EEWORLDEEWORLDEEWORLD

Part Number

Search

M55342L10B920ACT0M

Description
Fixed Resistor, Thin Film, 0.5W, 920ohm, 75V, 0.1% +/-Tol, 200ppm/Cel, Surface Mount, 1010, CHIP
CategoryPassive components    The resistor   
File Size96KB,5 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

M55342L10B920ACT0M Overview

Fixed Resistor, Thin Film, 0.5W, 920ohm, 75V, 0.1% +/-Tol, 200ppm/Cel, Surface Mount, 1010, CHIP

M55342L10B920ACT0M Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid296571464
package instructionCHIP
Reach Compliance Codenot_compliant
ECCN codeEAR99
Other featuresNON-INDUCTIIVE, LASER TRIMMABLE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length2.667 mm
Package formSMT
Package width2.54 mm
method of packingTR
Rated power dissipation(P)0.5 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance920 Ω
Resistor typeFIXED RESISTOR
size code1010
surface mountYES
technologyTHIN FILM
Temperature Coefficient200 ppm/°C
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage75 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
Ω
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
D
D
3
3
3D Models
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
Ω
to 6.19 MΩ
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 %, ± 0.25 %, ± 0.5 %, ± 1 %,
± 2 %, 5 %, ± 10 %
ΔR
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-65 °C to +150 °C
-65 °C to +150 °C
< - 25 dB
ΔR
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 15-Nov-2021
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
How to design a triode amplifier circuit
Design Steps 1) Analyze and design requirementsThe voltage gain can be used to calculate the voltage amplification factor; the maximum output voltage can be used to set the power supply voltageThe out...
fish001 Analogue and Mixed Signal
[RISC-V MCU CH32V103 Evaluation] IIC Hardware Test (Part 2)
After the guidance of WCH technicians, I found the problem in my program. The I2C devices used in my program were inconsistent. I uploaded the correct file at the end of the article for your reference...
bigbat Domestic Chip Exchange
I work in the field of industrial control, electronics and hardware are both possible
Are there many people in the industrial control field on this site?...
chuxiang Industrial Control Electronics
Requesting Jlink script for ARM-A9
I recently wanted to use Jlink to connect to S5P4418 and play bare metal programming, but I found that Jlink could not connect to the CPU, as shown in the figure. I asked netizens to help me write a J...
瓜弟 ARM Technology
C5517 FFT hardware accelerator performs calculations sometimes well and sometimes poorly
[align=left][color=rgb(85, 85, 85)][font="][size=4]Using the hardware accelerator to calculate 128-point fft, the data was wrong at the beginning. After many attempts, it was finally successful under ...
灞波儿奔 DSP and ARM Processors
Talk about the future applications of drones and get points for speaking up
[align=center][media=x,500,375]https://v.youku.com/v_show/id_XMzE2NDE1MjE2.html?spm=a2h0k.11417342.soresults.dtitle&s=56a3eba4e5a311e0a046[/media][/align] [size=4]First, let me show you a drone that I...
高进 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号