EEWORLDEEWORLDEEWORLD

Part Number

Search

WF106U

Description
DC/DC Converters
File Size51KB,2 Pages
ManufacturerETC
Download Datasheet View All

WF106U Overview

DC/DC Converters

2:1 Input Range
Efficiency to 85%
300kHz Switching Freq
Overvoltage Protec
Remote Disable
Six-sided Shield
External Output Tr
Specification
All specifications are typical at 25°C, nominal line & 75% load
Input
Input Voltage Range
Input Filter
See Table
π
Type
Output
Voltage Accuracy
Single output, ±2% max.
Dual + output, ±2% max.
Dual - output, ±3% max.
Triple 5V, ±2% max.
12V/15V, ±5% max.
Voltage Balance
Dual Output at full load
±1% max.
Transient Response
Single, 25% Step Load Change
<500µ sec
Dual, FL=1/2L±1% Error Band
<500µ sec
External Trim
Adj. Range
±10%
Ripple & Noise
10mV RMS, max
(20MHz BW)
75m V p-p max.
Temperature
±0.02%/°C max.
Coefficient
Short Circuit
Indefinite
Protection
Line Regulation
Single/Dual Output
Triple Output
Load Regulation
Single/Dual Output
Triple Output
±0.5% max.
±1.0% max.
±1.0% max.
±5.0% max.
General
Efficiency
Isolation Voltage
Isolation Resistance
Switching
Frequency
Case Grounding
Operating Temperature
Range
Storage Temperature
Range
See Table
500 VDC min
10
9
ohms min.
300 kHz
Capacity Coupled t
-25°C to +100°C
-55°C to +105°C
Environmental
EMI/RFI
Case Temperature
Case Material
Dimensions
Safety Approvals
Six-sided Continuo
100°C max
Black Coated Copp
Non-Conductive Ba
2 x 2 x 0.40 inches
(50.8 x 50.8 x 10.2 m
UL1950 for U versio
39
www.XP-iQ.com
PH
FAX
Email: sa
Holliston, M
Does anyone know linear system theory? Urgent! ! ! ! ! Thanks! ! ! !
Please solve!!!!...
lgwgt maychang Fun Electronics
I have a question, STM32 drives a three-phase DC brushless controller to drive a DC brushless motor with Hall
The interface of the three-phase DC brushless controller is shown in the figure.The control port (left side) has a hole spacing of 2.0:5V - the control board outputs 5V internally, which can provide a...
zy820 Motor Drive Control(Motor Control)
RISC-V MCU IDE MRS (MounRiver Studio) development: Print FLASH and RAM usage information after compilation
In embedded development, we sometimes need to check the usage of the target chip FLASH and RAM area after compilation. Most IDEs disable this function by default. In this case, we can manually enable ...
Moiiiiilter MCU
EEWORLD University - Solar System Design Made Simple
Solar System Design Made Easy : https://training.eeworld.com.cn/course/4948...
wanglan123 Power technology
Resistance matching problem when transistor is used as switch!
Recently, I used a circuit like the one below, which uses a 5551 to control MJD127, and then controls the on and off of 36V.What I don't understand now is how to select the resistance value of R2 to m...
Kkk- Analog electronics
EEWORLD University ---- Medical monitoring and wearable devices
Medical Monitoring and Wearable Devices : https://training.eeworld.com.cn/course/5547...
hi5 Medical Electronics

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号