The failure rate (λ) and mean time between failures
(MTBF= 1/ λ) is calculated at max output power and
an operating ambient temperature (T
A
) of +40°C. CUI
Power Modules uses Telcordia SR-332 Issue 2 Method 1 to
calculate the mean steady-state failure rate and standard
deviation (σ).
Telcordia SR-332 Issue 2 also provides techniques to
estimate the upper confidence levels of failure rates based
on the mean and standard deviation.
Mean steady-state failure rate, λ Std. deviation, σ
421 n F ailures/h
60.9 nF ailures/h
the responsibility of the installer to ensure that the
final product housing these components complies with
the requirements of all applicable safety standards and
regulations for the final product.
Component power supplies for general use should comply
with the requirements in IEC/EN/UL 60950 1 Safety
of Information Technology Equipment. Product related
standards, e.g. IEEE 802.3af Power over Ethernet, and
ETS 300132 2 Power interface at the input to telecom
equipment, operated by direct current (dc) are based on
IEC/EN/UL 60950 1 with regards to safety.
CUI Power Modules DC/DC converters and DC/DC
regulators are UL 60950-1 recognized and certified in
accordance with EN 60950-1. The flammability rating for
all construction parts of the products meet requirements
for V-0 class material according to IEC 60695-11-10, Fire
hazard testing, test flames – 50 W horizontal and vertical
flame test methods.
Isolated DC/DC converters
Galvanic isolation between input and output is verified
in an electric strength test and the isolation voltage
(V
iso
) meets the voltage strength requirement for basic
insulation according to IEC/EN/UL 60950-1.
It is recommended to use a slow blow fuse at the input
of each DC/DC converter. If an input filter is used in the
circuit the fuse should be placed in front of the input filter.
In the rare event of a component problem that imposes a
short circuit on the input source, this fuse will provide the
following functions:
• Isolate the fault from the input power source so as not to
affect the operation of other parts of the system
• Protect the distribution wiring from excessive current and
power loss thus preventing hazardous overheating
The DC/DC converter output is considered as safety extra
low voltage (SELV) if one of the following conditions is
met:
•The input source has double or reinforced insulation from
the AC mains according to IEC/EN/UL 60950-1
•The input source has basic or supplementary insulation
from the AC mains and the input of the DC/DC converter
is maximum 60 Vdc and connected to protective earth
according to IEC/EN/UL 60950-1
•The input source has basic or supplementary insulation
from the AC mains and the DC/DC converter output is
connected to protective earth according to IEC/EN/UL
60950-1
Non - isolated DC/DC regulators
The DC/DC regulator output is SELV if the input source
meets the requirements for SELV circuits according to IEC/
EN/UL 60950-1.
MTBF (mean value) for the NEB series = 2.91 Mh.
MTBF at 90% confidence level = 2.37 Mh
Compatability with RoHS requirements
The products are compatible with the relevant clauses
and requirements of the RoHS directive 2011/65/EU and
have a maximum concentration value of 0.1% by weight
in homogeneous materials for lead, mercury, hexavalent
chromium, PBB and PBDE and of 0.01% by weight in
homogeneous materials for cadmium.
Exemptions in the RoHS directive utilized in CUI
Power Modules products are found in the Statement of
Compliance document.
Safety Specification
General Information
CUI Power Modules DC/DC converters and DC/DC
regulators are designed in accordance with the safety
standards IEC60950-1, EN60950-1 and UL60950-1 Safety
of Information Technology Equipment
IEC/EN/UL60950-1 contains requirements to prevent
injury or damage due to the following hazards:
•
•
•
•
•
•
Electrical Shock
Energy hazards
Fire
Mechanical and heat hazards
Radiation hazards
Chemical hazards
On-board DC/DC converters and DC/DC regulators are
defined as component power supplies. As components
they cannot fully comply with the provisions of any
safety requirements without “conditions of acceptability”.
Clearance between conductors and between conductive
parts of the component power supply and conductors on
the board in the final product must meet the applicable
safety requirements. Certain conditions of acceptability
apply for component power supplies with limited stand-off
(see Mechanical Information for further information). It is
cui.com
For more information, please visit the
product page.
