Radiation-hardened design; total dose irradiation testing to
MIL-STD-883 Method 1019
- Total-dose: 300 krad(Si) and 1 Mrad(Si)
- Latchup immune (LET > 100 MeV-cm
2
/mg)
Packaging options:
- 48-lead flatpack
Standard Microcircuit Drawing 5962-01534
- QML Q and V compliant part
Compatible with TIA/EIA-644 LVDS standard
INTRODUCTION
The UT54LVDS217 Serializer converts 21 bits of CMOS/TTL
data into three LVDS (Low Voltage Differential Signaling) data
streams. A phase-locked transmit clock is transmitted in parallel
with the data streams over a fourth LVDS link. Every cycle of
the transmit clock 21 bits of input data are sampled and
transmitted.
At a transmit clock frequency of 75MHz, 21 bits of TTL data
are transmitted at a rate of 525 Mbps per LVDS data channel.
Using a 75MHz clock, the data throughput is 1.575 Gbit/s (197
Mbytes/sec).
The UT54LVDS217 Serializer allows the use of wide, high
speed TTL interfaces while reducing overall EMI and cable size.
All pins have Cold Spare buffers. These buffers will be high
impedance when V
DD
is tied to V
SS
.
21
CMOS/TTL INPUTS
TTL PARALLEL-TO-LVDS
TTL PARALLEL -TO-LVDS
DATA (LVDS)
TRANSMIT CLOCK IN
POWER DOWN
PLL
CLOCK (LVDS)
Figure 1. UT54LVDS217 Serializer Block Diagram
1
TxIN4
V
DD
TxIN5
TxIN6
GND
TxIN7
TxIN8
V
DD
TxIN9
TxIN10
GND
TxIN11
TxIN12
V
DD
TxIN13
TxIN14
GND
TxIN15
TxIN16
TxIN17
V
DD
TxIN18
TxIN19
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
UT54LVDS217
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
TxIN3
TxIN2
GND
TxIN1
TxIN0
N/C
LVDS GND
TxOUT0-
TxOUT0+
TxOUT1-
TxOUT1+
LVDS V
DD
LVDS GND
TxOUT2-
TxOUT2+
TxCLK OUT-
TxCLK OUT+
LVDS GND
PLL GND
PLL V
DD
PLL GND
PWR DWN
TxCLK IN
TxIN20
PIN DESCRIPTION
Pin Name
TxIN
TxOUT+
TxOUT-
TxCLK IN
TxCLK
OUT+
TxCLK OUT-
PWR DWN
I/O
I
O
O
I
O
O
I
No.
21
3
3
1
1
1
1
Description
TTL level input
Positive LVDS differential data output
Negative LVDS differential data output
TTL level clock input. The rising edge acts
as data strobe. Pin name TxCLK IN
Positive LVDS differential clock output
Negative LVDS differential clock output
TTL level input. Assertion (low input) TRI-
STATEs the clock and data outputs, ensur-
ing low current at power down.
Power supply pins for TTL inputs and logic
Ground pins for TTL inputs and logic
Power supply pins for PLL
Ground pins for PPL
Power supply pin for LVDS output
Ground pins for LVDS outputs
V
DD
GND
PLL V
DD
PLL GND
LVDS V
DD
LVDS GND
I
I
I
I
I
I
4
5
1
2
1
3
Figure 2. UT54LVDS217 Pinout
UT54LVDS217
TxIN
0
1
2
LVDS CABLE
MEDIA DEPENDENT DATA
(LVDS)
UT54LVDS218
RxOUT
0
1
2
CMOS/
TTL
18
19
20
18
19
20
CLOCK
(LVDS)
TxCLK
GND
PCB
SHIELD
Figure 3. UT54LVDS217 Typical Application
PCB
RxCLK
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
4
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.3 to 4.0V
-0.3 to (V
DD
+ 0.3V)
-65 to +150°C
2W
+150°C
10°C/W
±
10mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175°C during burn-in and lifetest.
