M9-1273JM2 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> The resistor> M9-1273JM2

M9-1273JM2: DescriptionArray/Network Resistor, Bussed, Metal Glaze/thick Film, 0.125W, 27000ohm, 100V, 5% +/-Tol, -200,200ppm/Cel, 9010,; CategoryPassive components The resistor; File Size53KB，4 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/

Download Datasheet Parametric View All

M9-1273JM2 Overview

Array/Network Resistor, Bussed, Metal Glaze/thick Film, 0.125W, 27000ohm, 100V, 5% +/-Tol, -200,200ppm/Cel, 9010,

M9-1273JM2 Parametric

Parameter Name	Attribute value
Objectid	913411578
Reach Compliance Code	compliant
ECCN code	EAR99
structure	Conformal Coated
Lead length	3.56 mm
lead spacing	2.54 mm
Network Type	Bussed
Number of terminals	9
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package height	4.95 mm
Package length	22.86 mm
Package form	SIP
Package width	2.41 mm
method of packing	Tube
Rated power dissipation(P)	0.125 W
resistance	27000 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	M(BUSSED,5%)
size code	9010
technology	METAL GLAZE/THICK FILM
Temperature Coefficient	200 ppm/°C
Tolerance	5%
Operating Voltage	100 V

Preview

Download Datasheet

View All

MODEL M SERIES

Thick Film

Low Proﬁle SIP

Conformal Coated

Resistor Networks

ELECTRICAL

Standard Resistance Range, Ohms

Standard Resistance Tolerance, at 25°C

Operating Temperature Range

Temperature Coefﬁcient of Resistance

Temperature Coefﬁcient of Resistance Tracking

Maximum Operating Voltage

Insulation Resistance, Minimum

ENVIRONMENTAL

22 to 1Meg

±2% (G Tol.)

Optional: ±1% (F Tol.), ±5% (J Tol.)

-55°C to +125°C

±200ppm/°C

±50ppm/°C

100Vdc or

√PR

10,000 Megohms

Thermal Shock plus Power Conditioning

Short Time Overload

Terminal Strength

Moisture Resistance

Mechanical Shock

Vibration Shock

Low Temperature Storage

High Temperature Exposure

Load Life, 1,000 Hours

Resistance to Solder Heat (Per MIL-STD-202, Method 210, Cond.B)

Dielectric Withstanding Voltage

Marking Permanency

Lead Solderability

Flammability

Storage Temperature Range

Speciﬁcations subject to change without notice.

∆R

0.50%

∆R

0.25%

∆R

0.25%

∆R

0.50%

∆R

0.25%

∆R

0.25%

∆R

0.25%

∆R

0.50%

∆R

1.00%

∆R

0.25%

100V for 1 minute

per MIL-STD-202, Method 215

per MIL-STD-202, Method 208

UL-94V-O Rated

-55°C to +150°C

4-49

Model M Series

Recommended Resources

Traffic traffic light control circuit

Use SH-803R to make high-power holiday lights

High voltage Geiger counter power circuit

Voltage frequency conversion circuit

M51970L steady speed control circuit

Two-phase motor driver circuit

[Telink's new generation of low-power, high-performance, multi-protocol wireless kit B91 review] Zigbee program generation and compilation configuration: [i=s]This post was last edited by damiaa on 2022-10-24 16:41[/i][Telink's new generation of low-power, high-performance, multi-protocol wireless kit B91 review] Zigbee program generation and compilati...; damiaa Domestic Chip Exchange

[STM32F769Discovery development board trial] Build development environment & drive LCD screen to display dot matrix characters & touch screen driver: It has been a while since I received the development board. As I was busy with the NXP project, I have not had time to post. Now I am starting to make up for it.The STM32F769Discovery development boar...; donatello1996 Special Edition for Assessment Centres

For a three-pin package like this, if the components are not removed from the board, will the energy come out to be a diode or a transistor?: Can I use the on-off quantity? Let a big guy explain it in detail...; 小太阳yy Analog electronics

Chuanglong TMS320C6748 development board——UART register introduction and program: 1. UART Registers(1) FIFO Control Register (FCR)RXFIFTL: Receive FIFO interrupt trigger (an interrupt will be generated when the amount of data in the FIFO just reaches the required (trigger level));D...; Aguilera DSP and ARM Processors

What is the use of C language? Is it easy to learn?: I want to learn C language recently. I don’t know whether C language is easy to learn and what I can do after learning it?...; 爱吐泡泡的鱼 Talking

Rebuild Polygons correct usage: Whether the AD/protel software is assembling a board or you accidentally move the copper cladding during the design, how can you return to the PCB board that was not moved before? As shown in the puzz...; szjlcw PCB Design

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components