CUI Inc
│
SERIES:
NEB-D
│
DESCRIPTION:
FULLY REGULATED ADVANCED BUS CONVERTERS
date
06/10/2016
│
page
4 of 36
Absolute Maximum Ratings
parameter
operating temperature (T
P1
)
storage temperature (T
S
)
input voltage (V
I
)
isolation voltage (V
iso
)
input voltage transient (V
tr
)
remote control pin voltage (V
RC
)
SALERT, CTRL, SCL, SDA, SA0,
SA1 (V Logic I/O)
input to output test voltage, see note 1
according to ETSI EN 300 132-2 and Telcordia GR-
1089-CORE
see operating information section
-0.3
-0.3
conditions/description
see thermal consideration section
min
-40
-55
-0.5
typ
max
+125
+125
+80
+65*
2250
+100
+80*
18
3.6
units
°C
°C
V
Vdc
V
V
V
Stress in excess of Absolute Maximum Ratings may cause permanent damage. Absolute Maximum Ratings, sometimes referred to as no destruction limits, are normally tested with one
parameter at a time exceeding the limits in the Electrical Specification. If exposed to stress above these limits, function and performance may degrade in an unspecified manner.
Note 1: Isolation voltage (input/output to base-plate) max 750 Vdc.
* Applies for the narrow input version V
I
= 40-60 V
Fundamental Circuit Diagram
+IN
Driver
+OUT
-OUT
-IN
Auxillary
Supply
Driver
Control
RC
RC isolation
cui.com
For more information, please visit the
product page.
CUI Inc
│
SERIES:
NEB-D
│
DESCRIPTION:
FULLY REGULATED ADVANCED BUS CONVERTERS
date
06/10/2016
│
page
5 of 36
Functional Description
T
P1
, T
P3
= -40 to +90ºC, V
I
= 36 to 75 V, sense pins connected to output pins unless otherwise specified under Conditions.
Typical values given at: T
P1
, T
P3
= +25°C, V
I
= 53 V, max I
O
, unless otherwise specified under Conditions
Configuration File: 190 10-CDA 102 0315/001
parameter
PMBus monitoring accuracy
input voltage (VIN_READ)
output voltage (VOUT_READ)
output current (IOUT_READ)
temperature (TEMP_READ)
fault protection
characteristics
factory default
setpoint accuracy
hysteresis: factory default
hysteresis: configurable via PMBus of threshold
range, note 1
delay
factory default
configurable via PMBus, note 1
fault response time
factory default
configurable via PMBus, note 1
fault response time
setpoint accuracy (I
O
)
IOUT_OC_FAULT_LIMIT: factory default
IOUT_OC_FAULT_LIMIT: configurable via PMBus,
note 1
fault response time
OTP_FAULT_LIMIT: factory default
OTP_FAULT_LIMIT: configurable via PMBus, note 1
hysteresis: factory default
hysteresis: configurable via PMBus, note 1
fault response time
0
0
32
0.5
2
300
0
0
200
15.6
200
25
200
-50
0
125
10
300
125
125
16
1
V
V
V
V
μs
V
V
μs
V
V
μs
%
A
A
μs
C
C
º
C
º
C
μs
º
º
conditions/description
min
-2
typ
±0.5
±0.1
±0.15
5
max
2
1.0
6
0.6
10
units
%
%
%
A
º
V
I
= 53V
V
I
= 53V, 50-100% of max I
O
V
I
= 53V, 10% of max I
O
controller IC internal sensor
-1.0
-6
-0.6
0
C
input under voltage lockout
(UVLO)
output voltage - under voltage
protection (VOUT_UV_FAULT_
LIMIT)
output voltage - over voltage
protection (VOUT_OV_FAULT_
LIMIT)
V
OUT
-6
0
16
6
100
over current protection (OCP)
over temperature protection
(OTP)
logic input/output
characteristics
logic input low (V
IL
)
logic input high (V
IH
)
logic output low (V
OL
)
logic output high (V
OH
)
bus free time T(BUF)
Note
CTRL, SA0, SA1, PG, SCL, SDA
CTRL, SA0, SA1, PG, SCL, SDA
CTRL, PG, SALERT, SCL, SDA
I
OL
= 6 mA
CTRL, PG, SALERT, SCL, SDA
I
OH
= -6 mA
note 2
2.7
1.3
2.1
1.1
V
V
0.25
V
V
μs
1: See Operating Information section.
