Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
The latest news shows that the Ukrainian army picked up a crashed Iranian "Shahed-136" suicide drone in Nikolayev Oblast. Since it fell on the river beach, the drone was relatively intact. The outside...
Is there any communication method, any manufacturer or any model of product that can be used as a router in the wireless network, and the outer device can also be used as an end device, and the router...
From TopSemic Embedded, author Norman
Last month, a programmer with 10 years of coding experience got drunk and complained on the social networking site Reddit. Then it was forwarded and liked crazily...
There is a family in the community where Guanguan works who is looking for their child again. Last week, the family looked for their child late at night, dispatched the community security guards, chec...
The CMD file in DSP is a linker command file with the suffix .cmd.Before analyzing the cmd file, you must first understand(1) the memory map of the specific DSP chip (Memory Map)(2) know the knowledge...
OFweek Cup · OFweek 2023 China
Robot
Industry Annual Selection (abbreviated as OFweek Robot Awards 2023) is jointly organized by OFweek, China's high-tech industry portal, and its authorita...[Details]
The method to use a multimeter to check whether the capacitor is damaged is as follows. When checking, first turn the multimeter selection knob to the ohm range R×1kΩ or R×l0kΩ, and then touch ...[Details]
In the early morning of September 25, Apple released the official version update of iOS 13.1. All devices upgraded to iOS 13 can be upgraded to iOS 13.1 system. Under the iOS 13.1 system, the iPho...[Details]
During the 2024 National People's Congress, Zeng Yuqun, member of the National Committee of the Chinese People's Political Consultative Conference and chairman of CATL, submitted four proposals, focus...[Details]
NVIDIA founder and CEO Jensen Huang and NVIDIA leaders spoke at the CogX conference about startups, AI's role in fighting climate change and how AI is advancing key industries like healthcare. ...[Details]
Steps to use Minitools to burn the uboot.bin file into the mini2440 development board: 1. Connect the development board to the computer with a USB cable, turn the S2 switch of the development board...[Details]
The oscilloscope is one of the indispensable equipment in the field of electronic measurement. It is increasingly used and has become a powerful tool in daily work and production. So how to maintain ...[Details]
On April 9, the "12MW/24MWh Energy Storage Power Station Inauguration Ceremony and Lishen Battery User-side Energy Storage Promotion Conference" co-organized by Tianjin Lishen Battery Co., Ltd. (he...[Details]
1 Introduction
At present, in the Tokamak device for magnetic confinement nuclear fusion research at home and abroad, a variety of high-power secondary heating methods are neede...[Details]
At the beginning of 2020, competition in the automotive chip industry has become fierce. Following CES, the opening show of the technology circle, major chip manufacturers showed off their muscles ...[Details]
Summary A standalone PD controller can help address design challenges such as solution size and cost by managing power issues without the need to develop firmware. This article will briefly descri...[Details]
/***********74HC165 parallel input and serial output example program************/ // MCU ATmega8 reads the address of the dip switch of 165 serial input // // Crystal oscillator: internal 1M // ...[Details]
0 Introduction
With the systematization, intelligence, automation and networking of power system operation and management, remote real-time monitoring and automatic debugging of power grid...[Details]
Because all embedded systems use interrupts, how does my S3C44B0 interrupt process? Then I need to understand the whole process. To understand it in depth, the best way is to write a program and th...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
