EEWORLDEEWORLDEEWORLD

Part Number

Search

S3L5-RC

Description
SP3T, 1000MHz Min, 12000MHz Max, 2.4dB Insertion Loss-Max, ROHS COMPLIANT, CASE S3
CategoryWireless rf/communication    Radio frequency and microwave   
File Size263KB,2 Pages
ManufacturerAeroflex
Websitehttp://www.aeroflex.com/
Environmental Compliance
Download Datasheet Parametric View All

S3L5-RC Overview

SP3T, 1000MHz Min, 12000MHz Max, 2.4dB Insertion Loss-Max, ROHS COMPLIANT, CASE S3

S3L5-RC Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAeroflex
Reach Compliance Codeunknown
Other featuresSMA-F, TTL COMPATIBLE
Characteristic impedance50 Ω
structureCOAXIAL
Maximum input power (CW)26.99 dBm
Maximum insertion loss2.4 dB
JESD-609 codee4
Maximum operating frequency12000 MHz
Minimum operating frequency1000 MHz
Maximum operating temperature85 °C
Minimum operating temperature-55 °C
RF/Microwave Device TypesSP3T
Terminal surfaceGold (Au)
Maximum voltage standing wave ratio2
S3L5 Pin Diode Switch
Single Pole, Three Throw
Absorptive
Features:
Incorporated TTL-compatible driver for
convenient system integration and operates
from +5 V and -15 V DC power supplies.
DC blocks at all RF ports.
Ruggedized construction.
RoHS-compliant versions available.
Hermetic versions available.
Specifications:
Parameter
Frequency Range
Insertion Loss (max)
VSWR (max) 50 ohms
Isolation (min)
Switching Speed (max)
CW RF Power, Operating (max)
Specification
1 – 12
2.4
2.0
70
100
0.5
Units
GHz
dB
ratio
dB
nsec
W
Notes:
DC Bias:
(Standard)
DC Bias:
(-5 option)
DC Bias:
(-12 option)
Control:
+5 V +/-0.5 V @ 120 mA max
-15 V +/-3 V @ 50 mA max
+5 V +/-0.5 V @ 150 mA max
-5 V +/-0.5 V @ 60 mA max
+15 V +/-3 V @ 120 mA max
-15 V +/-3 V @ 50 mA max
TTL 0 = Low Loss
TTL 1 = Isolation
E1 controls J2 – J1
E2 controls J3 – J1
E3 controls J4 – J1
Mechanical Specifications:
Case Style:
Finish:
Bias & Control Pins:
Weight:
Mounting:
S3 Outline
Gold Plate per MIL-G-45204
Chem film per MIL-C-5541
ø0.02” x 0.15” long
35 g max
ø0.10” through holes
(4) places
Absorptive Switch: 50 ohm termination present at J2, J3 and J4
(in isolation mode).
Switching speed is defined as 50% TTL to 90% RF (t-on) and 50%
TTL to 10% RF (t-off).
Screening:
Internal Visual per MIL-STD-883, Method 2017
Temperature Cycle: -65 °C to +100 °C, 10 cycles
Hermetically-sealed switches are fine and gross leak checked per
MIL-STD-883, Method 1014.
Optional High-Rel screening available upon request. Contact the
factory to discuss your screening requirements.
Environmental Specifications:
MIL-E-5400, MIL-STD-202, MIL-E-16400
Operating Temp:
-55 °C to +85 °C
Storage Temp:
-65 °C to +125 °C
Humidity:
MIL-STD-202F, M103, Cond B
Shock:
MIL-STD-202F, M213, Cond B
Altitude:
MIL-STD-202F, M105, Cond B
Vibration:
MIL-STD-202F, M204, Cond B
Thermal Shock:
MIL-STD-202F, M107, Cond A
Temperature Cycle:
MIL-STD-202F, M105C, Cond D
SIGNAL & CONTROL SOLUTIONS
Revision Date: 2/11/2014
40 Industrial Way East, Eatontown , NJ 07724 [USA]
Phone: (732) 460-0212, Fax: (732) 460-0214
www.aeroflex.com/ASCS, email: ascs-sales@aeroflex.com
What is output impedance? What is impedance matching?
1. Output Impedance Before understanding the issue of "impedance matching", let us first learn what "output impedance" is? In actual circuit design, whether it is a signal source, amplifier or power s...
火辣西米秀 Analogue and Mixed Signal
[Unboxing and document display of the ACM32F070 capacitive touch development board]
Since I just came back from abroad to work in China (at a certain chip), EEWORLD did not bind a domestic mobile phone number, so I just relied on checking my personal message center every day to check...
JohnMatthrew Domestic Chip Exchange
【GD32L233C-START Review】 Extra 1 Solution to download problems
[i=s]This post was last edited by yang_alex on 2022-2-17 22:50[/i]After compiling the program on the GD32L233C-START evaluation board, the following error message box pops up during downloading. Oops!...
yang_alex GD32 MCU
How to make a jumper between the pads of two different plug-ins in PCB?
How to make a jumper between the pads of two different plug-ins in PCB? As shown in the figure, how to set a jumper between J1 and J2?...
yjguohua PCB Design
"Core" ecosystem, "Assist" security, "Connect" the future. Registration for the 2021 STM32 China Summit and Fan Carnival is now open!
Registration for the 2021 STM32 China Summit and Fan Carnival is now open!The fifth STM32 Summit is about to kick off. As an annual industry event, STMicroelectronics will present you with the latest ...
EEWORLD社区 ST Sensors & Low Power Wireless Technology Forum
Critical issues with naked code
After searching online, I couldn't seem to find any information about the STM32 microcontroller not running the critical code of the system. The microcontroller I am using now is STM32L010RBT6. There ...
sfesdm stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号