PowerPC is a trademark of IBM, Inc. All other trademarks are the property of their respective owners. All specifications are subject to change without notice.
DS078 (v1.10) June 25, 2007
Product Specification
www.xilinx.com
1
R
Spartan-II/Spartan-IIE Family OTP Configuration PROMs (XC17S00A)
Pin Description
Pins not listed are no connects.
8-pin
PDIP
(PD8/PDG8)
and
VOIC/TSOP
(VO8/VOG8)
1
Pin Name
20-pin
SOIC
(SO20)
1
44-pin
VQFP
(VQ44)
40
Pin Description
DATA
•
Data output, High-Z state when either CE or OE are inactive. During
programming, the DATA pin is I/O. Note that OE can be programmed to
be either active High or active Low.
•
Each rising edge on the CLK input increments the internal address
counter, if both CE and OE are active.
•
When High, this input holds the address counter reset and puts the
DATA output in a high-impedance state. The polarity of this input pin is
programmable as either RESET/OE or OE/RESET. To avoid confusion,
this document describes the pin as RESET/OE, although the opposite
polarity is possible on all devices. When RESET is active, the address
counter is held at zero, and the DATA output is in a high-impedance
state. The polarity of this input is programmable. The default is active-
High RESET, but the preferred option is active Low RESET, because it
can be connected to the FPGAs INIT pin and a pull-up resistor.
•
The polarity of this pin is controlled in the programmer interface. This
input pin is easily inverted using the Xilinx HW-130 programmer software.
Third-party programmers have different methods to invert this pin.
•
When High, this pin resets the internal address counter, puts the DATA
output in a high-impedance state, and forces the device into low-I
CC
standby mode.
•
GND is the ground connection.
•
The V
CC
pins are to be connected to the positive voltage supply.
CLK
RESET/OE
(OE/RESET)
2
3
3
8
43
13
CE
4
10
15
GND
V
CC
5
7, 8
11
18, 20
18, 41
38, 35
Pinout Diagrams
DATA (D0)
CLK
OE/RESET
CE
1
2
3
4
8
PD8/PDG8
7
VO8/VOG8
VCC
VCC
NC
GND
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
CLK
NC
GND
DATA(D0)
NC
VCC
NC
Top View
5
ds078_04_061805
ds078_05_061805
NC
OE/RESET
NC
CE
NC
NC
GND
NC
NC
NC
NC
DATA(D0)
NC
CLK
NC
NC
NC
NC
OE/RESET
NC
CE
1
2
3
4
SO20
5
Top View
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
VCC
NC
VCC
NC
NC
NC
NC
NC
NC
GND
1
2
3
4
5
6
7
8
9
10
11
44
43
42
41
40
39
38
37
36
35
34
6
VCC
NC
NC
VQ44
Top View
33
32
31
30
29
28
27
26
25
24
23
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
12
13
14
15
16
17
18
19
20
21
22
ds073_06_061805
DS078 (v1.10) June 25, 2007
Product Specification
www.xilinx.com
2
R
Spartan-II/Spartan-IIE Family OTP Configuration PROMs (XC17S00A)
configuration program from an external memory. The
XC17S00A PROM has been designed for compatibility with
the Master Serial mode.
Upon power-up or reconfiguration, the Spartan device
enters the Master Serial mode when the mode pins are set
to Master Serial mode. Data is read from the PROM
sequentially on a single data line. Synchronization is
provided by the rising edge of the temporary signal CCLK,
which is generated during configuration.
Master Serial mode provides a simple configuration
interface (Figure
1).
Only a serial data line, two control lines,
and a clock line are required to configure the Spartan
device. Data from the PROM is read sequentially, accessed
via the internal address and bit counters which are
incremented on every valid rising edge of CCLK.
If the user-programmable, dual-function D
IN
pin on the
Spartan device is used only for configuration, it must still be
held at a defined level during normal operation. The
Spartan-II/Spartan-IIE family takes care of this
automatically with an on-chip pull-up/down resistor or
keeper circuit.
The one-time-programmable XC17S00A PROM in
Figure 1, page 3
supports automatic loading of
configuration programs. An early DONE inhibits the PROM
data output one CCLK cycle before the Spartan FPGA I/Os
become active.
Controlling PROMs
•
•
•
•
Connecting the Spartan device with the PROM:
The DATA output of the PROM drives the D
IN
input of
the lead Spartan device.
The Master Spartan device CCLK output drives the
CLK input of the PROM.
The RESET/OE input of the PROM is connected to the
INIT pin of the Spartan device and a pull-up resistor.
This connection assures that the PROM address
counter is reset before the start of any
(re)configuration, even when a reconfiguration is
initiated by a V
CC
glitch.
The CE input of the PROM is connected to the DONE
pin of the Spartan device and a pull-up resistor. CE can
also be permanently tied Low, but this keeps the DATA
output active and causes an unnecessary supply
current of 10 mA maximum.
