MN08D0850 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The connector> The connector> MN08D0850

MN08D0850: DescriptionRF N Connector, Cable Mount; CategoryThe connector The connector; File Size194KB，1 Pages; ManufacturerMethode Electronics Inc.

Download Datasheet Parametric View All

MN08D0850 Overview

RF N Connector, Cable Mount

MN08D0850 Parametric

Parameter Name	Attribute value
Maker	Methode Electronics Inc.
Reach Compliance Code	unknown
Other features	APPLICABLE CABLES:RG 6; RG 6A; RG 143; RG 212
Characteristic impedance	50 Ω
Connector type	RF N CONNECTOR
Contact to complete cooperation	NOT SPECIFIED
Coupling type	THREADED
DIN compliance	NO
Filter function	NO
IEC compliance	NO
insulator material	DELRIN
MIL compliance	NO
Manufacturer's serial number	N
Installation method	STRAIGHT
Installation type	CABLE
Maximum operating frequency	4 GHz
Panel mounting	NO
voltage standing wave ratio	1.2
Base Number Matches	1

Preview

Download Datasheet

View All

Our years of experience translates to immediate support for

™

existing or new project development. Continued commitment

to technological advancement assures our customers access

to the latest developments available.

N Series

Applications:

Transmitters and Receivers, Broadcast Equipment, Antenna,

LANs, Test and Measurement

*Electrical Specifications:

Voltage Rating:

Withstanding Voltage:

Insulation Resistance:

Contact Resistance:

VSWR:

Frequency Range:

Impedance:

AC 500V

AC 1000V one minute

1000 MΩ min at DC 500V

3 mΩ max at DC 1A

1.2 max 0-4 GHz

0-4000 MHz

50 Ohm

DIN 7/16 Series

Applications:

Broadcast Communications, Control Components, Cellular Base

Stations, Jumper Cables

*Electrical Specifications:

Voltage Rating:

Withstanding Voltage:

Insulation Resistance:

Contact Resistance:

VSWR:

Frequency Range:

Impedance:

2.7 kV RMS

4 kV RMS

10 GΩ min

8 mΩ After Conditioning

1.02 max 0-7 GHz

DC-7 GHz

50 Ohm

UHF Series

Applications:

CB Radios, Antennas, Public Address Systems, Landing Systems,

Ground Control Apparatus

*Electrical Specifications:

Voltage Rating:

Withstanding Voltage:

Insulation Resistance:

Contact Resistance:

Frequency Range:

Impedance

AC 500V

AC 1000V one minute

1000 MΩ min at DC 500V

3 mΩ max at DC 1A

0-300 MHz

Non-Constant

*These characteristics are typical and may not apply to all connectors

9 0 9 R a h w a y A v e . , U n i o n , N J 0 7 0 8 3 - 5 4 9 1 . Te l : 9 0 8 . 6 8 8 . 8 0 0 0 . F a x : 9 0 8 . 6 8 8 . 8 0 5 3 . E m a i l : I n f o @ m e t h o d e r f . c o m

Recommended Resources

One of the resistance furnace relay temperature control circuits

Switching power supply circuit diagram---positive and negative 5V output, positive and negative 12V output

Simple charger circuit 01

Microcurrent-voltage conversion circuit

PLL circuit using M51728L

NE5565 electronic ballast controller

Importance of CMTI parameter for isolation driver selection: What is CMTI ? CMTI, Common mode transient immunity, is one of the most important indicators of isolation products (including iCoupler digital isolators and optocouplers). CMTI common mode transient i...; alan000345 TI Technology Forum

Gold - Sand - Wafers - Artwork - Qorvo Semiconductor: [i=s]This post was last edited by btty038 on 2019-10-16 09:04[/i]...; btty038 RF/Wirelessly

Programmable sensor-specific detection MCU CS88F313: The CS88F313 is a low-power programmable sensor-specific detection circuit with ADC function. It can be used in electronic measuring instruments, environmental monitoring, handheld measuring tools, ho...; 虹芯侠客 51mcu

[National Technology N32G457 Review] 4. PWM and breathing light test: My related posts: [National Technology N32G457 Review] 1. Data Preparation [National Technology N32G457 Review] 2. Unboxing + Lighting [National Technology N32G457 Review] III. ADC and Serial Port Fun...; fxyc87 Domestic Chip Exchange

【GD32L233C-START Review】 Extra 1 Solution to download problems: [i=s]This post was last edited by yang_alex on 2022-2-17 22:50[/i]After compiling the program on the GD32L233C-START evaluation board, the following error message box pops up during downloading. Oops!...; yang_alex GD32 MCU

How to make a jumper between the pads of two different plug-ins in PCB?: How to make a jumper between the pads of two different plug-ins in PCB? As shown in the figure, how to set a jumper between J1 and J2?...; yjguohua PCB Design

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components