DTerminator 2 PTB/PTX/PTP
Pedestal Terminal Blocks
•
•
•
•
GelGuard gel sealing technology
Versatile mounting system
Protection can be added as needed
Environmentally sealed protection
The DTerminator 2 PTB/PTX/PTP pedestal-
mounted terminal block systems utilize Tyco
Electronics’ revolutionary GelGuard gel sealing
technology to environmentally protect the wire
connections. Three models have been designed.
The DTerminator 2 PTB terminal block offers
enhanced characteristics with a versatile
mounting system suitable for attachment to
any pedestal faceplate. This model cannot
be protected.
The DTerminator 2 PTX upgradable terminal
block includes a grounding strip. Although it is an
unprotected model, the PTX driver modules can
be easily replaced in the field with protected
driver modules, creating a protected pair unit
when needed.
The DTerminator 2 PTP protected terminal block
contains driver modules with environmentally
sealed circuit protectors. Each connection is
protected by a three-element gas discharge tube.
TELECOM OUTSIDE PLANT
Product Information
• Tyco Electronics’ unique IIDC (inverted
insulation displacement connector)
accommodates 18 - 24 AWG (1.02 - .51 mm)
wires without requiring wire stripping or
special tools.
• Patented GelGuard gel sealing technology
provides superior performance and is
specifically formulated for environmentally
demanding terminal applications.
• An audible click indicates when the driver is
properly seated for wire insertion.
• A single bolt terminates each pair into a
driver module through which the connection
is visible.
• A single drop wire port further simplifies
installation by eliminating the chance of
placing the drop wire in the wrong port.
• Gel-protected test ports in the top of each
driver module facilitate fast, easy testing
with standard test clips.
• DTerminator 2 products are available in a
wide range of pair counts. Protected and
unprotected blocks of the same pair count
are the same size but different colors. See
ordering information below.
• DTerminator 2 terminals are UL Listed for
Indoor/Outdoor use when installed in a
suitably approved UL Listed enclosure
including units mounted on or inside a
building. Terminal blocks mounted in a
restricted access area inside a building do
not require an enclosure.
• Blocks are available in an upgradable design,
allowing for protection to be added when
needed on a pair by pair basis, saving
unnecessary initial cost.
• Driver modules can be re-entered and
re-sealed many times, even after prolonged
exposure to temperature extremes.
• Special circuit markers are available for easy
identification of special lines.
• Compliant with Telcordia specification
TR-NWT-000975 and TR-NWT-001305.
DT2-PTB-XX XXXXF - XDX - XX
Model
B - Unprotected
X - Upgradable
P - Protected
Pair Count
5, 6, 10, 12, 15, 25 and 50-pair
Cable Type
AS - Aircore shielded
AU - Aircore unshielded
FS - Filled shielded
FU - Filled unshielded
VT - PVC tip-tracer
Cable Length
04 - 4 ft. (AU/VT only)
06 - 6 ft. (FU only)
12 - 12 ft.
25 - 25 ft.
Block Printing
0 - No printed numbers
1 - T/R
2 - A/B
Driver Type
1 - FS 265-600V 24 AWG, blue
2 - VS/FS 265-600V 24 AWG, lt. blue
3 - Unprotected 24 AWG, white
Note: Fail Safe only for OSP
Applications. Fail Safe/Vent Safe
for primary protection.
Description Key is to assist with interpreting
product configuration. Not all configurations
are available. Contact Customer Service
regarding availability.
Drop Entry
R - Right
L - Left
B - Both (Available in 25 and 50 pair
only configurations)
8000 Purfoy Road
Fuquay Varina, NC 27526-9349
Tel 919-557 8900
Fax 919-557 8498
www.tycoelectronics.com
www.telecomosp.com
GelGuard and DTerminator 2 are trademark of Tyco Electronics Corporation.
The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed
to be reliable. However, Tyco Electronics makes no warranties as to its accuracy or completeness and disclaims any liability in connection
with its use. Tyco Electronics’ obligations shall only be as set forth in Tyco Electronics’ Standard Terms and Conditions of Sale for this
product and in no case will Tyco Electronics be liable for any incidental, indirect or consequential damages arising out of the sale, resale,
use or misuse of the product. Users of Tyco Electronics products should make their own evaluation to determine the suitability of each
such product for the specific application.
© 2005 Tyco Electronics Corporation
1307838
C248.0906
EE_FPGA Learning Park
京公网安备 11010802033920号
EEWORLD
