EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-MI2SC376N

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-MI2SC376N Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,

PH1-MI2SC376N Parametric

Parameter NameAttribute value
MakerLumentum Operations LLC
Reach Compliance Codecompli
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Communication standardsGR-253
Connection TypeSC/UPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1552 nm
Nominal optical power output1.122 mW
minimum return loss-27 dB
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
IOTZTB-DK006, a comprehensive RF development board
There are many protocols and boards. The protocols support low-power Bluetooth, ZigBee, Thread and other network applications based on IEEE 802.15.4. Needless to say, the number of boards is one set. ...
littleshrimp Special Edition for Assessment Centres
About MSP430 MCU UART_FIFO sending and receiving
There are 2 programs in total. Program 1 sends: #include #define TXBUF_SIZE 32 /*maximum capacity of transmit FIFO*/ unsigned char TX_BUFF[TXBUF_SIZE]; /*transmit FIFO buffer array*/ unsigned int UART...
火辣西米秀 Microcontroller MCU
Is anyone joining the forum? The stock price surged 797% on the first day, and the market value exceeded 45.5 billion ~ Fudan Microelectronics, a domestic billion-gate FPGA supplier, was listed on the Science and Technology Innovation Board
Shanghai, August 4, 2021 - On August 4, Shanghai Fudan Microelectronics Group Co., Ltd. (stock abbreviation "Fudan Microelectronics", stock code "688385") was listed on the Science and Technology Inno...
nmg Domestic Chip Exchange
What's wrong with the xl6019 output voltage being equal to the input voltage? There are pictures.
[i=s]This post was last edited by dahe2005 on 2022-3-8 14:33[/i]I have made a boost board, using XL6019E1, input 12V, output 11.7V, I can't find the reason. Can someone help me analyze it?...
dahe2005 Switching Power Supply Study Group
The evaluation information is here! The Intelligence Bureau wishes all female compatriots a happy holiday~~
La la la ~ Today is a happy day, we can celebrate the festival and read intelligence ~ Here, the members of the Intelligence Bureau wish all female compatriots a happy holiday ~~ Don't forget to read ...
okhxyyo Special Edition for Assessment Centres
TI C66x DSP Instruction Set - ADDKPC
[size=4]The function of the ADDKPC instruction is to save the return address and execute the nop instruction with one instruction. Before calling the B instruction to actually jump, the address of the...
Aguilera Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号