EEWORLDEEWORLDEEWORLD

Part Number

Search

WCTQ10033600C

Description
RES NET,THIN FILM,3.36K OHMS,200WV,.2% +/-TOL,-50,50PPM TC,0303 CASE
CategoryPassive components    The resistor   
File Size98KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance  
Download Datasheet Parametric View All

WCTQ10033600C Overview

RES NET,THIN FILM,3.36K OHMS,200WV,.2% +/-TOL,-50,50PPM TC,0303 CASE

WCTQ10033600C Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerVishay
package instructionSMT, 0303
Reach Compliance Codeunknown
ECCN codeEAR99
structureChip
Manufacturer's serial numberCTQ
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.06 W
GuidelineMIL-STD-883
resistance3360 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesCTQ
size code0303
Temperature Coefficient-50,50 ppm/°C
Tolerance0.2%
Operating Voltage200 V
CTQ
Vishay Electro-Films
Thin Film Center-Tapped Resistors
CHIP
RESISTORS
FEATURES
Product may
not be to scale
Wire bondable
Center tap feature
Chip size: 0.030 inches square
Resistance range total: 10
Ω
to 1 MΩ
Resistor material: Tantalum nitride, self-passivating
Moisture resistant
Quartz substrate
Low shunt capacitance < 0.1 pF
I
V
The CTQ series resistor chips offer a wide resistance range with
lower shunt capacitance than can be offered with the silicon
based resistors but only at a lower power level.
The CTQ offers the designer flexibility in use as either a
single value resistor or as two resistor with a center tap
feature. The CTQs six bonding pads allows the user
increased layout flexibility.
The CTQs are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology. The CTQs are 100 % electrically tested and
visually inspected to MIL-STD-883.
R
A
R
B
V
I
V
APPLICATIONS
The CTQ center-tapped resistor chips are used mainly in feedback circuits of amplifiers where ratio matching, low shunt
capacitance and tracking between two resistors is critical.
For low values, the resistance of the six bonding pad configuration can vary, depending on the method of measurement used.
Vishay EFI measures low-value resistors by the four-wire kelvin technique.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES
Tightest Standard Tolerance Available
0.5 %
0.1 %
PROCESS CODE
CLASS H*
CLASS K*
132
130
131
102
100
101
*MIL-PRF-38534 inspection criteria
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
10
Ω
25
Ω
100
Ω
360 kΩ 620 kΩ 1 MΩ
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
TCR Tracking Between Halves (R
A
,
R
B
)
Center Tap Ratio,
R
A
/R
B
: Tolerance
Noise, MIL-STD-202, Method 308, 100
Ω
- 250 kΩ
< 100
Ω
or > 251 kΩ
Moisture Resistance, MIL-STD-202, Method 106
Stability, 1000 h, + 125 °C, 30 mW
Operating Temperature Range
Thermal Shock, MIL-STD-202, Method 107, Test Condition F
High Temperature Exposure, + 150 °C, 100 h
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
*5 ppm/°C for
R
< 100. 20 ppm/°C for
R
< 20
www.vishay.com
82
For technical questions, contact: efi@vishay.com
Document Number: 61030
Revision: 13-Mar-08
± 2 ppm/°C*
1 ± 1 % standard
- 35 dB typ.
- 20 db typ.
± 0.5 % max.
ΔR/R
± 0.25 % max.
ΔR/R
- 55 °C to + 125 °C
± 0.1 % max.
ΔR/R
± 0.2 % max.
ΔR/R
400 V
10
12
min.
200 V
60 mW
± 0.25 % max.
ΔR/R
%
Research and implementation of 32-bit RISC processor.pdf
Research and implementation of 32-bit RISC processor.pdf...
zxopenljx EE_FPGA Learning Park
Overview of PCB Process DFM Technical Requirements
DFM (Design for Manufacturing) is the core technology of concurrent engineering. Design and manufacturing are the two most important links in the product life cycle. Concurrent engineering is to consi...
中信华 PCB Design
[Xingkong board Python programming learning main control board] Xingkong board + SCI acquisition module work together to read and present sensor data
At DFrobot's autumn conference , a new device was released, the SCI acquisition module, which can be used to collect data from a variety of sensors produced by DFRobot without any programming. Officia...
HonestQiao Embedded System
Can MCx063A achieve DC12V, 1.5A output?
[i=s] This post was last edited by yhye2world on 2018-12-4 17:19 [/i] Can MCx063A be used to achieve a DC12V, 1.5A output? The following figure is a screenshot of the MCx063A switching regulator speci...
yhye2world Power technology
Antenna main parameters (reprinted)
How to make a good PCB board? Everyone knows that making a PCB board is to turn the designed schematic diagram into a real PCB circuit board. Please don't underestimate this process. There are many th...
JasonYoo RF/Wirelessly
[CC1352P Review] The twists and turns of GDB debugging CC1352
The reason was still the problem of my development environment, and I was stubborn to use pure GNU tools (CCS was slow and had problems, and I had applied for IAR license but failed, so I didn't want ...
cruelfox RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号