EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

HPD041SMWKO020

Description
Board Connector, 41 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Receptacle,
CategoryThe connector    The connector   
File Size485KB,30 Pages
ManufacturerHypertac Ltd
Download Datasheet Parametric View All

HPD041SMWKO020 Overview

Board Connector, 41 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Receptacle,

HPD041SMWKO020 Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
ECCN codeEAR99
body width0.252 inch
subject depth0.315 inch
body length2.717 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU
Contact point genderMALE
Contact materialCOPPER ALLOY
contact modeSTAGGERED
Contact resistance7 mΩ
Contact styleRND PIN-SKT
Dielectric withstand voltage1400VAC V
Durability2000 Cycles
Insulation resistance5000000000 Ω
Manufacturer's serial numberHPD
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
PCB contact patternSTAGGERED
PCB contact row spacing2.54 mm
Plating thickness50u inch
Rated current (signal)4 A
reliabilityCOMMERCIAL
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts41
[AB32VG1 development board review] Light up RGB_LED
There is an RGB_LED on the AB32VG1 development board. The schematic diagram of the RGB_LED is shown in Figure 1, through which you can learn how to use GPIO.Figure 1 RGB_LED circuit The pin connection...
jinglixixi Domestic Chip Exchange
【ST NUCLEO-H743ZI Review】(4) First experience with MQTT in IoT
[i=s]This post was last edited by bigbat on 2019-2-25 19:39[/i] I was very frustrated because of the failure of lwIP of stm32cubeMX. I saw the TCP/IP post by [url=home.php?mod=space&uid=374032]@54chen...
bigbat stm32/stm8
TM4C serial port transmission failed
The code written according to the official routine uses serial port 2. If you don’t want to use interrupts to send and receive, use the sending function void UART2_init(void) { SysCtlPeripheralEnable(...
627933142 Microcontroller MCU
TI buck-boost supercapacitor charging solution
[i=s]This post was last edited by qwqwqw2088 on 2020-11-1 09:20[/i]Supercapacitors are becoming more and more popular in many applications due to their charging times, better transient performance, si...
qwqwqw2088 Analogue and Mixed Signal
EMCV transplantation problem, first time using DSP, don't quite understand
This is my first time using DSP, and I don't know much about it. I found a few tutorials on porting the EMCV library, and followed them. But when I tested it, the program got stuck when it reached cvC...
xiaoxx DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号