*Static-sensitive device. Unused devices must be stored in conductive material. Protect devices from static discharge and static fields. Stresses above those
listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device
at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to Absolute Maximum Rating
Conditions for extended periods may affect device reliability.
MARKING
3-Pin SOT-23A
3-Pin SOT-89
x ➁ ➂ ➃
➁
x
➃
➂
represents first voltage digit
2 3 4 5 6
3
ex: 3.xv =
kkkk
represents first decimal place voltage (x.0 - x.9)
Qorvo FAE Manager Xun Ying delivered a speech titled "GaN, the Key Technology for Realizing 5G".
Xun Ying pointed out that from the perspective of 5G evolution, not only has the investment in technolo...
GD32L233C-START Development Board Evaluation 1 :
Unboxing, development board interface function analysis and project creation in KEIL development environmentFigure 1: Unboxing of the development board...
When it comes to ARM simulation, we must first know JTAG. JTAG (Joint Test Action Group) is an international standard test protocol (IEEE 1149.1 compatible), mainly used for internal chip testing. Mos...
Time always passes faster than we think or feel. When learning and exploring new technologies, we always overestimate our abilities and underestimate the passage of time! The four-week plan was basica...
STM32F103 and MM32F103 Many programmers and i new students have been asking me this question, STM32F103 and MM32F103, which one is more suitable? Our company has been developing and testing for a peri...
aoyuchipST Sensors & Low Power Wireless Technology Forum
[i=s]This post was last edited by btty038 on 2021-6-8 22:04[/i]Wireless communications don’t provide ubiquitous coverage. We’ve all been there: calls get disconnected, web pages sometimes take a long ...
Failures caused by improper installation of the control valve include increased noise, dirt easily accumulates inside the valve body, causing the control valve to not close tightly, increased leakage...[Details]
To optimize drilling processes and reduce operating costs, Baker Hughes’ Dynamics & Telemetry group developed a sequence prediction algorithm for fast and reliable decoding of downhole data during dri...[Details]
When we electricians need to measure current without disconnecting the circuit, we need to use a clamp meter (sometimes referred to as a clamp meter or clamp meter). A clamp meter is an instrument ...[Details]
The development and application of silicon photonics technology, which realizes light transmission on silicon wafers, has been progressing faster than expected. Among them, Japan has made particularl...[Details]
Now many companies and units are developing PCIe 3.0 motherboards. The consistency test of PCIe 3.0 Tx signal quality and Rx receiving performance is an essential step in the development of PCIe 3.0 ...[Details]
A signal generator is a device that can provide electrical signals of various frequencies, waveforms, and output levels. It is used as a test signal source or excitation source when measuring the amp...[Details]
In industrial detection and data acquisition systems composed of single-chip embedded systems and microcomputers, data communication is often required between computers and single-chip microcomputers...[Details]
The world's first Motorola Edge S equipped with Qualcomm Snapdragon 870 chip is scheduled to be released on January 26. The real photos of the phone have now leaked. The rear camera is arranged...[Details]
The TIM1 timer of ST's STM8 microcontroller is a 16-bit advanced control timer that can be used to achieve basic timing and PWM wave generation. Here we mainly analyze the basic timing function. Le...[Details]
The LM1812 is a complete ultrasonic transceiver designed on a chip. It is used in various pulse echo ranging applications. The chip works by transmitting an oscillating pulse with the help of a conve...[Details]
AT89C5131 is a MCU based on 52 core. In terms of memory, it integrates 32KB Flash memory for code storage and 1KB EEPROM memory for user data storage. Users can use the on-chip Bootloader or Flash A...[Details]
introduction
Laser Doppler displacement measurement technology has the characteristics of high precision, high signal-to-noise ratio, fast dynamic response, good linearity, strong anti-int...[Details]
01 Overview From the perspective of automotive electronics and electrical architecture, a car is a structure composed of ECUs (points) and buses (lines) (wireless sensing is r...[Details]
Wearable applications, convenience and safety risks coexist
"Wearable devices" commonly referred to refer to mobile electronic products that users wear continuously on their bodies rather than...[Details]
In the first half of the year, affected by the sluggish automobile demand in the European and American markets, the revenue and profits of leading automotive manufacturers such as Infineon and NX...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
