The AMS1086 series of adjustable and fixed voltage regulators are designed to provide 1.5A output current and to operate
The
down to 1V input-to-output differential. The dropout voltage of the device is guaranteed maximum 1.5V at maximum output
current, decreasing at lower load currents.
On-chip trimming adjusts the reference voltage to 1%. Current limit is also trimmed, minimizing the stress under overload
conditions on both the regulator and power source circuitry.
The AMS1086 devices are pin compatible with older three-terminal regulators and are offered in 3 lead TO-220 package and
3 lead TO-263 (Plastic DD).
ORDERING INFORMATION:
PACKAGE TYPE
3 LEAD TO-220
AMS1086CT
AMS1086CT-1.5
AMS1086CT-2.5
AMS1086CT-2.85
AMS1086CT-3.0
AMS1086CT-3.3
AMS1086CT-3.5
AMS1086CT-5.0
3 LEAD TO-263
AMS1086CM
AMS1086CM-1.5
AMS1086CM-2.5
AMS1086CM-2.85
AMS1086CM-3.0
AMS1086CM-3.3
AMS1086CM-3.5
AMS1086CM-5.0
OPERATING JUNCTION
TEMPERATURE RANGE
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
FRONT VIEW
TAB IS
OUTPUT
3
2
1
PIN CONNECTIONS
FRONT VIEW
FIXED VERSION
1- Ground
2- V
OUT
3- V
IN
ADJUSTABLE VERSION
1- Adjust
2- V
OUT
3- V
IN
TAB IS
OUTPUT
3
2
1
Advanced Monolithic Systems, Inc.
6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1086
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Power Dissipation
Internally limited
Input Voltage
15V
Operating Junction Temperature Range
Control Section
0°C to 125°C
Power Transistor
0°C to 150°C
Storage temperature
- 65°C to +150°C
Soldering information
Lead Temperature (10 sec)
Thermal Resistance
TO-220 package
TO-263 package
300°C
ϕ
JA
= 50°C/W
ϕ
JA
= 30°C/W *
* With package soldering to 0.5in
2
copper area over
backside ground plane or internal power plane
ϕ
JA
can vary
from 20°C/W to
>40°C/W
depending on mounting
technique.
ELECTRICAL CHARACTERISTICS
Electrical Characteristics at I
OUT
= 0 mA, and T
J
= +25°C unless otherwise specified.
Parameter
Reference Voltage
(Note 2)
Output Voltage
(Note 2)
Device
AMS1086
AMS1086-1.5
AMS1086-2.5
AMS1086-2.85
AMS1086-3.0
AMS1086-3.3
AMS1086-3.5
AMS1086-5.0
Conditions
I
OUT
= 10 mA
10mA
≤
I
OUT
≤
1.5A, 1.5V≤ (V
IN
- V
OUT
)
≤
12V
0
≤
I
OUT
≤
1.5A , 3V≤ V
IN
≤
12V
0
≤
I
OUT
≤
1.5A , 4V≤ V
IN
≤
12V
0
≤
I
OUT
≤
1.5A , 4.35V≤ V
IN
≤
12V
0
≤
I
OUT
≤
1.5A , 4.5V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
1.5A , 4.75V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
1.5A , 5V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
1.5A , 6.5V
≤
V
IN
≤
12V
I
LOAD
= 10 mA , 1.5V≤ (V
IN
- V
OUT
)
≤
12V
(V
IN
- V
OUT
) =3V, 10mA
≤
I
OUT
≤
1.5A
V
IN
= 5V, 0
≤
I
OUT
≤
1.5A
V
IN
= 5V, 0
≤
I
OUT
≤
1.5A
V
IN
= 5V, 0
≤
I
OUT
≤
1.5A
V
IN
= 5V, 0
≤
I
OUT
≤
1.5A
V
IN
= 5V, 0
≤
I
OUT
≤
1.5A
V
IN
= 5.25V, 0
≤
I
OUT
≤
1.5A
V
IN
= 8V, 0
≤
I
OUT
≤
1.5A
∆V
OUT
,
∆V
REF
= 1%, I
OUT
= 1.5 A (Note 4)
Min
1.238
1.225
1.485
1.470
2.475
2.450
2.82
2.79
2.970
2.940
3.267
3.235
3.465
3.430
4.950
4.900
Typ
1.250
1.250
1.500
1.500
2.500
2.500
2.850
2.850
3.000
3.000
3.300
3.300
3.500
3.500
5.000
5.000
03
0.6
0.1
0.2
3
6
3
6
3
6
3
6
3
7
3
6
5
10
1.3
Max
1.262
1.270
1.515
1.530
2.525
2.550
2.88
2.91
3.300
3.360
3.333
3.365
3.535
3.570
5.050
5.100
6
10
.03
.04
12
20
12
20
12
20
12
20
15
25
15
25
20
35
1.5
Units
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
mV
mV
%
%
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
V
Line Regulation
Load Regulation
(Notes 2, 3)
AMS1086/-1.5/-2.5/-2.85/
-3.0/-3.3/-3.5/-5.0
AMS1086
AMS1086-1.5
AMS1086-2.5
AMS1086-2.85
AMS1086-3.0
AMS1086-3.3
AMS1086-3.5
AMS1086-5.0
Dropout Voltage
(V
IN
-
V
OUT
)
AMS1086/-1.5/-2.5/-2.85/
-3.0/-3.3/-3.5/-5.0
Advanced Monolithic Systems, Inc.
