PH1-TS2SC3481 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wireless rf/communication> Optical fiber> PH1-TS2SC3481

PH1-TS2SC3481: DescriptionTransponder, 10660Mbps(Tx), 10660Mbps(Rx), SC/UPC Connector,; CategoryWireless rf/communication Optical fiber; File Size240KB，6 Pages; ManufacturerJDS Uniphase Corporation ( VIAVI ); Websitehttp://www.jdsu.com/index.html

Download Datasheet Parametric View All

PH1-TS2SC3481 Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), SC/UPC Connector,

PH1-TS2SC3481 Parametric

Parameter Name	Attribute value
Maker	JDS Uniphase Corporation ( VIAVI )
Reach Compliance Code	compli
Other features	IT ALSO OPERATE FROM 1280NM TO 1600NM
body height	13.2 mm
Body length or diameter	84.1 mm
Communication standards	GR-253
Connection Type	SC/UPC CONNECTOR
Data rate (receive)	10660 Mbps
Data rate (send)	10660 Mbps
Fiber optic equipment types	TRANSCEIVER, TRANSPONDER
Nominal operating wavelength	1546 nm
Nominal optical power output	0.562 mW
minimum return loss	-27 dB

Preview

Download Datasheet

View All

COMMUNICATIONS MODULES & SUBSYSTEMS

10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder

PH1 Series

Key Features

• Three configurations supporting SR2/IR2/LR2 applications

• Supports dense wavelength division multiplexing

(DWDM) applications (without wavelocker)

• Microprocessor controls to support I2C

• Integrated 16:1/1:16 mux/demux

• Small form factor package (2.2" x 3.0" x 0.53") for high

density applications

• Low power consumption: 4.8 W typical, 6.8 W maximum

for TDM applications

• 70 °C maximum operating temperature

• High sensitivity PIN or APD receivers

• SONET, FEC, Ethernet and Multirate Capable Versions

• Forward, counter and line timing clocking modes

Applications

•

Telecommunications

Metropolitan Area Networks

Subscriber loop

Intra-office SONET/SDH

High bit-rate data communications

JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system

applications with reaches of up to 80 km. The series includes three different

transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM

applications. Each transponder accepts 16 bits of parallel digital data and converts

it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ

modulated optical signal and converts it into 16 bit wide parallel digital data.

The PH1 series offers low DC power dissipation and is available in either a small

form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53

inches) package, depending on system thermal performance requirements. The

transmit design uses an Electro-Absorptive Modulated Laser (EML) which,

depending on the configuration, produces an average output power of between

-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm

typical sensitivity) receiver is available, based on system configurations.

JDSU PH1 Series transponders are designed to support the following data rates:

9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),

10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.

Compliance

• Telcordia GR-253-Core

NORTH AMERICA

800 498-JDSU (5378)

WORLDWIDE

+800 5378-JDSU

WEBSITE

www.jdsu.com

Recommended Resources

ASIL-D Compliant Single-Chip Battery Monitor IC Overview

Buck circuit diagram composed of AP3003

Adaptive DC Regulator

AM demodulator circuit diagram

High stability power supply circuit diagram using LM317

Single-phase half-wave resistive load rectifier circuit

Prize-winning quiz | Bringing life to buildings ADI Building Smoke Detection Technology: Smart building technology is evolving to transform static buildings into dynamic, efficient entities. This evolution requires the use of multiple technologies to monitor more conditions in buildings. ...; EEWORLD社区 Security Electronics

In a bus communication system, how to automatically assign addresses to slaves.: In a bus communication system, how to automatically assign addresses to slaves.At present, the address setting of the slave is done by hardware: DIP switch. Is there a simple method to automatically a...; pcf2000 Domestic Chip Exchange

What parameters should I look at when selecting a TVS? Can anyone tell me?: Experts, what parameters should I consider when selecting TVS? I am confused by the following parameters. What parameters should I consider when selecting? Can an expert tell me?...; 小太阳yy Analog electronics

Are flow and reflow the same thing?: Are flow and reflow the same thing? Why are the standards different? In addition, when designing a PCB, can a trace be routed between two pads of a component? What are the adverse effects of routing a...; 小太阳yy PCB Design

What every electronics engineer should know about oscilloscopes: Of all the test equipment that electronics engineers and technicians have at their disposal, the most useful is undoubtedly the oscilloscope. Oscilloscopes are powerful tools that allow electronics en...; Micsig麦科信 Integrated technical exchanges

Hot Must-Read丨20 Questions and Answers from Data Converters (ADI): ADI has compiled the[20 wonderful questions and answers] in the precision converter area in recent months for everyone. I hope you can use it~Click to view【Wonderful QA】FAQ ● About the hardware circui...; EEWORLD社区 Power technology

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components