FFW-FC11B2508 datasheet, PDF - EEWORLD Datasheet

FFW-FC11B2508: DescriptionWavelength Division Mux/Demux, 955nm Min, 970nm Max, 1X2 Port, ST Connector,; CategoryWireless rf/communication Optical fiber; File Size136KB，5 Pages; ManufacturerLumex; Websitehttps://www.lumex.com; Environmental Compliance

Download Datasheet Parametric View All

FFW-FC11B2508 Overview

Wavelength Division Mux/Demux, 955nm Min, 970nm Max, 1X2 Port, ST Connector,

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Reach Compliance Code	compliant
Other features	IT OPERATES AT SIGNAL WAVELENGTH OF 1528 TO 1563 NM
Communication standards	TELCORDIA-GR-1221
Connection Type	ST CONNECTOR
Fiber optic equipment types	WAVELENGTH DIVISION MUX/DEMUX
Maximum insertion loss	0.2 dB
Minimum isolation	18 dB
Maximum operating temperature	75 °C
Minimum operating temperature	-40 °C
Maximum operating wavelength	970 nm
Minimum operating wavelength	955 nm
Nominal operating wavelength	960 nm
Port configuration	1X2
minimum return loss	55 dB

bq76930 error in reading temperature value: bq76930 error in reading temperature value Most of the time, the current, voltage and temperature are normal, but from time to time the temperature will be read as very high, higher than 100 degrees, ...; lin196@21cn.com Analogue and Mixed Signal

EEWORLD University Hall----Live Replay: Detailed Explanation of Ultra-Low Power RSL10 Bluetooth SoC Development Board: Live replay: Detailed explanation of ultra-low power RSL10 Bluetooth SoC development board : https://training.eeworld.com.cn/course/6056...; hi5 Integrated technical exchanges

Share the problem and solution of using TB to capture pulse width of MSP430: Hardware: MCU: MSP430F149Crystal: 32K, 8MInput signal: 10ms low level, 7.5ms high level received via wireless,Input port: P4.0 (TB0)Requirement: Capture the pulse width of the low level Software:1. In...; 火辣西米秀 Microcontroller MCU

When using CPLD to decode AES/EBU audio, the decoded data has spike pulses. What is the reason?: I used CPLD to make an AES/EBU audio decoder. I used a 50MHZ crystal oscillator as a counter to count. I decoded the data stream based on the counter size. I used a sine wave as the source. The peak-t...; XCXBD EE_FPGA Learning Park

Position2Go Review 4. Structure: This section attempts to describe the structure of P2G hardware and software at a certain level. Regarding the hardware composition and a rough introduction of Position2Go, the official provides two A...; freebsder Special Edition for Assessment Centres

51 single chip digital tube display: Why does the tens digit flash after this program is written into the microcontroller, but yours does not? Please give me some advice, thank you #include #define uchar unsigned char #define uint unsign...; 123哈哈哈 51mcu

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components