TP32WW1351844 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Mechanical and electronic products> switch> TP32WW1351844

TP32WW1351844: DescriptionPushbutton Switch; CategoryMechanical and electronic products switch; File Size121KB，6 Pages; ManufacturerAPEM; Environmental Compliance

Download Datasheet Parametric View All

TP32WW1351844 Overview

Pushbutton Switch

TP32WW1351844 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	APEM
Reach Compliance Code	compliant
JESD-609 code	e4
Manufacturer's serial number	TP
Switch type	PUSHBUTTON SWITCH
Terminal surface	Silver (Ag)

Preview

Download Datasheet

View All

TP series

Tiny washable momentary pushbutton switches

Distinctive features and specifications

UG1006-A

❑

Process sealed

• Single piece case

• O-ring seal between actuator and bushing

• Epoxy sealed terminals

❑

Wide variety of contact materials

❑

Same PCB layout as TL, TR and TG tiny switches

ELECTRICAL SPECIFICATIONS

MATERIALS

• Max. current/voltage rating with resistive load :

- gold plated contacts : 0,4VA 20V max. AC or DC

- silver plated contacts : 0,5A 48V max. AC or DC

• Minimum load : 10mA 50mV - 10μA 5VDC

• Contact resistance : 50 mΩ max.

• Insulation resistance : 1.000 MΩ min. at 500VDC

• Dielectric strength :

1.000 Vrms 50 Hz min. between terminals and frame

500 Vrms 50 Hz min. between terminals

• Electrical life at full load :

- gold plated contacts : 60.000 cycles

- silver plated contacts : 20.000 cycles

• Case : PBT

• Actuator : polyamide, glass

filled

• Contacts and terminals :

: brass, gold plated

: brass, silver plated

: brass, gold plated (1,27

micron gold)

: contact brass, gold plated

+ tin plated terminals

: contact brass, gold plated

(1,27 micron gold) + tin plated

terminals

• Terminal seal : epoxy

GENERAL SPECIFICATIONS

• Total travel :

- function 2 : 1 mm (.039)

- function 3 : 0,8 mm (.031)

• Strength of terminals : pull-out force - 10N max.

• Operating temperature : -30°C to +85°C

• Moisture : 21 days 95 % (NFC 20-603 - IEC 68-2-3)

• Cleaning : solvents or water + detergent

• Wave soldering : 260°C - 5 sec.

B-8

www.apem.com

APEM

Recommended Resources

The structure of a typical pulse delay circuit

The three-phase three-element reactive energy meter is connected to the circuit through the current transformer

Programmable multivibrator circuit diagram

M58481P (TV and camp audio equipment) 30-function infrared remote control receiving circuit

Internal circuit diagram of 5G28 integrated operational amplifier

Will CAT1 seize the NBIOT market and what will the future situation be like?: 1. Today, NB-IoT accounts for half of China's new cellular IoT shipments From the comparative data, we can see that in China's cellular IoT module shipments in 2020, NB-IoT modules accounted for 54% o...; tianwanghulian LED Zone

MSP430FR6989 Timer Analysis: 1. Foreword:The electronics competition is about to start. This is the first year that TI is the organizer. There may be a question that requires the use of TI chips, so I, who am used to 32, have to ...; fish001 Microcontroller MCU

[Jihai M3 core APM32E103VET6S MINI development board] 06. Implement IAP online upgrade function based on Xmodem: APM32E103VET6S has a built-in 512KB FLASH space, and the size of each page is 2KB. We use the USART interface to implement the Xmodem transmission protocol and PC-side software for data transmission, ...; xld0932 Domestic Chip Exchange

How to quickly design an infrared body temperature detector?: Temperature detection is a necessary monitoring system for us at home, in and out of the community or workplace, and when traveling. Infrared thermometers help reduce contact transmission through non-...; Jacktang Microcontroller MCU

[ST NUCLEO-G071RB Review] + Errors in program migration and operation: This is a function for writing characters to LCD5110. It can run normally under SMT32F103, but it can be compiled successfully under STM32G071. However, an error occurs when it is downloaded to the de...; hujj stm32/stm8

How to disable ADC interrupt separately in stm32f030: I configured the adc channel of stm32f030 as timer triggered interrupt mode and enabled the adc interrupt. I added a variable ADC_conver in the interrupt as the interrupt completion flag, but found th...; bigbat stm32/stm8

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components