EEWORLDEEWORLDEEWORLD

Part Number

Search

M665-02-AA-AM

Description
SAW Oscillator, 622.08MHz Nom, ROHS COMPLIANT PACKAGE-6
CategoryPassive components    oscillator   
File Size302KB,6 Pages
ManufacturerIDT (Integrated Device Technology)
Environmental Compliance
Download Datasheet Parametric View All

M665-02-AA-AM Overview

SAW Oscillator, 622.08MHz Nom, ROHS COMPLIANT PACKAGE-6

M665-02-AA-AM Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerIDT (Integrated Device Technology)
Reach Compliance Codecompliant
Is SamacsysN
Other featuresNOMINAL FREQUENCY 657.4219 MHZ AVAILABLE
Maximum control voltage3.3 V
Minimum control voltage
maximum descent time0.425 ns
Frequency offset/pull rate120 ppm
frequency stability100%
JESD-609 codee3
linearity6%
Installation featuresSURFACE MOUNT
Nominal operating frequency622.08 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeSAW OSCILLATOR
Output compatibilityLVPECL
physical size13.97mm x 8.89mm x 3.05mm
longest rise time0.425 ns
Maximum slew rate125 mA
Maximum supply voltage3.63 V
Minimum supply voltage2.97 V
Nominal supply voltage3.3 V
surface mountYES
maximum symmetry55/45 %
Terminal surfaceMatte Tin (Sn)
Base Number Matches1
M665
D
UAL
SAW, S
ELECTABLE
F
REQUENCY
VCSO
G
ENERAL
D
ESCRIPTION
The M665 is a dual SAW, selectable frequency VCSO
frequency source for low-jitter clock
generation. An integrated SAW (surface
acoustic wave) delay line implements the
high-Q VCO (voltage controlled oscillator)
function, which results in low output phase
noise and very low jitter. The M665-01 is available in
a range of center frequencies from 125 to 177 MHz.
The M665-02 provides 500 to 708 MHz. Guaranteed
minimum pull-range of
±120
ppm meets GbE
requirements. (It also fully satisfies
±50
ppm minimum
pull-range specification commonly required.) Industry-
standard Kvco (VCO Gain) provides full replacement
compatibility. The M665 is well suited for phase-locked
loop implementations, clock and data recovery circuits,
and other timing applications in telecom and optical
fiber networking systems (e.g., OC-48).
P
IN
A
SSIGNMENT
(9 x 14mm SMT)
nFOUT
5
FOUT
4
3
GND
VCC
6
1
VIN
M665
(Top View)
2
Figure 1: Pin Assignment
Sample of Available Output Frequencies
VCSO Center
Frequencies
1
(MHz)
155.5200, 167.3316
156.2500, 161.1328
622.0800, 669.3266
625.0000, 644.5313
Applications
SONET/SDH, SONET/SDH FEC
Gigabit Ethernet, GbE FEC
SONET/SDH, SONET/SDH FEC
Gigabit Ethernet, GbE FEC
F
EATURES
Two integrated SAW devices and selectable output
frequency; supports multi-rate optical interfaces
M665-01 output frequencies from 125 to 177 MHz
M665-02 output frequencies from 500 to 708 MHz
(Specify center frequencies at time of order)
Industry-standard Kvco for full compatibility
Low phase jitter 0.2ps rms typical for the M665-02
(50kHz to 80MHz)
Differential 3.3V LVPECL output
Single 3.3V power supply
Small 9 x 14mm SMT (surface mount) package
Compliant to EC RoHS Directive:
SMT (6 of 6); J-Lead (5 of 6)
Table 1: Sample of Available Output Frequencies
Note 1: Specify VCSO center frequencies at time of order
B
LOCK
D
IAGRAM
M665
SAW Delay Line
VCSO
Phase
Shifter
F_SEL
VIN
SAW Delay Line
FOUT
nFOUT
VCSO
Phase
Shifter
F_SEL
Figure 2: Block Diagram
M665 Datasheet Rev 0.8
M665 Dual SAW, Selectable Frequency VCSO
Revised 30Nov2007
I n t e g t r a t e d D e v i c e Te c h n o l o g y, I n c .
C o m m u n u c a t i o n s M o d u l e s
w w w. i d t . c o m
t e l ( 5 0 8 ) 8 5 2 - 5 4 0 0
MM32F103 Development Board Initial Impressions
The following represents personal opinions, which may not be completely objective. What I received is the F103 development board. The board is not big and is a black development board. I don't like bl...
serialworld Motor Drive Control(Motor Control)
With the configuration parameter table, can AT commands be customized?
Can I customize AT commands to the form of AT_PanID, AT_TarNetAddr, AT_LocNetAddr?...
linee RF/Wirelessly
Sincerely recruiting embedded software and hardware engineers
Familiar with 51 MCU and proteus simulation 2. Familiar with STM32 and FPGA and have independent development experience 3. Be patient Q2391138566...
x03419 Recruitment
Characteristics, functions and precautions of chopper
1. Main features of choppers  The main features of choppers are as follows:  (1) There is a single brake chopper available for each power range, and no parallel connection is required;  (2) It can be ...
ohahaha Power technology
Copper plating under the DC conversion power inductor
[i=s]This post was last edited by qwqwqw2088 on 2022-7-18 09:08[/i]There are often different opinions on whether copper should be placed at the bottom of the inductor of a DC/DC power supply. One view...
qwqwqw2088 Power technology
Regarding FPGA development, compared with several major companies' EDA design tools, Xilinx's Vivado is still the best
[font=楷体, 楷体_GB2312][size=4]In terms of FPGA/CPLD design tools, the overall feeling is that Xilinx's Vivado2018.3 is easier to use. Why? Because the installation package of this tool is about 20G, it ...
深圳De茶叶蛋儿 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号