3. Test per MIL-STD-883, Method 1012.
4. For cold spare mode (V
DD
= V
SS
), V
I/O
may be 0.3V to the maximum recommended operating V
DD
+ 0.3V.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD,
P
LL
V
DD,
LVDS V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage
LIMITS
3.0 to 3.6V
-55 to +125°C
0V to V
DD
3
DC ELECTRICAL CHARACTERISTICS
1
SYMBOL
PARAMETER
(V
DD
= 3.3V-0.3V; -55°C < T
C
< +125°C)
CONDITION
MIN
MAX
UNIT
CMOS/TTL DC SPECIFICATIONS
V
IH
V
IL
I
IH
I
IL
V
CL
I
CS
High-level input voltage
Low-level input voltage
High-level input current
Low-level input current
Input clamp voltage
Cold Spare Leakage current
V
IN
= 3.6V; V
DD
= 3.6V
V
IN
= 0V; V
DD
= 3.6V
I
CL
= -18mA
V
IN
= 3.6V; V
DD
= V
SS
-20
2.0
GND
-10
-10
V
DD
0.8
+10
+10
-1.5
+20
V
V
µA
µA
V
µA
LVDS OUTPUT DC SPECIFICATIONS (OUT+, OUT-)
V
OD5
∆V
OD5
V
OS5
∆V
OS5
I
OZ4
I
CSOUT
I
OS2,3
Differential Output Voltage
Change in V
OD
between
complimentary output states
Offset Voltage
R
L
= 100Ω (See Figure 14)
R
L
= 100Ω (See Figure 14)
Voh + Vol
-
R
L
= 100Ω,
⎛
Vos = --------------------------
⎞
⎝
⎠
2
250
400
35
mV
mV
V
1.120
1.410
Change in V
OS
between
complimentary output states
Output Three-State Current
R
L
= 100Ω
PWR DWN = 0V
V
OUT
= 0V or V
DD
V
IN
=3.6V, V
DD
= V
SS
V
OUT
+ or V
OUT-
= 0V
-10
35
+10
mV
µΑ
µΑ
mA
Cold Spare Leakage Current
Output Short Circuit Current
-20
+20
5mA
Supply Current
I
CCL4
I
CCZ4,6
Transmitter supply current with
loads
Power down current
R
L
= 100Ω all channels
(figure 4)
CL = 5pF, f = 50MHz
D
IN
= V
SS
PWR DWN = 0V, f = 0Hz
65.0
mA
60.0
µA
Notes:
1. Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground.
2. Output short circuit current (I
OS
) is specified as magnitude only, minus sign indicates direction only. Only one output should be shorted at a time, for a maximum
duration of one second.
3. Guaranteed by characterization.
4. Devices are tested @ 3.6V only.
5. Clock outputs guaranteed by design.
6. Post 100Krad and 300Krad, I
CCZ
= 200µA.
4
AC SWITCHING CHARACTERISTICS
1
(V
DD
= 3.0V to 3.6V; TA = -55°C to +125°C)
SYMBOL
LLHT
2
LHLT
2
TPPos0
2
TPPos1
2
TPPos2
2
TPPos3
2
TPPos4
2
TPPos5
2
TPPos6
2
TCCS
3
TCIP
TCIH
4
TCIL
4
TSTC
2
THTC
2
TCCD
TPLLS
TPDD
PARAMETER
LVDS Low-to-High Transition Time (Figure 5)
LVDS High-to-Low Transition Time (Figure 5)
Transmitter Output Pulse Position for Bit 0 (Figure 13)
Transmitter Output Pulse Position for Bit 1(Figure 13)
Transmitter Output Pulse Position for Bit 2 (Figure 13)
Transmitter Output Pulse Position for Bit 3 (Figure 13)
Transmitter Output Pulse Position for Bit 4 (Figure 13)
Transmitter Output Pulse Position for Bit 5 (Figure 13)
Transmitter Output Pulse Position for Bit 6 (Figure 13)
Channel to Channel skew (Figure 7)
TxCLK IN Period (Figure 8)
TxCLK IN High Time (Figure 8)
TxCLK IN Low Time (Figure 8)
TxIN Setup to TxCLK IN (Figure 8)
TxIN Hold to TxCLK IN (Figure 8)
TxCLK IN to TxCLK OUT Delay (Figure 9)
Transmitter Phase Lock Loop Set (Figure 10)
Transmitter Powerdown Delay (Figure 12)
15MHz
75MHz
15MHz
75MHz
13.3
0.35Tcip
0.35Tcip
1.0
0.5
0.7
0.5
0.5
2.5
10
100
f=75MHz
f=75MHz
f=75MHz
f=75MHz
f=75MHz
f=75MHz
f=75MHz
-0.18
1.72
3.63
5.53
7.44
9.34
11.25
MIN
MAX
1.5
1.5
0.270
2.17
4.08
5.98
7.89
9.79
11.70
0.45
66.7
0.65Tcip
0.65Tcip
UNIT
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
ns
Notes:
