
[0.125CV
or 6.25MA
-
(JIS C 5101-1 4.24.)
Whichever is greater Whichever is greater
The following specifications shall be satisfied when the capacitors are restored to 20C after subjected them at 40C 90 to 95RH for 500 hours.
Capacitance change Within
P20%
DF (tanE)
[150%
of the Initial specified value
(JIS C 5101-1 4.22.)
Leakage current
[The
Initial specified value
The capacitors shall be subjected to 1000 cycle each consisting of charge with the surge voltage specified at 85C for 30 seconds through
a protective resistance (R=33O) and discharge for 5 minutes 30 seconds.
Capacitance change Within
P20%
DF (tanE)
[The
Initial specified value
(JIS C 5101-1 4.26.)
Leakage current
[The
Initial specified value
Reflow condition : 260C 10 sec.
Capacitance change Within
P20%
DF (tanE)
[The
Initial specified value
Leakage current
[The
Initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 1000 hours at 85C.
Capacitance change Within
P20%
DF (tanE)
[150%
of the Initial specified value
(JIS C 5101-1 4.23.)
Leakage current
[200%
of the Initial specified value
1%/1000 hours (85C, Rated voltage, power source impedance : 1O/V)
JIS C 5101-1
Requirements
Damp heat,
steady state
Surge voltage
Resistance to
soldering heat
Endurance
Failure rate
Standard
(2/3)
CAT. No. E1002G