IP Rating ............................................................ IP 40 .....................................................................IP 40
*RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Model 91, 92, 93, 94 & 95 - 5/8 ” Square Single-Turn Panel Control
Mechanical Characteristics
1
Stop Strength (1/4 ” D shaft) .............................................................................................................................................45.19 N-cm (4 lb.-in.)
(1/8 ” D shaft) .............................................................................................................................................33.89 N-cm (3 lb.-in.)
Starting ........................................................................................................................................... 0.3 max. above average running torque
Running Torque
Single or Dual Section (A & R Bushings) .................................................................................................. 0.21 to 1.06 N-cm (0.3 to 1.5 oz.-in.)
Single or Dual Section (C & U Bushings) .................................................................................................. 0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Mounting .............................................................................................................................................1.7-2.0 N-m (15-18 lb.-in.) maximum
Variation ...................................................................................................................... 0.35 N-cm (0.5 oz.-in.) maximum in 45 ° shaft travel
Weight (Single Section, Metal Bushing)...............................................................................................................................12.7 grams nominal
Terminals .................................................................................................................................Printed circuit terminals, J-Hooks or solder lugs
Soldering Condition ...........................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ” wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.
Marking ..................................................................................Manufacturer’s trademark, date code, resistance, manufacturer’s part number
Ganging (Multiple Section Potentiometers).............................................................................................................................2 cups maximum
Hardware ...................One lockwasher and one mounting nut is shipped with each potentiometer, except where noted in the part number.
NOTE:
1
At
Performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Model 91, 92, 93, 94 & 95 - 5/8 ” Square Single-Turn Panel Control
Product Dimensions
Model 91 PC Pin Terminals, In-Line
22.86 ± 0.43
(.900 ± .017)
MOUNTING
SURFACE
L
12.70 ± .229
(.500 ± .009)
0.79 ± .025
(.031 ± .010)
DIA.
13.72 ± 0.38
(.540 ± .015)
1.37 ± 0.08
(.054 ± .003)
2.36 ± 0.08
(.093 ± .003)
15.88
(.625)
7.92
(.312)
Model 92 J-Hooked
Terminals, In-Line
.79
(.031) 2 PLCS.
3 2 1
.254
(.010)
GAP
SEE
HOW TO ORDER
CHART FOR
BUSHING OPTIONS.
10.16 ± 0.30
(.400 ± .012)
11.05 ± 0.20
(.435 ± .008)
SEE
NEXT PAGE
FOR SHAFT
OPTIONS.
1.19
(.047)
“A” STYLE
A.R. LUG
R
9.53
(.375)
15.29 ± 0.56
(.602 ± .022)
5.08
(.20)
1.52
(.06)
R2
R1
1
2
3
1
2
3
2.54
(.100)
2.54
(.100)
Model 94 J-Hooked
Terminals, "L" Pattern
0.76 ± 0.05
(.030 ± .002)
TYP.
Model 93 PC Pin Terminals, "L" Pattern
22.86 ± 0.43
(.900 ± .017)
MOUNTING
SURFACE
L
12.70 ± .229
(.500 ± .009)
0.79 ± .025
(.031 ± .010)
DIA.
13.72 ± 0.38
(.540 ± .015)
1.37 ± 0.08
(.054 ± .003)
2.36 ± 0.08
(.093 ± .003)
15.88
(.625)
7.92
(.312)
3 2 1
1.52
(.06)
GAP
.81
(.032)
R. MAX.
5.33 ± .76
(.21 ± .03)
3.81
(.150)
MAX. TYP.
SEE
HOW TO ORDER
CHART FOR
BUSHING OPTIONS.
DIA.
0.81
TYP.
(.032)
10.16 ± 0.30
(.400 ± .012)
R2
R1
5.08 ± 0.38
(.200 ± .015)
11.05 ± 0.20
(.435 ± .008)
SEE
NEXT PAGE
FOR SHAFT
OPTIONS.
1.19
(.047)
“A” STYLE
A.R. LUG
R
9.53
(.375)
12.7 ± 1.02
(.500 ± .040)
Shaft Flat Orientation
2.54
(.100)
2.54
(.100)
120 ° ± 5 ° STD.
