Exceeding any one or a combination of these limits may cause permanent damage
.
Exceeding any one or a combination of the Absolute
Maximum Rating conditions may cause permanent
damage to the device. Extended application of Absolute
Maximum Rating conditions to the device may reduce
device reliability. Specified typical performance or
functional operation of the device under Absolute
Maximum Rating conditions is not implied.
Nominal Operating Parameters
Specification
Parameter
Min
General Performance
Small Signal Power Gain, S21
16.0
17.0
13.0
10.8
Gain Flatness, GF
Input VSWR
11.5
±0.65
1.65:1
1.65:1
1.75:1
Output VSWR
1.5:1
1.9:1
2.2:1
Bandwidth, BW
Output Power at -1dB
Compression, P1dB
4.7
12.0
14.6
Noise Figure, NF
Third Order Intercept, IP3
4.1
+29.6
+27.3
Reverse Isolation, S12
Device Voltage, V
D
Gain Temperature Coefficient,
/
3.6
-18
3.9
-0.0015
Unit
Typ
Max
Condition
V
D
= +3.9V, I
CC
= 47mA, Z
0
= 50Ω, T
A
= +25°C
dB
dB
dB
dB
f = 0.1GHz to 1.0GHz
f = 1.0GHz to 4.0GHz
f = 4.0GHz to 6.0GHz
f = 0.1GHz to 2.0GHz
f = 0.1GHz to 4.0GHz
f = 4.0GHz to 6.0GHz
f = 6.0GHz to 10.0GHz
f = 0.1GHz to 4.0GHz
f = 4.0GHz to 6.0GHz
f = 6.0GHz to 10.0GHz
GHz
dBm
dBm
dB
dBm
BW3 (3dB)
f = 2.0GHz
f = 6.0GHz
f = 3.0GHz
f = 2.0GHz
f = 6.0GHz
dB
4.2
V
dB/°C
f = 0.1GHz to 12.0GHz
RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421
For sales or technical support, contact RFMD at +1.336.678.5570 or
customerservice@rfmd.com.
DS131016
The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of
third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended
application circuitry and specifications at any time without prior notice.
2 of 9
NLB-400
Specification
Parameter
Min
MTTF versus Temperature
at I
CC
= 50mA
Case Temperature
Junction Temperature
MTTF
85
119
>1,000,000
°C
°C
hours
Unit
Typ
Max
Condition
Thermal Resistance
θ
JC
185
°C/W
RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421
For sales or technical support, contact RFMD at +1.336.678.5570 or
customerservice@rfmd.com.
DS131016
The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of
third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended
application circuitry and specifications at any time without prior notice.
3 of 9
NLB-400
Pin Names and Descriptions
Pin
1
Name
RFIN
Description
RF input pin. This pin is NOT internally DC blocked. A DC blocking
capacitor, suitable for the frequency of operation, should be used
in most applications. DC coupling of the input is not allowed,
because this will override the internal feedback loop and cause
temperature instability.
Ground connection. For best performance, keep traces physically
short and connect immediately to ground plane.
RF output and bias pin. Biasing is accomplished with an external
series resistor and choke inductor to V
CC
. The resistor is selected
to set the DC current into this pin to a desired level. The resistor
value is determined by the following equation:
Interface Schematic
2
3
GND
RFOUT
Care should also be taken in the resistor selection to ensure that
the current into the part never exceeds maximum datasheet
operating current over the planned operating temperature. This
means that a resistor between the supply and this pin is always
required, even if a supply near 5.0V is available, to provide DC
feedback to prevent thermal runaway. Because DC is present on
this pin, a DC blocking capacitor, suitable for the frequency of
operation, should be used in most applications. The supply side of
the bias network should also be well bypassed.
4
GND
Same as pin 2.
Package Drawing
RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421
For sales or technical support, contact RFMD at +1.336.678.5570 or
customerservice@rfmd.com.
DS131016
The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of
third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended
application circuitry and specifications at any time without prior notice.
4 of 9
NLB-400
Typical Bias Configuration
NOTE: Application notes related to biasing circuit, device footprint, and thermal considerations are available on request.
Recommended Bias Resistor Values
Supply Voltage, V
CC
(V)
Bias Resistor, R
CC
(Ω)
5
23
8
87
10
129
12
172
15
236
20
343
RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421
For sales or technical support, contact RFMD at +1.336.678.5570 or
customerservice@rfmd.com.
DS131016
The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of
third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended
application circuitry and specifications at any time without prior notice.
Wind Turbine Tower Disaster Early Warning SystemAuthor: wushuisheng1. Project Background
As an important field of new energy development, wind power generation has received more and more attention. Th...
[i=s]This post was last edited by dcexpert on 2021-9-1 11:18[/i]Add USB/JTAG support for ESP32-C3. Use USB as programming and terminal interface, not UART.Add a new board type for ESP32-C3 revision 3 ...
When it comes to base stations, the first thing that comes to mind is a huge, straight-man steel tower.
Not to mention other things, the land occupation and material cost of the steel frame structure ...
We use radio frequency (RF) communications in our daily activities, whether calling a relative, texting a friend, or even reading this blog post on a mobile device. There are many signals traveling qu...
[align=left] [/align][align=left]Please note that before outputting GERBER, you must first consider whether the via (VIA) is open or covered with oil. The following introduces how each software handle...
The purpose is to briefly introduce the company's current design process. If there is anything wrong with the introduction, please feel free to point it out.
2 Design steps:
2.1 Draw circ...[Details]
With the continuous development of network technology and communication technology and the continuous improvement of people's living requirements, the realization of home intelligent control has be...[Details]
With the widespread application of semiconductor materials such as silicon, people have begun to pay attention to more materials in order to make electronic products with higher cost performance and ...[Details]
After the Spring Festival, many companies are facing the problem of difficulty in recruiting workers, which has lasted for many years. As labor costs rise, more and more small and medium-sized manufa...[Details]
1 Introduction
Due to the renewable and clean nature of fuel, electric vehicles have gradually become the object of the country's vigorous development in the
new energy vehicle
...[Details]
Abstract: DC-DC power system efficiency is a very critical issue in compact electronic equipment. The interaction between various parts of the DC-DC power supply system and the main factors affe...[Details]
principle: Because there are 8 digital tubes, we must use a 38-bit decoder to save the resources of the microcontroller. Here we will briefly introduce the principle of the 38-bit decoder, and then...[Details]
Shimadzu, Agilent and Waters. I personally think the first two are more common. Shimadzu is relatively cheap and very durable. Generally, it is well maintained. Except for the replacement of consumab...[Details]
This display device circuit uses a single-line oscilloscope to display 4 continuous signals at the same time, so as to compare the time relationship of different signals. CC4017 is an oscillator and...[Details]
In fact, the IROM code of Exynos 4412 has already set the PLL. We can print out the PLL register values set by IROM through the serial port. These values are printed out like this (excerpted from...[Details]
The financial report released today (28) by Taiwan-based packaging and testing company ASE Technology Holding Co., Ltd. shows that the company's consolidated revenue in the third quarter was NT$150.6...[Details]
1 Introduction With the rapid development of science and technology and economy, people's concept of home has changed from simple living to focusing on humanized housing needs, such as safe, comforta...[Details]
V-cone flowmeter (throttling differential pressure flowmeter) and vortex flowmeter are the core flowmeters and the main measuring flowmeters. The throttling differential pressure flowmeter is mainly a...[Details]
As electrical demands grow, automobiles require regional modules to meet a wide range of power needs. High-side switches enable design flexibility and enable space- and weight-saving solutions by r...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