2: PMBus timing parameters according to PMBus spec.
Where do you usually go to purchase components? Today I recommend element160:Global electronic components distributor, providing you with local support
A reliable partner to meet all your product need...
Smart cards can be divided into three categories according to their security level: memory cards, logic encryption cards and CPU cards, among which CPU cards have the highest security level. As can be...
TI Cup 2019 National Undergraduate Electronic Design Competition Question Analysis and Technical Exchange Seminar : https://training.eeworld.com.cn/course/5726TI Cup 2019 National Undergraduate Electr...
I saw the information about Raspberry Pi Pico on the EEWORLD official account, so I immediately went to the official website to learn more.
I saw the purchase information at the bottom, and then I imm...
One of the more troublesome problems of hydrogen energy batteries is the escape of hydrogen. Hydrogen is easy to escape when the pressure is high because of its small molecules. The capacity of the cy...
On March 30, Qianfang Technology released its 2021 annual report, stating that the company's annual revenue reached 10.281 billion yuan, a year-on-year increase of 9.15%; the full-year net profit att...[Details]
For the second-tier new forces, they know that listing in Hong Kong may be a quagmire and they need to struggle hard to break through, but the time has come when they have to do it. “When it comes...[Details]
1 Introduction
This article introduces a single-chip multi-machine
parallel communication system, using 89C51 as the host and multiple 89C2051 as slaves. (89C2051 is a 20-pin 300MIL p...[Details]
Labview programs are also called virtual instruments , or NI, and their appearance and operation are similar to real physical instruments (such as oscilloscopes and multimeters ).
Labview cons...[Details]
Today, vivo released the S5 in Hangzhou, which has a stylish appearance and 5-layer ultra-textured beauty. The 8GB+128GB version is priced at 2,698 yuan, and the 8GB+256GB version is priced at 2,998 ...[Details]
Introduction I recently took on a tachometer project, the principle is to measure frequency. At first, I used an external interrupt, and then took the value according to the timer timing of one secon...[Details]
Recently, Fenghua High-Tech stated in an institutional survey that the first phase of the company's Xianghe Industrial Park high-end capacitor base project has a designed production capacity of 5 bil...[Details]
In the ARM processor, the execution of the program is mainly controlled by 3 situations: 1. The program is executed in a pipeline manner. The value of PC is the address of the next instruction, that ...[Details]
With the advancement of the 30·60 dual carbon goals, building an energy supply system dominated by clean and low-carbon energy such as wind power and photovoltaic power has become an important goal...[Details]
Due to the continuous advancement of technology and the introduction of recommended and mandatory standards, the energy efficiency of power supplies is constantly improving. It is estimated that in...[Details]
IDC predicts that global semiconductor revenue will reach US$661 billion in 2022, a year-on-year increase of 13.7%, setting a new record after US$582 billion in 2021, with a compound annual growth ra...[Details]
According to news on May 15, Samsung Electronics and SK Hynix are accelerating the development of next-generation semiconductor technology to respond to the needs of applications such as ChatGPT in t...[Details]
At the Apple 2021 WWDC conference held early this morning, Apple officially released macOS Monterey. The new features and characteristics of the new operating system are as follows: General Control...[Details]
The circuit in Figure 1 produces an output voltage that you can measure to determine if the two sine waves are in quadrature. If the output voltage is 0V, the input waves (φ1 and φ2) are in perfect qu...[Details]
To set the system to work in svc privileged mode, we know from the previous learning that this requires setting the CPSR program status register.
In the ARM Architecture Reference Manual.pdf d...[Details]
Integrated technical exchanges
京公网安备 11010802033920号
EEWORLD