6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1086
ELECTRICAL CHARACTERISTICS
Electrical Characteristics at I
OUT
= 0 mA, and T
J
= +25°C unless otherwise specified.
Parameter
Current Limit
Minimum Load
Current
Quiescent Current
Ripple Rejection
Device
AMS1086/-1.5/-2.5/-2.85/
-3.0/-3.3/-3.5/-5.0
AMS1086
AMS1086/-1.5/-2.5/-2.85/
-3.0/-3.3/-3.5/-5.0
AMS1086
AMS1086-1.5
AMS1086-2.5
AMS1086-2.85
AMS1086-3.0
AMS1086-3.3
AMS1086-3.5
AMS1086-5.0
Conditions
(V
IN
- V
OUT
) = 5V
(V
IN
- V
OUT
) = 12V (Note 5)
V
IN
≤
12V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 1.5A,
(V
IN
-V
OUT
) = 3V, C
ADJ
=25µF
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 1.5A,
V
IN
= 4.5V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 1.5A,
V
IN
=5.5V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 1.5A,
V
IN
= 6V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 1.5A
V
IN
= 6V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 1.5A
V
IN
= 6.3V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 1.5A
V
IN
= 6.5V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 1.5A
V
IN
= 8V
T
A
= 25°C, 30ms pulse
10mA
≤
I
OUT
≤
1.5A , 1.5V≤ (V
IN
- V
OUT
)
≤
12V
10mA
≤
I
OUT
≤
1.5A , 1.5V≤ (V
IN
- V
OUT
)
≤
12V
Min
1.5
Typ
2.0
5
5
Max
2.8
10
10
Units
A
mA
mA
dB
dB
dB
dB
dB
dB
dB
dB
60
60
60
60
60
60
60
60
75
72
72
72
72
72
72
68
0.008
55
120
0.2
0.5
5
0.04
Thermal Regulation
Adjust Pin Current
Adjust Pin Current
Change
Temperature Stability
Long Term Stability
RMS Output Noise
(% of V
OUT
)
Thermal Resistance
Junction-to-Case
AMS1086
AMS1086
AMS1086
%W
µA
µA
µA
%
T
A
=125°C, 1000Hrs
T
A
= 25°C , 10Hz
≤
f
≤
10kHz
M Package: Control Circuitry/ Power Transistor
T Package: Control Circuitry/ Power Transistor
0.3
0.003
1
%
%
1.5/4.0
1.5/4.0
°C/W
°C/W
Parameters identified with
boldface type
apply over the full operating temperature range.
Note 1:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. For guaranteed specifications and test conditions, see the
Electrical Characteristics
.
The guaranteed specifications apply only for the test conditions listed.
Note 2:
Line and Load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the input/output differential
and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range.
Note 3:
See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction
temperature by low duty cycle pulse testing. Load regulation is measured at the output lead ~1/8” from the package.
Note 4:
Dropout voltage is specified over the full output current range of the device.
Note 5:
Minimum load current is defined, as the minimum output current required to maintain regulation. When (V
IN
- V
OUT
) = 12V the device is guaranteed to
regulate if the output current is greater than 10mA.
Advanced Monolithic Systems, Inc.
6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1086
APPLICATION HINTS
The AMS1086 series of adjustable and fixed regulators are easy
to use and have all the protection features expected in high
performance voltage regulators: short circuit protection and
thermal shutdown.
Pin compatible with older three terminal adjustable regulators,
these devices offer the advantage of a lower dropout voltage,
more precise reference tolerance and improved reference stability
with temperature.
Stability
The circuit design used in the AMS1086 series requires the use of
an output capacitor as part of the device frequency compensation.
The addition of
150
µF
aluminum electrolytic or a 22µF solid
tantalum on the output will ensure stability for all operating
conditions.
When the adjustment terminal is bypassed to improve the ripple
rejection, the requirement for an output capacitor increases. The
value of 22µF tantalum or
150
µF
aluminum covers all cases of
bypassing the adjustment terminal. Without bypassing the
adjustment terminal smaller capacitors can be used with equally
good results.