1. Recommend transistion time for TXCLK In is 1.0 to 6.0 ns (figure 6).
2. Guaranteed by characterization.
3. Channel to channel skew is defined as the difference between TPPOS max limit and TPPOS minimum limit.
The temperature and humidity integrated digital sensor Si7021 used in our development kit has an I2C interface . The I2C interface sensors on the development board are all mounted on one bus.The bus i...
PD3.0 and QC3.0; total power 120W. One fast charger and two QC3.0 fast chargers at the same time without interference, both are fast chargers, those who are capable can contact me. Payment method, the...
[i=s]This post was last edited by wgy1202 on 2019-3-7 14:05[/i] I am using pic18f26k83, and i2c is in slave mode. When receiving data, it can recognize the address and give ack. However, when receivin...
Toyota Motor Corporation and BYD Co., Ltd. today signed a joint venture agreement to establish a pure electric vehicle research and development company. The new company will be officially established...[Details]
▲When off-road vehicles face rugged terrain, they cannot clearly grasp the road conditions due to the height of the vehicle. Therefore, many models with off-road capabilities will have ground-base...[Details]
ADS7864 is a 12-bit 6-channel A/D converter developed by Burr-Brown. This paper introduces the working principle, internal structure, working mode and programming points of ADS7864. An application ex...[Details]
Discuss the application of motor drivers in the design of white goods solutions such as refrigerators, air conditioners, washing machines and dryers. As the world pays more and more attention to impro...[Details]
Our reporter/Wang Jinlong/Xi'an report
"New infrastructure" is becoming a new "trend" for investment.
Among them, UHV is one of the seven key investment areas of "new infrastructure", and...[Details]
Developing smartphone chipsets is a time-consuming process. Samsung is reportedly using artificial intelligence to design Exynos chipsets, which will be used in the next generation of smartphones fro...[Details]
1 Introduction
Maintenance-free batteries (referred to as batteries) are widely used in electric bicycles, electric tour buses and uninterruptible power supply systems due to their ease of u...[Details]
1. Software Installation
1. First, install the NIOS II development kit. Use virtual CD-ROM software, such as DAEMON, to map the NIOS II V1.0 BUILD316E.ISO file to the virtual CD-ROM....[Details]
On January 15, according to MacRumors, Bloomberg reporters Mark Gurman and Debby Wu said last year that Apple had tested a new iPad Pro with a glass back to support wireless charging. In a rece...[Details]
1.1 Design Principle Frequency is the number of times a periodic signal changes within a unit time (1s). If the number of repeated changes of this periodic signal measured within a certain time inte...[Details]
In banks or other public places, you often see displays showing real-time information, including year, month, day, week, time, etc. The function of this example is to set, obtain, and record real-tim...[Details]
The working principle of the series motor is the same as that of the DC motor, and the left-hand rule and the right-hand rule can fully explain its principle.
The principle of the series...[Details]
On April 21, Eaton Electronics released its 2020 performance report, stating that the company achieved operating income of 2.451 billion yuan, a year-on-year decrease of 18.59%; the net profit attrib...[Details]
New 256GB, 512GB and 1TB Flash Devices Allow Smartphones and Mobile Apps to Take Advantage of High-Speed 5G Networks
Continuing to advance the development of Universal Flash Storag...[Details]
In digital circuit systems, square waves are frequently used signal sources with a very wide range of applications. In ordinary circuit design, 555 timers are often used to form multivibrators to g...[Details]
Development Kits Review Area
京公网安备 11010802033920号
EEWORLD
