Easy to check the fillet after soldering is finished.
2) Small, light, rectangular 4-chip network
Area ratio is 65% smaller than that of MNR34, while weight ratio has been cut 75%.
3) High-density mounting
Can be mounted even more densely than four 0603 chips (MCR03), and mounting costs are lower.
4) Compatible with a wide range of mounting equipment.
Squared coners make it excellent for mounting using image recognition machines.
5) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification.
Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with
the product before using or ordering it.
Ratings
Item
Rated power
Conditions
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
100
POWER LOAD (%)
Specifications
0.063W (1 / 16W)
at 70°C
80
60
40
20
0
−55
0
70
100
125
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the limiting element voltage, the voltage rating
is equal to the maximum operating voltage.
E: Rated voltage (V)
E=
P×R
P: Rated power (W)
R: Nominal resistance (Ω)
Nominal resistance
Operating temperature
See Table 1.
−55°C
to
+125°C
Limiting element voltage
50V
Rev.G
1/4
MNR14
Resistors
Jumper type
Resistance
Rated current
Max. 50mΩ
1A
Table 1
Resistance tolerance
Resistance range
(Ω)
Resistance temperature coefficient
(ppm /
°C)
Operating temperature
−55°C
to
+125°C
J (±5%)
F (±1%)
10 to 1M (E24)
10 to 1M (E24)
±200
±100
•Before
using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
Characteristics
Item
Resistance
Variation of resistance
with temperature
Overload
±
(2.0%+0.1Ω)
Guaranteed value
Resistor type
Jumper type
J :
±5%
F :
±1%
Max. 50mΩ
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
JIS C 5201-1 4.8
Measurement :
−55
/
+25
/
+125°C
JIS C 5201-1 4.13
Rated voltage (current)
×2.5,
2s.
Maximum Overload Voltage : 100V
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235±5°C
Duration of immersion : 2.0±0.5s.
JIS C 5201-1 4.18
Soldering condition : 260±5°C
Duration of immersion : 10±1s.
JIS C 5201-1 4.19
Test temp. :
−55°C
to
+125°C
5cyc
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON
−
0.5h : OFF
Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.3
125°C
Test time : 1,000h to 1,048h
JIS C 5201-1 4.29
23±5°C, Immersion cleaning, 5±0.5min.
Solvent : 2-propanol
JIS C 5201-1 4.33
See Table.1
Max. 50mΩ
Solderability
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
±
(1.0%+0.05Ω)
Max. 50mΩ
No remarkable abnormality on the appearance.
±
(1.0%+0.05Ω)
±
(3.0%+0.1Ω)
Max. 50mΩ
Max. 100mΩ
Resistance to
soldering heat
Rapid change of
temperature
Damp heat, steady state
±
(3.0%+0.1Ω)
Endurance at 70°C
±
(3.0%+0.1Ω)
Endurance
±
(1.0%+0.05Ω)
Resistance to solvent
Max. 100mΩ
Max. 100mΩ
Max. 50mΩ
Bend strength of
the end face plating
Max. 50mΩ
±
(1.0%+0.05Ω)
Without mechanical damage such as breaks.
Rev.G
2/4
MNR14
Resistors
Dimensions
(Unit : mm)
0.6±0.15
0.4±0.15
0.3±0.2
Material
1
0.25±0.15
0.3±0.2
1.6±0.1
Resistive element
(Oxide metal thick film)
Silver thick film electrode
Nickel electrode
Sn electrode
Alumina substrate
Overcoating (Resin)
0.3±0.2
103
0.8
3.2±0.1
0.5±0.1
2
3
4
5
6
2
3
4
Cross section A-A'
6
1
5
Cross section B-B'
6 1
∗
Marking may change to the one-character type.
∗∗
Pitch of the upper electrode.
5
Equivalent circuit
R1
R2
R3
R4
R1=R2=R3=R4
Packaging
Reel
Taping
P
0
P
2
P
1
φD
0
E
F
B
0
08
06
04
02
02
04
06
08
W
A
B
D
A
0
Heat crimp cover / Tape
Thick paper (Underside paper tape)
mount
Chip network
resistors
Square punchout hole
T2
C
Label
EIAJ ET-7200B compliant
(Unit : mm)
W
8.0
±
0.3
D
0
F
3.5
±
0.05
P
0
4.0
±
0.1
E
1.75
±
0.1
P
1
4.0
±
0.1
A
0
1.8
±
0.1
P
2
2.0
±
0.05
B
0
3.4
±
0.1
T
2
Max. 1.1
(Unit : mm)
A
B
C
D
φ13±0.2
0
φ180 −3
φ60 +1
0
9
+1.0
0
φ1.5 +0.1
0
Rev.G
3/4
MNR14
Resistors
Part No. Explanation
M N R 1 4
Part No.
E 0 A P
J
Nominal resistance
Resistance code, 3 or 4 digits.
000 denotes jumper type.
