SMT Inductors, SIMID Series
SIMID 1210−H
B82422H
Size 1210 (EIA) or 3225 (IEC)
Rated inductance 1 to 680
mH
Rated current 61 to 1150 mA
Construction
S
Ferrite drum core
S
Laser−welded winding
S
Flame−retardant encapsulation
Features
S
Very high current handling capability
S
Suitable for reflow soldering acc. JEDEC J−STD 020C
S
lead−free, RoHS−compatible
S
qualified acc. AEC−Q200
Applications
S
Filtering of supply voltages, coupling, decoupling
S
DC/DC converters / switch mode power supplies
S
Automotive electronics
S
Telecommunications
Terminals
S
Electro−plated
S
Base material CuSn6
S
0,4mm Cu; 1−2mm Ag; 5−7mm Sn (lead-free)
Marking
Marking on component:
L value (in
mH)
and tolerance of L value (coded)
Date of manufacture (coded)
Delivery mode
8mm blister tape, reel packing 180mm Ø reel (2000 pcs) or 330mm Ø reel (7500 pcs)
Taping in accordance to IEC 60286−3. For details on taping and packing refer to data book
“Chokes and Inductors” and to Epcos Homepage.
Please read the important notes
at the end of this document
1
B82422−H1*−3−7659
28.06.2006
SMT Inductors, SIMID Series
SIMID 1210−H
B82422H
Dimensional drawing
Layout recommendation
Dimensions (mm)
Reflow soldering
A
2,70
B
1,15
C
1,80
D
4,40
Marking
1) Soldering area, tinned
Technical data and measuring conditions
Electrical specifications at T
A
= 20°C
Rated inductance L
R
Q factor Q
min
Rated current I
R
Measured with impedance analyzer HP 4294A
at frequency f
L
Measured with impedance analyzer HP 4294A
at frequency f
Q
Maximum permissible DC with inductance decrease
DL/L
0
v10%
and temperature increase of
v45K
at
rated temperature of 105°C
Measured with network analyzer HP 8753
measuring current < I
R
55/150/56 to IEC 60068−1
lead-free to IEC 60068−2−58 and
Jedec J−STD 002B / JESD22−B102D
to IEC 60068−2−20 and MIL−STD−202, method 210
2mm (100mm long standard PCB)
Approx. 50mg
B82422−H1*−3−7659
28.06.2006
Self−resonance frequency f
res,min
DC resistance R
max
Climatic category
Solderability
Resistance to soldering heat
Permissible PCB bending
Weight
Please read the important notes
at the end of this document
2
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain
statements about the suitability of our products for
certain areas of application.
These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out
that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a
rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that
in individual cases, a malfunction of passive electronic components
or failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified.
In customer applications
requiring a very high level of operational safety and especially in customer applications in which
the malfunction or failure of a passive electronic component could endanger human life or health
(e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of
suitable design of the customer application or other action taken by the customer (e.g. installation
of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the
event of malfunction or failure of a passive electronic component.
3.
The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements,
some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as “hazardous”).
Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently,
the products described in this
publication may change from time to time.
The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also
reserve the right to discontinue production and delivery of products.
Consequently,
we cannot guarantee that all products named in this publication will always be available.
6.
Unless otherwise agreed in individual contracts,
all orders are subject to the current version of
the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, EPCOS-JONES, Baoke, CeraDiode, CSSP, MLSC, PhaseCap,
PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K, UltraCap,
WindCap are
trademarks registered or pending
in Europe and in other countries. Further
information will be found on the Internet at www.epcos.com/trademarks.
Page 5 of 5
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
