EEWORLDEEWORLDEEWORLD

Part Number

Search

WSFP10133601C

Description
RES,SMT,THIN FILM,33.6K OHMS,100WV,.2% +/-TOL,-100,100PPM TC,0202 CASE
CategoryPassive components    The resistor   
File Size84KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

WSFP10133601C Overview

RES,SMT,THIN FILM,33.6K OHMS,100WV,.2% +/-TOL,-100,100PPM TC,0202 CASE

WSFP10133601C Parametric

Parameter NameAttribute value
MakerVishay
package instructionSMT, 0202
Reach Compliance Codeunknow
ECCN codeEAR99
structureChi
Manufacturer's serial numberSFP
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.558 mm
Package formSMT
Package width0.558 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-STD-883
resistance33600 Ω
Resistor typeFIXED RESISTOR
seriesSFP
size code0202
technologyTHIN FILM
Temperature Coefficient-100,100 ppm/°C
Tolerance0.2%
Operating Voltage100 V
SFP
Vishay Electro-Films
CHIP
RESISTORS
Thin Film Top-Contact Resistor
with Part Mark
FEATURES
Wire bondable
Product may not
be to scale
Part marked - 5 digits
Small size: 0.022 inches square
Resistance range: 1
Ω
to 1 MΩ
DC power rating: 250 mW
Oxidized silicon substrate for good power dissipation
Resistor material: Tantalum nitride, self passivating
Moisture resistant
The SFP series single-value resistor chips offer a small size,
wide ohmic value range and excellent power capacity.
The SFPs are part marked with resistance value allowing
user the ability to visually determine the resistance value of
the chip.
The SFPs are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology.
The SFPs are 100 % electrically tested and visually
inspected to MIL-STD-883.
APPLICATIONS
Vishay EFI SFP small resistor chips are widely used in hybrid packages where space is limited and chip value marking is
important for identification. The die is part marked with the resistance value. Wire bonding is made to the two pads on the top of
the chip.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES
Tightest Standard Tolerance Available
1%
0.5 %
PROCESS CODE
0.1 %
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
± 250 ppm/°C
CLASS H*
103
102
101
100
CLASS K*
108
107
106
105
1
Ω
10
Ω
30
Ω
100
Ω
200 k
Ω
430 k
Ω
620 k
Ω
1 M
Ω
* MIL-PRF-38534 inspection criteria
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
Noise, MIL-STD-202, Method 308
100
Ω
- 250 kΩ
< 100
Ω
or > 251 kΩ
Moisture Resistance, MIL-STD-202
Method 106
Stability, 1000 h, + 125 °C, 125 mW
Operating Temperature Range
Thermal Shock, MIL-STD-202,
Method 107, Test Condition F
High Temperature Exposure, + 150 °C, 100 h
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
Values above 1M available
www.vishay.com
40
For technical questions, contact: ff2bresistors@vishay.com
Document Number: 61000
Revision: 07-Mar-08
- 35 dB typ.
- 20 dB typ.
± 0.5 % max.
ΔR/R
± 0.25 % max.
ΔR/R
- 55 °C to + 125 °C
± 0.25 % max.
ΔR/R
± 0.5 % max.
ΔR/R
200 V
10
12
min.
100 V max.
250 mW
± 0.25 % max.
ΔR/R
DSP Learning (1) Introduction to Digital Signal Processors (DSPs)
Chapter 1 Introduction to Digital Signal Processors (DSPs)Real-time signal processing systems must be able to process large amounts of data to ensure the real-time performance of the system; secondly,...
Aguilera DSP and ARM Processors
【Portable Environmental Status Detector】RTC Electronic Clock
In the design of portable environmental status detector, the detected environmental status needs to be time-calibrated, which can be achieved through the built-in RTC clock of ESP32 S2. When combined ...
jinglixixi DigiKey Technology Zone
Espressif's ESP32-C3 is an extremely low-power SoC equipped with a RISC-V 32-bit single-core processor
ESP32-C3 is an extremely low-power SoC equipped with a RISC-V 32-bit single-core processorESP32-C3-DevKitM-1 Development Board ESP32-C3-DevKitM-1 is an entry-level development board that uses the ESP3...
火辣西米秀 Domestic Chip Exchange
Please teach me a resistance measurement circuit
The circuit schematic is shown in the figure above. P16 is connected to the negative plate. This circuit is used to measure the resistance value. When the resistance value of P16 is different, the wav...
yaoyong Integrated technical exchanges
Why does the STACK MODE of almost all pads in ALTIUM DESIGNER change to FULL STACK?
It used to work fine before, but I don't know since when, all the multi-layer pads in the PCB library became FULL STACK, resulting in a pad on the top layer and a hole on the bottom layer. I checked o...
littleshrimp PCB Design
【STM32WB55 Review】——by Beifang
[url=home.php?mod=space&uid=753718][font=微软雅黑][size=4]@北[/size][/font][/url][font=微软雅黑][size=4] [/size] [/font][url=https://en.eeworld.com/bbs/thread-1075985-1-1.html][font=微软雅黑][size=4]【 STM32WB55 Ev...
okhxyyo RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号