DC1CM1SC datasheet, PDF - EEWORLD Datasheet

DC1CM1SC: DescriptionSnap Acting/Limit Switch, SPDT, Momentary, 1A, 48VDC, 6.5mm, Wire Terminal, Simulated Roller Actuator, Panel Mount,; CategoryMechanical and electronic products switch; File Size407KB，3 Pages; ManufacturerThe Cherry Corporation

Download Datasheet Parametric View All

DC1CM1SC Overview

Snap Acting/Limit Switch, SPDT, Momentary, 1A, 48VDC, 6.5mm, Wire Terminal, Simulated Roller Actuator, Panel Mount,

Parameter Name	Attribute value
Maker	The Cherry Corporation
Reach Compliance Code	compliant
ECCN code	EAR99
Actuator stroke	6.5 mm
Actuator type	SIMULATED ROLLER
body width	6.5 mm
body height	9 mm
Body length or diameter	20 mm
Contact (AC) maximum rated R load	5A@250VAC
Maximum contact current (AC)	5 A
Maximum contact current (DC)	1 A
Contact (DC) maximum rated R load	1A@48VDC
Maximum contact voltage (AC)	250 V
Maximum contact voltage (DC)	48 V
Electrical life	6000 Cycle(s)
JESD-609 code	e4
Manufacturer's serial number	DC
Installation features	PANEL MOUNT
Maximum operating force	0.78 N
Maximum operating temperature	120 °C
Minimum operating temperature	-40 °C
Maximum pre-travel	5 mm
seal	IP67
surface mount	NO
Switch action	MOMENTARY
switch function	SPDT
Switch type	SNAP ACTING/LIMIT SWITCH
Terminal surface	SILVER
Termination type	WIRE

[ST MEMS waterproof pressure sensor LPS27HHW review] + comparison and application between 2 drivers (and final report): [i=s]This post was last edited by jinglixixi on 2021-2-11 01:14[/i]Because the driver of LPS27HHW was blocked, the evaluation process was slowed down. Fortunately, with the guidance and help of the ad...; jinglixixi MEMS sensors

The problem of mutual influence between the operational amplifier voltage follower circuit and the amplifier circuit in parallel: [i=s]This post was last edited by flyriz on 2020-4-23 19:58[/i]Hello everyone, as shown below:An AC input signal is input to the input end of a voltage follower circuit and an amplifier circuit. The p...; flyriz Analog electronics

Help: What is the problem with low output voltage of DCDC circuit?: The DCDC circuit design in the figure below has an input of 20-36V and is required to output 19.5V. When the current reaches more than 350mA, the voltage drops to about 10V. The input power supply is ...; 灞波儿奔 Power technology

4G AD package library free download: [i=s]This post was last edited by Rambo on 2018-8-13 16:54[/i] [font=微软雅黑][size=5]There are official and third-party ones. Very complete. In response to the requests of netizens, several compressed pa...; 兰博 Download Centre

What does CGSN in AT+CGSN stand for? Where can I find the full name table corresponding to the AT command abbreviation?: 1. AT+CGMI gives the module manufacturer's identification.2. AT+CGMM gets the module identification. This command is used to get the supported frequency bands (GSM 900, DCS 1800 or PCS 1900). Whenthe ...; 一沙一世 MCU

Implementation of HPI Boot Mode in TMS320C62x: [size=4] The first step to implement the HPI boot mode of TMS320C62x is to generate the HPI boot DSP code and merge it with the main processor application so that the DSP application can be remotely d...; 灞波儿奔 DSP and ARM Processors

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components