EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

RN1/2T142.20.5%R

Description
Fixed Resistor, Metal Film, 0.5W, 42.2ohm, 350V, 0.5% +/-Tol, 100ppm/Cel, Through Hole Mount, AXIAL LEADED
CategoryPassive components    The resistor   
File Size108KB,2 Pages
ManufacturerSEI(Stackpole Electronics Inc.)
Websitehttps://www.seielect.com/
Download Datasheet Parametric View All

RN1/2T142.20.5%R Overview

Fixed Resistor, Metal Film, 0.5W, 42.2ohm, 350V, 0.5% +/-Tol, 100ppm/Cel, Through Hole Mount, AXIAL LEADED

RN1/2T142.20.5%R Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerSEI(Stackpole Electronics Inc.)
package instructionAXIAL LEADED
Reach Compliance Code_compli
ECCN codeEAR99
Other featuresPRECISION
structureFlame Retard
JESD-609 codee0
Lead diameter0.65 mm
Lead length28 mm
Manufacturer's serial numberRN
Installation featuresTHROUGH HOLE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package diameter3.25 mm
Package length8.75 mm
Package shapeTUBULAR PACKAGE
Package formAxial
method of packingTR
Rated power dissipation(P)0.5 W
Rated temperature70 °C
resistance42.2 Ω
Resistor typeFIXED RESISTOR
seriesRN1/2(100TC,.5%)
surface mountNO
technologyMETAL FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb)
Terminal shapeWIRE
Tolerance0.5%
Operating Voltage350 V
How is the storage period of components calculated?
Let's first use the following figure to understand the classification of components :Definition of storage period of components: Storage period ts : The time components are stored under certain enviro...
火辣西米秀 Analogue and Mixed Signal
Mifare card reader development experience
It seems that more and more people in the forum are interested in this. My first card reader was developed using CM200. There is nothing special about the hardware development. CM200 has an internal a...
tmily RF/Wirelessly
LGA-12 package soldering issues
请问,LGA-12封装芯片贴上PCB板子后,发现个别芯片脱落,而芯片的焊盘粘在PCB板子上,也就是说,芯片跟芯片的焊脚分开了。请问有谁知道这是什么原因引起的麽?...
xinapak TI Technology Forum
PCB Design
I used Altium Designer to draw a PCB. After updating the schematic, I imported it into the PCB. Why did the components I had placed before move to other locations? The schematic was drawn in multiple ...
hql724914 PCB Design
Impedance matching and the basic principles of the Smith chart
[size=4] When dealing with practical application problems of RF systems, there are always some very difficult tasks, and matching the different impedances of the cascaded circuits is one of them. In g...
Jacktang RF/Wirelessly
How to use the new version of single bus driver and DS18x20
The new version of mpy has made significant changes to the single bus driver, making the previous programs unusable. Even if you use the old DS18X20 driver, it cannot be used under the new firmware. H...
dcexpert MicroPython Open Source section

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号