Data Sheet
Temflex
™
1100, 1100P
Vinyl Corrosion Protection Tape
Product Description
Temflex™ 1100 and 1100P (Printed)
tapes are made of tough, polyvinyl
chloride (PVC), expecially formulated
for corrosion protection of pipes,
conduits and metallic cable jackets.
They are easy to apply and provide
excellent protection against abrasion,
puncture, corrosion and electrolytic
action both above and below ground.
These tapes resist corrosion caused by
acids (e.g. sulfuric, hydrochloric,
phosphoric), alkalies and other
corrosive materials, including
compounds of chlorine, bromine,
sodium and lithium. They also resist
salt water and sunlight.
Features include:
Resistance to galvanic and electrolytic
action
Excellent abrasion resistance
Good impact and tear resistance
Resistance to weather–induced
cracking and checking
High electrical strength
Excellent insulation resistance
Typical Data/Physical
Properties
Dielectric Strength*
10,000 Volts
Engineering/Architectural
All pipe, as indicated on drawings and
listings, shall be protected by
wrapping with a 0.010” (0,254 mm)
vinyl plastic–backed, conformable,
pressure–sensitive tape having
acceptable physical and electrical
properties per ASTM Test Methods.
Temflex™ Corrision Protection Tape,
with application according to
manufacturer’s recommended
procedures, is to be used.
Insulation Resistance*
>10
6
Megohms
Thickness*
Elongation*
Breaking Strength*
Adhesion*
To Steel
To backing
Conf. Factor at 0°C
Fed. Std. L–T–1512A
50 lbs/in
Water Vapor Trans. Rate
ASTM D–3833
(Method 70.1)
g/100 in.
2
(645cm
2
)/24 hrs
*ASTM D–1000
Note: These are typical properties
and should not be used for
specification purposes.
10 mils
200%
25 lbs/in
20 oz/in
20 oz/in
Installation Techniques
Clean and dry surface to be wrapped.
Remove all oil and grease using a rag
and suitable solvent. Remove weld
beads and cover with one layer of
Temflex™ Corrosion Protection Tape
before spiral wrapping. Clean old or
superficially rusted pipe with wire
brush or sand blast before priming
with Scotchrap™ Pipe Primer. Void
areas and sharp edges are to be
padded with Scotchrap™ Pipe
Insulation Putty and covered with one
layer of Temflex™ Corrosion
Protection Tape before spiral
wrapping. Temflex™ Tape should be
spirally wrapped the length of the pipe
using one–half lap for double
thickness. If pipe is to be buried,
application of a coating of
Scotchrap™ Pipe Primer is
recommended before tape is applied.
Under severe backfilling conditions,
rock shield or roofing felt may be
used as additional protection.
passed
1.3
Specifications
Product
The plastic tape is based on polyvinyl
chloride (PVC) and/or its copolymers
and has a specially formulated
rubber–based, pressure–sensitive
adhesive. The tape must be applicable
at temperatures ranging from 10°F to
120°F (–12°C to 49°C) without loss of
physical or electrical properties. The
tape shall be classified for, and have
the capabilities to be used in, both
indoor and outdoor environments.
The tape shall be compatible with all
standard mill coated pipe and must
not crack, split, slip or flag when
exposed to various environments.
Applications
Corrosion protection above and below
ground
Corrosion protection of conduit, pipe
and systems subjected to abrasion,
corrosion, electrolytic action
Corrosion protection of fittings and
joints on mill coated pipe
Moisture sealing of threaded conduit
joint.
Availability
Temflex™ Corrosion Protection Tape
is available from your local 3M
authorized distributor.
Important Notice
All statements, technical information and
recommendations related to the Seller’s
products are based on information
believed to be reliable, but the accuracy or
completeness thereof is not guaranteed.
Before utilizing the product, the user
should determine the suitability of the
product for its intended use. The user
assumes all risks and liability whatsoever
in connection with such use.
Any statements or recommendations of
the Seller which are not contained in the
Seller’s current publications shall have no
force or effect unless contained in an
agreement signed by an authorized officer
of the Seller. The statements contained
herein are made in lieu of all warranties,
express or implied, including but not
limited to the implied warranties of
merchantability and fitness for a particular
purpose which warranties are hereby
expressly disclaimed.
SELLER SHALL NOT BE LIABLE TO THE
USER OR ANY OTHER PERSON
UNDER ANY LEGAL THEORY,
INCLUDING BUT NOT LIMITED TO
NEGLIGENCE OR STRICT LIABILITY,
FOR ANY INJURY OR FOR ANY DIRECT
OR CONSEQUENTIAL DAMAGES
SUSTAINED OR INCURRED BY
REASON OF THE USE OF ANY OF THE
SELLER’S PRODUCTS THAT WERE
DEFECTIVE.
80–6104–3963–2
(c)1991 3M
Litho in U.S.A
3M Electrial Products Division
6801 River Place Blvd.
Austin, TX 78726–4599
MCU
京公网安备 11010802033920号
EEWORLD