To ensure good transient response with heavy load current
changes capacitor values on the order of 100µF are used in the
output of many regulators. To further improve stability and
transient response of these devices larger values of output
capacitor can be used.
Protection Diodes
Unlike older regulators, the AMS1086 family does not need any
protection diodes between the adjustment pin and the output and
from the output to the input to prevent over-stressing the die.
Internal resistors are limiting the internal current paths on the
AMS1086 adjustment pin, therefore even with capacitors on the
adjustment pin no protection diode is needed to ensure device
safety under short-circuit conditions.
Diodes between the input and output are not usually needed.
Microsecond surge currents of 50A to 100A can be handled by the
internal diode between the input and output pins of the device. In
normal operations it is difficult to get those values of surge
currents even with the use of large output capacitances. If high
value output capacitors are used, such as 1000µF to 5000µF and
the input pin is instantaneously shorted to ground, damage can
occur. A diode from output to input is recommended, when a
crowbar circuit at the input of the AMS1086 is used. Normal
power supply cycling or even plugging and unplugging in the
system will not generate current large enough to do any damage.
The adjustment pin can be driven on a transient basis
±25V,
with
respect to the output without any device degradation. As with any
IC regulator, none the protection circuitry will be functional and
the internal transistors will break down if the maximum input to
output voltage differential is exceeded.
D1
V
IN
AMS1086
IN
OUT
ADJ
C
ADJ
10µF
V
OUT
R
1
R
2
+
C
OUT
150µF
Overload Recovery
When the power is first turned on, as the input voltage rises, the
output follows the input, permitting the regulator to start up into
heavy loads. During the start-up, as the input voltage is rising,
the input-to-output voltage differential remains small, allowing
the regulator to supply large output currents. A problem can occur
with a heavy output load when the input voltage is high and the
output voltage is low, when the removal of an output short will
not permit the output voltage to recover. The load line for such a
load may intersect two points on the output current curve. In this
case, there are two stable output operating points for the
regulator. With this double intersection, the power supply may
need to be cycled down to zero and brought up again to make the
output recover.
Ripple Rejection
The ripple rejection values are measured with the adjustment pin
bypassed. The impedance of the adjust pin capacitor at the ripple
frequency should be less than the value of R1 (normally 100Ω
to120Ω) for a proper bypassing and ripple rejection approaching
the values shown. The size of the required adjust pin capacitor is
a function of the input ripple frequency. If R1=100Ω at 120Hz
the adjust pin capacitor should be 25µF. At 10kHz only 0.22µF is
needed.
The ripple rejection will be a function of output voltage, in
circuits without an adjust pin bypass capacitor. The output ripple
will increase directly as a ratio of the output voltage to the
reference voltage (V
OUT
/ V
REF
).
Output Voltage
The AMS1086 series develops a 1.25V reference voltage
between the output and the adjust terminal. Placing a resistor
between these two terminals causes a constant current to flow
through R1 and down through R2 to set the overall output
voltage.
Advanced Monolithic Systems, Inc.
6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1086
APPLICATION HINTS
This current is normally the specified minimum load current of
10mA. Because I
ADJ
is very small and constant it represents a
small error and it can usually be ignored.
AMS1086
IN
OUT
ADJ
I
ADJ
50µA
Connected as shown, R
P is
not multiplied by the divider ratio.
Using 16-gauge wire the parasitic line resistance is about 0.004Ω
per foot, translating to 4mV/ft at 1A load current. It is important
to keep the positive lead between regulator and load as short as
possible and use large wire or PC board traces.
Thermal Considerations
The AMS1086 series have internal power and thermal limiting
circuitry designed to protect the device under overload
conditions. However maximum junction temperature ratings
should not be exceeded under continuous normal load conditions.
Careful consideration must be given to all sources of thermal
resistance from junction to ambient, including junction-to-case,
case-to-heat sink interface and heat sink resistance itself. To
ensure safe operating temperatures and reflect more accurately
the device temperature, new thermal resistance specifications
have been developed. Unlike older regulators with a single
junction-to-case thermal resistance specification, the data section
for these new regulators provides a separate thermal resistance
and maximum junction temperature for both the Control Section
and the Power Transistor. Calculations for both temperatures
under certain conditions of ambient temperature and heat sink
resistance and to ensure that both thermal limits are met.
Junction-to-case thermal resistance is specified from the IC
junction to the bottom of the case directly below the die. This is
the lowest resistance path for the heat flow. In order to ensure the
best possible thermal flow from this area of the package to the
heat sink proper mounting is required. Thermal compound at the
case-to-heat sink interface is recommended. A thermally
conductive spacer can be used, if the case of the device must be
electrically isolated, but its added contribution to thermal
resistance has to be considered.