•
FPGA Master Serial Mode Summary
The I/O and logic functions of the Configurable Logic Block
(CLB) and their associated interconnections are established
by a configuration program. The program is loaded either
automatically upon power up, or on command, depending
on the state of the Spartan device mode pins. In Master
Serial mode, the Spartan device automatically loads the
Spartan-II/
Spartan-IIE
Master
Serial
M0
M1
M2
D
IN
CCLK
DONE
INIT
3.3V
3.3
KΩ
3.3V
V
CC
3.3
KΩ
DATA
CLK
CE
V
CC
XC17S00A
PROM
OE/RESET
Notes:
1. If the DriveDone configuration option is not
active,
pull
up
DONE with
a 3.3
kΩ resistor.
DS078_01_061107
Figure 1:
XC17S00A PROM Connections to FPGA in Master Serial Mode
DS078 (v1.10) June 25, 2007
Product Specification
www.xilinx.com
3
R
Spartan-II/Spartan-IIE Family OTP Configuration PROMs (XC17S00A)
Standby Mode
The PROM enters a low-power standby mode whenever CE
is asserted High. The output remains in a high-impedance
state regardless of the state of the OE input.
Programming Spartan-II/Spartan-IIE
Family PROMs
The devices can be programmed on programmers supplied
by Xilinx or qualified third-party vendors. The user must
ensure that the appropriate programming algorithm and the
latest version of the programmer software are used. The
wrong choice can permanently damage the device.
VCC
GND
RESET/
OE
or
OE/
RESET
CE
CLK
Address Counter
TC
EPROM
Cell
Matrix
Output
OE
DATA
DS030_02_011300
Figure 2:
Simplified Block Diagram (does not show programming circuit)
Caution!
Always tie the two V
CC
pins together.
Table 1:
Truth Table for XC17S00A Control Inputs
Control Inputs
RESET
(1)
Inactive
Active
Inactive
Active
Notes:
1.
2.
The XC17S00A RESET input has programmable polarity
[i=s]This post was last edited by jinglixixi on 2021-5-14 09:59[/i]If you want to do your work well, you must first sharpen your tools. If you want to develop CC2650, you can't do without building a d...
STM32 MCU application and full case practice
https://download.eeworld.com.cn/detail/sigma/623925Detailed explanation of microcontroller serial port communication and measurement and control applicatio...
I got to know Arteli after seeing an activity about Arteli on EE by chance.Facing the blockade of the United States, it is the time for domestic chips to work hard. Arteli was founded not long ago, bu...
As LED taillights become mainstream, how to design safe and reliable LED driver circuits has become the primary task of major automotive lighting suppliers. Considering the complexity of the taillight...
After the circuit is determined, the components are selected, and the batch production has been going on for a long time. As a result, the boss often changes in order to reduce costs. For example, the...
Table of Contents update record Use Standard Peripheral Driver update record version status description date author V1.0 C Create Document 2018.10.15 John Wan status: C―― Create， A—— Add， M—— Mod...[Details]
The reporter learned from the Liangjiang New District Investment Promotion Group that in the first half of this year, the energy storage industry chain has focused on supplementing, extending and stre...[Details]
On February 21, Luxshare Precision once again issued an announcement stating that the company plans to raise no more than 13.5 billion yuan through a private placement to be used for the construction...[Details]
Cable is a general term for items such as optical cables, electric wires and cables used for photoelectric signal transmission. Cables have many uses and can be seen everywhere in real life. They are...[Details]
On June 17, the 2nd China Nansha International Integrated Circuit Industry Forum (2023 IC NANSHA), hosted by Xinmo Research, opened in Nansha, Guangzhou. "Daily Economic News" reporters learned on th...[Details]
Recently, the board of directors of CCL (copper foil substrate) manufacturer Taiwan Optoelectronics approved the issuance of convertible corporate bonds with a maximum limit of NT$3.5 billion to rai...[Details]
On January 19, Wang Teng, general manager of Xiaomi's Henan branch, hinted in an interaction with netizens that Xiaomi will have an extra-large cup flagship on the way this year. Starting fro...[Details]
Brushless DC motor (BLDC) and permanent magnet synchronous motor (PMSM) are two widely used motor types in the field of modern electric motors. Although they are similar in many aspects, there are ...[Details]
Turn a simple Arduino Uno (and some Python code) into a crude oscilloscope for viewing waveforms and voltage levels. Oscilloscopes are extremely useful, but usually come with a hefty price tag. L...[Details]
Recently, fires and other safety accidents have occurred one after another in some places, exposing outstanding problems such as inadequate investigation and rectification of hidden dangers and failu...[Details]
Description of the program:
Avago's ACPL-782T is a small isolation amplifier for automotive use, suitable for voltage and current detection in motor drive and battery system monitoring. ACPL-7...[Details]
Statistics show that by the end of 2020, about one million 5G base stations have been deployed worldwide, with about 250 million 5G users. As of January 2021, the number of 5G terminals in the world ...[Details]
The measuring current part of the clamp is composed of the current measuring part and the current measuring part of the multimeter. The iron core of the transformer has a movable part and is connecte...[Details]
This article briefly introduces the high-voltage wiring harness and production process of pure electric vehicles, and makes a detailed analysis of the cost structure and material cost structure of ...[Details]
The goal of this paper is to develop an inertial navigation system for a wheeled vehicle, which can control the movement of the wheeled vehicle and transmit the data collected by the vehicle through ...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
