FLR300-D4A0.4SA3 datasheet, PDF

FLR300-D4A0.4SA3: DescriptionOn-Delay Relay, DPDT, Momentary, 32VDC (Coil), 2A (Contact), 28VDC (Contact), 0.4s, AC/DC Output, Socket Mount,; CategoryMechanical and electronic products relay; File Size492KB，8 Pages; ManufacturerEsterline Power Systems

Download Datasheet Parametric View All

FLR300-D4A0.4SA3 Overview

On-Delay Relay, DPDT, Momentary, 32VDC (Coil), 2A (Contact), 28VDC (Contact), 0.4s, AC/DC Output, Socket Mount,

Parameter Name	Attribute value
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	PANEL MOUNTABLE
body width	13.3 mm
body height	28.6 mm
Body length or diameter	26 mm
Maximum coil voltage (DC)	32 V
Contact (AC) maximum rated R load	.3A@115VAC
Maximum contact current (AC)	0.3 A
Maximum contact current (DC)	2 A
Contact (DC) maximum rated R load	2A@28VDC
Maximum contact voltage (AC)	115 V
Maximum contact voltage (DC)	28 V
Contact/Output Power Type	AC/DC
Electrical life	100000 Cycle(s)
timed delay	0.4 s
JESD-609 code	e4
Installation features	SOCKET MOUNT
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
physical size	26mm x 13.3mm x 28.6mm
Relay action	MOMENTARY
Relay function	DPDT
Relay type	ON-DELAY RELAY
seal	HERMETICALLY SEALED
surface mount	NO
Terminal surface	GOLD
Termination type	SNAP-ON
Base Number Matches	1

Orthogonal DDS signal single sideband up-conversion modulation: Based on the principle of orthogonal up-conversion modulation, a new method of frequency signal generation is proposed to address some shortcomings of DDS (direct digital frequency synthesis) excitati...; JasonYoo FPGA/CPLD

(A-Current signal detection device) Chongqing "TI Cup" Award_Chongqing University of Posts and Telecommunications: This work designs and implements a non-contact sensing current signal detection device. The peak-to-peak value of the current passing through the load resistor is increased to above 1A through the pow...; sigma Electronics Design Contest

This appears and I can't choose it. It's grayed out.: Help me, this happens when I place a pad. I searched and it said to not select a slot and select a round one, but it is grayed out and I can't select it. What should I do? Thank you!...; chenbingjy PCB Design

【AT-START-F403A Review】3. Try USB Composite_Device: [i=s]This post was last edited by mig29 on 2020-11-6 20:47[/i]This article is mainly used as a memo note: confirm that the USB Composite_Device Demo of Artery is easy to use and has a good program str...; mig29 Domestic Chip Exchange

Communication system cannot do without filter series 2: ...; btty038 RF/Wirelessly

The difference between RETI and RET in MCU assembly instructions: [size=5]Normally, RET is used for return in ordinary assembly subroutines, and RETI is used for interrupt return in interrupt service subroutines. Both instructions can pop the breakpoint address from...; fish001 Microcontroller MCU

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components