EEWORLDEEWORLDEEWORLD

Part Number

Search

7042WWABX601U732U1202-U1022

Description
Rocker Switch, DPDT, Momentary, 4A, 30VDC, Solder Terminal, Small Rocker Actuator, Through Hole-right Angle
CategoryMechanical and electronic products    switch   
File Size567KB,14 Pages
ManufacturerAPEM
Environmental Compliance  
Download Datasheet Parametric View All

7042WWABX601U732U1202-U1022 Overview

Rocker Switch, DPDT, Momentary, 4A, 30VDC, Solder Terminal, Small Rocker Actuator, Through Hole-right Angle

7042WWABX601U732U1202-U1022 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerAPEM
Reach Compliance Codecompliant
ECCN codeEAR99
Actuator typeSMALL ROCKER
body width12 mm
body height13.2 mm
Body length or diameter16.8 mm
Contact (AC) maximum rated R load6A@125VAC
Maximum contact current (AC)6 A
Maximum contact current (DC)4 A
Contact (DC) maximum rated R load4A@30VDC
Maximum contact voltage (AC)125 V
Maximum contact voltage (DC)30 V
Electrical life50000 Cycle(s)
Manufacturer's serial number7000
Installation featuresTHROUGH HOLE-RIGHT ANGLE
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
method of packingBULK
sealEPOXY TERMINAL SEALED
surface mountNO
Switch actionMOMENTARY
switch functionDPDT
Switch typeROCKER SWITCH
Termination typeSOLDER
7000 series
Rocker and paddle switches
Distinctive features and specifications
Wide variety of actuators
Many mounting styles for panel or PCB
VDE, UL and CSA approved
ELECTRICAL SPECIFICATIONS
• Current/voltage rating with resistive load :
Contact
Silver A
Silver,
gold plated AD
Brass,
gold plated CD
Maximum
3A 250VAC - 6A 125VAC - 4A 30VDC
3A 250VAC - 6A 125 VAC - 4A 30VDC
Gold plating withstands up to 100mA 30VDC.
0,4 VA at 20VAC or DC
Minimum
50mA 10VDC
10mA 50mV
10µA 5V
10mA 50mV
10µA 5V
Level *
III and IV
I to IV
I and II
D
• For inductive, lamp or capacitive loads, consult factory.
• Initial contact resistance : 10 mΩ
• Insulation resistance : 1.000 MΩ min. at 500VDC
• Dielectric strength :
1.000 Vrms 50 Hz min. between terminals
1.500 Vrms 50 Hz min. between poles
1.500 Vrms 50 Hz min. between terminals and frame
• Contact bounce : 2 ms max.
• Electrical life : 50.000 cycles at full load
* For details, see technical information, end of catalogue.
MATERIALS
GENERAL SPECIFICATIONS
• Case : diallylphthalate (DAP) or
high temperature plastic material
(UL94-V0)
• Actuator : polyamide
• Housing : stainless steel or steel
tin plated
• Bracket : steel, tin plated
• Contacts
A
: silver
AD
: silver, gold plated
CD
: brass, gold plated
• Terminal seal : epoxy
• Mechanical life : 100.000 cycles
• Panel thickness : 1 (.039) to 2,5 mm(.098)
• Operating temperature : -40°C to +85°C
AGENCY APPROVALS
EN 61058-1
For VDE, refer to 57000 series.
Availability
: consult factory for details of approved models.
Marking
: to order switches marked UL or CSA, complete appropriate box of
ordering format.
APEM
www.apem.com
D-23
Compatible with Raspberry Pi pin definition, adaptable to a variety of modules--Milan STM32MP1 development board demonstration
Hello everyone, I am an engineer from Mir, today I will introduce a new Mir board benchmark product: MYD-YA15XC-T. Today's article will be divided into two parts to introduce this board developed base...
blingbling111 ARM Technology
A detail of MSP430 interrupt
About the interrupt flag:Send one byte of data from SPI: void SPI_Set_SD_Byte(unsigned char txData) { UCB0TXBUF = txData; // Write to the transmit bufferwhile ((UCB0IFGUCTXIFG) == 0); // Waiting for s...
fish001 Microcontroller MCU
About "Coupled SEPIC"
The coupling capacitor can be either very small or very large, small enough to only provide clamping for the main switch, or large enough that the voltage at its end is "almost unchanged"; The degree ...
PowerAnts Power technology
Schematic diagram - Is there any difference or consideration between choosing MOS and transistor for Q2 in this power switch circuit?
I saw this circuit diagram on the Internet, which said that it was a problematic circuit and Q1 was prone to burn out. The comments section has the following opinions: 1. The resistance of R7 is too l...
普拉卡图 Analog electronics
ESP8266 adds support for VfsLfs1 and VfsLfs2
ESP8266 adds support for VfsLfs1 and VfsLfs2, which can be added to the firmware via compile switches.make MICROPY_VFS_LFS2=1esp8266/moduos: Add optional support for VfsLfs1 and VfsLfs2. esp8266/modul...
dcexpert MicroPython Open Source section
TI - Signal Chain Design Considerations for Ultrasound Systems
High-performance ultrasound imaging systems are widely used in various medical scenarios. In the past decade, discrete circuits in ultrasound systems have been replaced by highly integrated chips (ICs...
Aguilera Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号