EEWORLDEEWORLDEEWORLD

Part Number

Search

WCTQ1319650AD

Description
RES NET,THIN FILM,965 OHMS,200WV,.5% +/-TOL,-100,100PPM TC,0303 CASE
CategoryPassive components    The resistor   
File Size98KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance  
Download Datasheet Parametric View All

WCTQ1319650AD Overview

RES NET,THIN FILM,965 OHMS,200WV,.5% +/-TOL,-100,100PPM TC,0303 CASE

WCTQ1319650AD Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1178118424
package instructionSMT, 0303
Reach Compliance Codeunknown
ECCN codeEAR99
structureChip
Manufacturer's serial numberCTQ
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.06 W
GuidelineMIL-STD-883
resistance965 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesCTQ
size code0303
Temperature Coefficient100 ppm/°C
Tolerance0.5%
Operating Voltage200 V
CTQ
Vishay Electro-Films
Thin Film Center-Tapped Resistors
CHIP
RESISTORS
FEATURES
Product may
not be to scale
Wire bondable
Center tap feature
Chip size: 0.030 inches square
Resistance range total: 10
Ω
to 1 MΩ
Resistor material: Tantalum nitride, self-passivating
Moisture resistant
Quartz substrate
Low shunt capacitance < 0.1 pF
I
V
The CTQ series resistor chips offer a wide resistance range with
lower shunt capacitance than can be offered with the silicon
based resistors but only at a lower power level.
The CTQ offers the designer flexibility in use as either a
single value resistor or as two resistor with a center tap
feature. The CTQs six bonding pads allows the user
increased layout flexibility.
The CTQs are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology. The CTQs are 100 % electrically tested and
visually inspected to MIL-STD-883.
R
A
R
B
V
I
V
APPLICATIONS
The CTQ center-tapped resistor chips are used mainly in feedback circuits of amplifiers where ratio matching, low shunt
capacitance and tracking between two resistors is critical.
For low values, the resistance of the six bonding pad configuration can vary, depending on the method of measurement used.
Vishay EFI measures low-value resistors by the four-wire kelvin technique.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES
Tightest Standard Tolerance Available
0.5 %
0.1 %
PROCESS CODE
CLASS H*
CLASS K*
132
130
131
102
100
101
*MIL-PRF-38534 inspection criteria
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
10
Ω
25
Ω
100
Ω
360 kΩ 620 kΩ 1 MΩ
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
TCR Tracking Between Halves (R
A
,
R
B
)
Center Tap Ratio,
R
A
/R
B
: Tolerance
Noise, MIL-STD-202, Method 308, 100
Ω
- 250 kΩ
< 100
Ω
or > 251 kΩ
Moisture Resistance, MIL-STD-202, Method 106
Stability, 1000 h, + 125 °C, 30 mW
Operating Temperature Range
Thermal Shock, MIL-STD-202, Method 107, Test Condition F
High Temperature Exposure, + 150 °C, 100 h
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
*5 ppm/°C for
R
< 100. 20 ppm/°C for
R
< 20
www.vishay.com
82
For technical questions, contact: efi@vishay.com
Document Number: 61030
Revision: 13-Mar-08
± 2 ppm/°C*
1 ± 1 % standard
- 35 dB typ.
- 20 db typ.
± 0.5 % max.
ΔR/R
± 0.25 % max.
ΔR/R
- 55 °C to + 125 °C
± 0.1 % max.
ΔR/R
± 0.2 % max.
ΔR/R
400 V
10
12
min.
200 V
60 mW
± 0.25 % max.
ΔR/R
%
Components and electronic products testing
If you have the following testing needs, please contact me. The resources of AVIC 301 Institute include: capacitor testing, component screening, electronic product failure analysis, identification of ...
融融网 DIY/Open Source Hardware
Purgatory Legend-RAM War
Calling and verifying IP core RAM...
雷北城 FPGA/CPLD
ATX-100 Series Cable Harness Tester Revealed! (Demo + Features)
ATX-100 Series Cable Harness Tester Revealed! (Demo + Features)...
aigtekatdz Test/Measurement
Who can give me the control circuit of the car main driver's door glass lifting switch group
Who can give me a control circuit for the car's main driver's door window lift switch group? This switch communicates with the door module LIN. It is found that when there is no LIN signal from the do...
造个时光机器 Automotive Electronics
Reasons why the automatic function of a digital oscilloscope cannot be triggered when measuring low-frequency signals
A friend who uses an oscilloscope said that the automatic function of his oscilloscope was broken and could not be automatically successful. I looked at the video he sent and it was a straight line. A...
Micsig麦科信 Test/Measurement
Running helloworld-porting on iTOP-4418 development board
Transplanting applications based on (Xunwei iTOP-4418 development board)qte Before using qmake, you need to compile the qte source code first, refer to Chapter 7.Continuing from the previous section, ...
塔7呃 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号