Resistance
Resistance
tolerance
code
F
J
:
:
4 digits
3 digits
Resistance tolerance
F
J
±
1%
±
5%
J is also used
for jumper
Packaging Specifications Code
Part No.
MNR14
Code
E0AP
Resistance tolerance
J(
±
5%)
F(
±
1%)
Packaging specifications
Paper tape (4mm Pitch)
Reel
φ180mm
(7in.)
Basic ordering unit (pcs)
5,000
Reel (
φ
180) : JEITA ET-7200B
: Standard product
Rev.G
4/4
Appendix
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM
CO.,LTD.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you
wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM
upon request.
Examples of application circuits, circuit constants and any other information contained herein illustrate the
standard usage and operations of the Products. The peripheral conditions must be taken into account when
designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document. However, should
you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no respon-
sibility for such damage.
The technical information specified herein is intended only to show the typical functions of and examples of
application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or
exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility
whatsoever for any dispute arising from the use of such technical information.
The Products specified in this document are intended to be used with general-use electronic equipment or
devices (such as audio visual equipment, office-automation equipment, communication devices, electronic
appliances and amusement devices).
The Products are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or
malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard against the
possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as
derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your
use of any Product outside of the prescribed scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or system
which requires an extremely high level of reliability the failure or malfunction of which may result in a direct
threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment,
aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no
responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended
to be used for any such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may be controlled under
the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
dBm=10log(Pout/1mW), where Pout is the power value in mW dBmV=20log(Vout /1mV), where Vout is the voltage value in mV dBuV=20log(Vout /1uV), where Vout is the voltage value in uV Conversion relationsh...
Regarding the ADON trigger function of AT403A and ST103, I find this function a bit annoying. The following examples are given to illustrate1. The essence of the ADON trigger functionis indeed the sam...
I captured a CAN waveform that can communicate normally, but found that the waveform has more than 5 consecutive high levels or low levels without a low level or high level inserted. This is inconsist...
This board of Jihai is really, no matter how you look at it, it doesn't look goodThe board is quite smallThe two big pieces on the right really ruin the aesthetics of the board, the Type B port and th...
According to the regulations of China's intelligent network system, China's intelligent network adopts a network system based on service switching point SSP. The network is equipped with service switc...
Variable gain video branch amplifier controlled by electronic circuit
In this application circuit, the LT1228 transconductance amplifier is used, and the gain is adjustable from -12-+8dB. ...[Details]
According to foreign media reports, at the 2021 CES, Panasonic released its latest car wireless mobile phone charger. It is reported that unlike other car wireless mobile phone chargers, Panasonic ha...[Details]
China Energy Storage Network:
Since China launched a new round of power system reform in 2015, the market-oriented reform of power has been steadily and orderly advancing in recent years. A...[Details]
As IoT devices and embedded systems become more and more popular, TinyML, as an emerging machine learning technology, is gaining more and more attention from researchers and developers. TinyML aims...[Details]
Design concept diagram. Image source: Asian Materials Magazine
Scientists from the UK and Japan have successfully created the world's strongest known iron-based superconducting magnet ...[Details]
Overall solution selection and design Plan demonstration and comparison ① Selection of main circuit and adjustment method Solution 1: Switching voltage regulation adjustment The switching regulat...[Details]
Introduction In the Fencar smart car competition where speed determines the superiority, any factor may affect the operation of the car. In order to meet the needs of accurate analysis of variou...[Details]
The STM32 startup code mainly allocates the stack and sets the vector table, and then jumps to the __main function. The specific code segment to jump to is as follows: view plain copy Reset_H...[Details]
LPC2148 is a microcontroller based on a 32/16-bit ARM7 TDMI-S CPU that supports real-time simulation and embedded trace, and has 32kB and 512kB embedded high-speed Flash memory. The 128-bit wide memo...[Details]
4. Software Design The STM32F103ZE microcontroller controls the AD9850 to generate a sine wave with controllable frequency and phase. The frequency is determined by the keyboard and the step size is ...[Details]
On July 26, local time, General Motors announced to the outside world that the Cruise department's business losses in the second quarter reached US$500 million (approximately RMB 3.3 billion), more t...[Details]
The Fukai Semiconductor Project is invested and constructed by Shenzhen Fukai Semiconductor Technology Co., Ltd. The total planned investment of the project is 150 million yuan. After production, the...[Details]
Many years ago, when I was just learning about oscilloscopes, I saw a sentence in English called "Keep an eye on the Sampling Rate". I translated it into "Always be vigilant about the sampling rate". ...[Details]
Why do so many people choose to use permanent magnet motors now? It is because of its energy saving, which can reach about 20%. Today, I will introduce to you the influence of the geometric shape a...[Details]
Asynchronous serial communication requires fewer transmission lines, has high reliability, and has a long transmission distance. It is widely used in data exchange between microcomputers and periph...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
