EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

HPH1A21SGA

Description
Board Connector, 21 Contact(s), 1 Row(s), Male, Straight, 0.05 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size83KB,1 Pages
ManufacturerAdam Tech
Download Datasheet Parametric View All

HPH1A21SGA Overview

Board Connector, 21 Contact(s), 1 Row(s), Male, Straight, 0.05 inch Pitch, Solder Terminal, Black Insulator, Receptacle

HPH1A21SGA Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresROHS COMPLIANT
body width0.071 inch
subject depth0.039 inch
body length1.05 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedTIN OVER COPPER
Contact point genderMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact resistance20 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage1000VAC V
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialNYLON
Manufacturer's serial numberHPH1
Plug contact pitch0.05 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
PCB contact patternRECTANGULAR
Plating thicknessFLASH inch
Rated current (signal)1 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.091 inch
Terminal pitch1.27 mm
Termination typeSOLDER
Total number of contacts21
About the compilation speed when compiling STM32 with MDK
The most commonly used compilers for developing STM32F are generally MDK and IAR. IAR is relatively simple and has slightly better compilation efficiency. MDK simulation effect is better, and most peo...
懒猫爱飞 stm32/stm8
Can the same-phase AC amplifier circuit be used for low frequencies?
[align=left][font=微软雅黑][size=12.0pt]The capacitor Ci next to R4 is equivalent to an open circuit for DC, so the DC component is not amplified; it is equivalent to a short circuit for AC, so the AC amp...
sfcsdc Analog electronics
TLP3547 Evaluation Board Preliminary Evaluation Report
[align=center][color=#000000]Preliminary Evaluation Report on TLP3547 Evaluation Board[/color][/align][align=center][color=#000000] [/color][/align][align=center][color=#000000] Sichuan Institute of A...
wangdh45 Toshiba Photorelays TLP3547 Review
Share: Where should the inductor be placed on the power supply PCB?
[size=4]First, let’s ask the question: where should the coil be placed? [/size] [size=4] [/size] [size=4] Switching regulators for voltage conversion use inductors to temporarily store energy. These i...
qwqwqw2088 Analogue and Mixed Signal
How to choose the right AFE for BMS
AFE (analog front end) is analog front end in Chinese. It refers to the battery sampling chip in BMS, which is used to collect battery cell voltage and temperature, etc.Before writing this, I thought ...
qwqwqw2088 Analogue and Mixed Signal
EEWORLD University Hall----Motor and Drag (Motor Part) Harbin Institute of Technology
Motor and Drag (Motor Part) Harbin Institute of Technology : https://training.eeworld.com.cn/course/5318Mr. Li Yong from Harbin Institute of Technology teaches motors and traction motors...
木犯001号 Industrial Control Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号