EEWORLDEEWORLDEEWORLD

Part Number

Search

54122-113-04-2350LF

Description
Board Connector, 8 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size107KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

54122-113-04-2350LF Overview

Board Connector, 8 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle

54122-113-04-2350LF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompliant
body width0.19 inch
subject depth0.925 inch
body length0.4 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedMatte Tin (Sn) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee3
Manufacturer's serial number54122
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.12 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts8
Base Number Matches1
PDM: Rev:K
STATUS:
Released
Printed: Mar 10, 2011
.
How do I design a circuit with such input and output?
1. There are signals in and out, and there may be a clk. When in changes from low level to high level, out should output high level immediately. No matter how in pin changes, out should not change. Ho...
littleshrimp FPGA/CPLD
Board burning problem
Every time the program of the board is changed, the board must be powered off, then powered on again, and the program must be burned again before it can run. This is inconvenient. Are there any improv...
lzx_18570633112 DSP and ARM Processors
X-NUCLEO-IKS01A3 driver for Arduino
Well, I participated in an event and was given a board for free, but the prerequisite was to debug and port it to an MCU, so I wrote the Arduino UNO. Then after I got it, I found that ST actually wrot...
jianshan ST Sensors & Low Power Wireless Technology Forum
Nexperia Award-winning Live Broadcast: Introduction and Application of Automotive Power MOSFET and GaN Devices in Electric Vehicles
Nexperia Award-winning Live Broadcast: Introduction and Application of Automotive Power MOSFET and GaN Devices in Electric VehiclesClick here to enter the live broadcastLive broadcast time: October 18...
EEWORLD社区 Automotive Electronics
Differences between LDO and DC-DC devices
DCDC means DC to DC (conversion of different DC power values). Any device that meets this definition can be called a DCDC converter, including LDO. However, the general term is that the device that co...
zbz0529 Power technology
Nordic Bluetooth sensor monitors guitar temperature and humidity
Recently launched on the forumDevelopment competition based on ON Semiconductor's low-power Bluetooth chip RSL10, 10,000 yuan gift Some netizens want to participate, but feel that Bluetooth has run ou...
nmg Sensor

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号