EEWORLDEEWORLDEEWORLD

Part Number

Search

WBC-T0303AG-03-7962-CB

Description
Array/Network Resistor, Center Tap, Thin Film, 0.25W, 79600ohm, 100V, 0.25% +/-Tol, -25,25ppm/Cel, 0303,
CategoryPassive components    The resistor   
File Size376KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

WBC-T0303AG-03-7962-CB Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 79600ohm, 100V, 0.25% +/-Tol, -25,25ppm/Cel, 0303,

WBC-T0303AG-03-7962-CB Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid802620779
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
resistance79600 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBC(TAPPED)
size code0303
technologyTHIN FILM
Temperature Coefficient-25,25 ppm/°C
Tolerance0.25%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC Advanced Film Division
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
R
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Back contact
Noise
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
Passivation
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Gold available)
Gold
3KÅ minimum
Silicon Dioxide or
Silicon Nitride
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
R
Top contact
pad chamfered
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
Backside
½R
½R
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue April 2006
Share the troubleshooting of using bq34z100 chip
1. bq34z100 current calibration problem: 1. In the current calibration section of the bq34z100EVM Wide Range Impedance Track Enabled Battery Fuel Gauge Solution manual, sentence 4: Connect and measure...
qwqwqw2088 Analogue and Mixed Signal
The salary and development path of hardware engineers
LZ is in the second year of graduate school. Although his major is electronics, the application is awkward. It is in the direction of electronic readout for large-scale particle detection. With the ec...
Lightfly201 Talking about work
Silicon technology leads the era of automotive design
Abstract: With the continuous development of science and technology, the degree of automobile electronics is getting higher and higher, and semiconductor technology is also rising. This article descri...
frozenviolet Automotive Electronics
Here are some questions about the differential signal amplifier circuit
Because the op amp is powered by a single power supply, a bias voltage VCM1 of tens of mV must be added (why?). I see that the classic differential amplifier circuits are all grounded? Also, I used a ...
西里古1992 Analog electronics
How to Meet the Testing Challenges of Multi-Antenna Systems
With the rapid growth of applications with higher data rates such as 5G, wireless systems are faced with the requirements of wider bandwidth and wider network coverage. Multi-antenna technologies, suc...
btty038 RF/Wirelessly
A beginner was trapped by the garbage code of the development board for a whole night
I am using the AX309 development board from Heijin and I am a beginner in FPGA. Today I simulated the serial port routine in their tutorial. First, I had a problem simulating a simple clock divider mo...
lingking FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号