FLAT ORIENTATION
(SHAFT AT CCW END)
1
3
2
1
3
2
0.76 ± 0.05
(.030 ± .002)
TYP.
1
CCW
2
POTENTIOMETER
3
Model 95 Solder Lug Terminals, "Triangular" Pattern
A: The kernel driver does not support higher versions of eMMC.
Is there a modified Android 4.4.2 kernel image that can be sent to me for testing?
B:
We have not updated 4.4.2, you can compile and modi...
As the signal rise time decreases and the signal frequency increases, the EMI problem of electronic products has also been paid more and more attention by electronic engineers. The success of high-spe...
[size=4] Integrated operational amplifiers are highly versatile active devices. They can be used not only for signal calculation, processing, transformation and measurement, but also for generating si...
Most of the input and output lines of the MSP430 microcontroller are used. Except for some individual ports, they are basically 8-bit in a group. The ports of different models of MSP430 are different....
I am a newbie in microcontrollers, please give me some advice!!!
Design a battery voltage detection device
Voltage displayed on LCD1602
When the voltage is lower than 2.6V, the indicator light flashes...
[i=s]This post was last edited by dql2016 on 2021-1-16 16:59[/i]The MCU used in the NUCLEO-L552ZE board is STM32L552ZET6. The STM32L552xx is based on the Cortex-M33 core , the Armv8-M with Mainline ex...
Who is better at performing surgery: an experienced surgeon or a robot?
Typically, surgeons must make relatively large incisions during surgery, while the robot's small instruments can fit int...[Details]
int main( void )
{
Bsp_Init();
os_sys_init_user( Task_SysInit,
50,
gTaskStack_SysInit,
DEF_StakSize_SysInit ); //System initializes and runs the first task with 4 param...[Details]
The issuance of 4G licenses was finally settled in the last month of 2013.
The Ministry of Industry and Information Technology's Electricity Administration announced yesterday that it had issued ...[Details]
The basic structure of GPIO First: Open-drain output mode (N-MOS is turned on, when the level is high, the IO port level depends on the external pull-up resistor; when the level is low...[Details]
I compared the cost-effective iQOO 3 and the offline-focused X30 Pro_Sina Public Test As usual, I still got the latest iQOO 3 released by iQOO as soon as possible. I compared the cost-effecti...[Details]
Abstract: Professional large-scale disk storage systems have developed into large array systems containing multiple disks. As the number of disks in the system continues to increase, the possibilit...[Details]
Target This event is a continuation of the November Student Zone; this time we will introduce current mirrors, whose output is not affected by changes in input current. Therefore, it will be helpf...[Details]
At present, ECG monitoring systems that mainly collect, analyze and diagnose ECG signals have been widely used, and have played a great role in the prevention and diagnosis of heart diseases. Howev...[Details]
The "Golden Nine and Silver Ten" peak season of the automobile industry is approaching. Tesla, Volkswagen and other manufacturers have launched a wave of price cuts in August, trying to occupy a favo...[Details]
O Introduction
Power management system has become a hot spot in the current development of the integrated circuit industry and is also an indispensable technology. Without power management...[Details]
In the power supply and distribution system, the distribution transformer generally supplies power to the load, and the current flows from the grid side to the load, which is called forward current...[Details]
Target The goal of this lab activity is to study a circuit that connects an analog signal to the digital external trigger signal input of the ADALM2000 module. background knowledge The more co...[Details]
In the actual project development process, hardware circuits often need to be modified, and the modified parts need to modify the driver. Thinking about the coming and going of such requirements is t...[Details]
introduction
Since the 1990s, with the continuous reduction of the feature line width of integrated circuits and the corresponding increase in chip density and operating frequency, reducing pow...[Details]
In some single-chip microcomputer systems, it is sometimes necessary to use some one-key multi-function technologies. Let me introduce them to you here. Switch SP1 is connected to the P3.7/RD pin. ...[Details]
Industrial Control Electronics
京公网安备 11010802033920号
EEWORLD