V
IN
V
OUT
V
REF
R1
R2
V
OUT
= V
REF
(1+
R2/R1)+I
ADJ
R2
Figure 1. Basic Adjustable Regulator
Load Regulation
True remote load sensing it is not possible to provide, because the
AMS1086 is a three terminal device. The resistance of the wire
connecting the regulator to the load will limit the load regulation.
The data sheet specification for load regulation is measured at the
bottom of the package. Negative side sensing is a true Kelvin
connection, with the bottom of the output divider returned to the
negative side of the load.
The best load regulation is obtained when the top of the resistor
divider R1 is connected directly to the case not to the load. If R1
were connected to the load, the effective resistance between the
regulator and the load would be:
R
P
x ( R2+R1 ) ,
R1
R
P
= Parasitic Line Resistance
R
P
PARASITIC
LINE RESISTANCE
V
IN
AMS1086
IN
OUT
ADJ
R1*
R
L
R2*
*
CONNECT R1 TO CASE
CONNECT R2 TO LOAD
Figure 2. Connections for Best Load Regulation
Advanced Monolithic Systems, Inc.
6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
1. General framework: realize the communication between MCU and PC.
The PC (USB interface) sends characters, which are converted to RS232 via USB, and then to RS485 via RS232, and then received by the...
Using the Raspberry Pi PICO and CircuitPython system, plus the AMG8833 sensor and TFT screen, you can make a thermal imager.Project website :https://www.recantha.co.uk/blog/?p=20959...
I bought a mobile power board a few days ago. I didn’t think much of it at first, but later I found that the USB A port was quite special. It can be plugged in both ways....
This book introduces the basic structure, working principle, application configuration and sample programs of the TMS320F28335 DSP chip newly launched by TI. The book has 13 chapters. Chapter 1 is an ...
The power consumption of the first entry into stop mode is correct. After being woken up by an external interrupt, the power consumption of the next entry into stop mode is 300uA higher. What is going...
[i=s]This post was last edited by wangran_95 on 2019-12-31 08:47[/i]After using the device, I found that it was hard to find a power supply. There were two boards and two power supplies, so I had to c...
Wireless connection achievement display
Connect both ends of the HDMI cable to NETGEAR Push2TV and an external TV, turn on the power, adjust to HDMI input mode in the TV menu, and the relevant s...[Details]
As people's living standards continue to improve, Bluetooth headsets have gradually entered the lives of ordinary people. In particular, the emergence of TWS true wireless Bluetooth headsets repres...[Details]
Q1. Is there any difference between using virtual software to simulate and this? I have never seen an emulator or used one.
Answer: Virtual software simulation cannot see the actual effect of the dri...[Details]
In the process of electronic system design and debugging, voltage measurement is often an indispensable item in a control or measurement system. For voltage measurement, if it changes within a small d...[Details]
This lecture mainly implements the implementation of usart TX, which is mainly divided into several parts of application 1. Implementation of USART 1 Tx polling (with printf implementation) 2. Im...[Details]
TE Relay Division of TE Connectivity recently launched an innovative small-size power relay for use in photovoltaic inverters of modern photovoltaic power generation systems. PCFN power relays can ...[Details]
1. Introduction
The processing object of 3D chips is objects represented by polygons. There are two advantages of using polygons to represent objects: first, it is direct (although cumbers...[Details]
On June 8, Suzhou Gotech stated on its investor interaction platform that Suzhou Minghao focuses on the accelerometer sensor market; at the same time, the company has business cooperation with Apple ...[Details]
The price and release date of the Xbox Series X have yet to be officially confirmed, but some new information about it has resurfaced today. Interestingly, the price information revealed this time ...[Details]
NASA is studying the factors behind driver fatigue and how new automated technologies can both help and exacerbate the problem. According to the National Highway Traffic Safety Administration (NHTSA)...[Details]
AXPA17850 is a Class AB automotive audio power amplifier launched by Shenzhen Enxin Semiconductor, with a maximum output power of 4x50W (14.4V power supply voltage, 4Ω load) or 4x85W (14.4V power s...[Details]
1. Set lock time 2. Set the frequency division coefficient 3. Set the CPU to asynchronous working mode 4. Set FCLK Understand the clock schematic of the chip and the function of the register Unders...[Details]
Today, as chip capabilities become stronger, the application range of analog and digital hybrid chips and sensors is also becoming wider and wider. According to Semico Research, the number of analo...[Details]
Junan Energy Storage has established industry-university-research cooperation with many well-known domestic universities and research institutions on key technologies of zinc-bromine flow batteries...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
