This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of
this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(V
CC
= 5.0V ±5%, T
A
= -40°C to +85°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
Supply Voltage
V
CC
4.75
High-Level
V
IH
2.2
Input Voltage
Low-Level
V
IL
-0.3
Input Voltage
Input-Leakage
-1.0
I
I
0.0V
≤
V
I
≤
V
CC
Current
V
CC
= Max; Freq =
Active Current
I
CC
1MHz
High-Level
V
CC
= Min; V
OH
= 4
I
OH
Output Current
Low-Level
V
CC
= Min; V
OL
= 0.5
12
I
OL
Output Current
TYP
5.00
MAX
5.25
V
CC
+
0.3
0.8
1.0
30
50
-1
UNITS
V
V
V
μA
mA
mA
mA
6, 8
NOTES
5
5
5
AC ELECTRICAL CHARACTERISTICS
(V
CC
= 5.0V ±5%, T
A
= -40°C to +85°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
20% of
Input
t
WI
Tap 5
Pulse Width
t
PLH
+25°C 5V
-2
Input-to-Tap
0°C to +70°C
-3
t
PLH,
Delay Tolerance
t
PHL
(Delays
≤
40ns)
-40°C to +85°C
-4
+25°C 5V
Input-to-Tap
Delay Tolerance
(Delays > 40ns)
Power-Up Time
Input Period
t
PLH,
t
PHL
t
PU
Period
0°C to +70°C
-40°C to +85°C
-5
-8
-13
2(t
WI
)
TYP
MAX
UNITS
ns
Table 1
Table 1
Table 1
Table 1
Table 1
Table 1
+2
+3
+4
+5
+8
+13
200
ns
ns
ns
%
%
%
μs
ns
NOTES
9
1, 3, 4, 7
1, 2, 3, 4,
7
1, 2, 3, 4,
7
1, 3, 4, 7
1, 2, 3, 4,
7
1, 2, 3, 4,
7
9
CAPACITANCE
(T
A
= +25°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
Input Capacitance
C
IN
MIN
TYP
5
MAX
10
UNITS
pF
NOTES
2 of 7
DS1100
NOTES:
1) Initial tolerances are ± with respect to the nominal value at +25°C and 5V for both leading and
trailing edge.
2) Temperature and voltage tolerance is with respect to the nominal delay value over the stated
temperature range, and a supply-voltage range of 4.75V to 5.25V.
3) All tap delays tend to vary unidirectionally with temperature or voltage changes. For example, if
TAP1 slows down, all other taps also slow down; TAP3 can never be faster than TAP2.
4) Intermediate delay values are available on a custom basis. For further information, email the factory
at
custom.oscillators@maxim-ic.com.
5) All voltages are referenced to ground.
6) Measured with outputs open.
7) See
Test Conditions
section at the end of this data sheet.
8) Frequencies higher than 1MHz result in higher I
CC
values.
9) At or near maximum frequency the delay accuracy can vary and will be application sensitive (i.e.,
decoupling, layout).
Figure 1. LOGIC DIAGRAM
Figure 2. TIMING DIAGRAM: SILICON DELAY LINE
3 of 7
DS1100
TERMINOLOGY
Period:
The time elapsed between the leading edge of the first pulse and the leading edge of the
following pulse.
t
WI
(Pulse Width):
The elapsed time on the pulse between the 1.5V point on the leading edge and the
1.5V point on the trailing edge, or the 1.5V point on the trailing edge and the 1.5V point on the leading
edge.
t
RISE
(Input Rise Time):
The elapsed time between the 20% and the 80% point on the leading edge of the
input pulse.
t
FALL
(Input Fall Time):
The elapsed time between the 80% and the 20% point on the trailing edge of the
input pulse.
t
PLH
(Time Delay, Rising):
The elapsed time between the 1.5V point on the leading edge of the input
pulse and the 1.5V point on the leading edge of any tap output pulse.
t
PHL
(Time Delay, Falling):
The elapsed time between the 1.5V point on the trailing edge of the input
pulse and the 1.5V point on the trailing edge of any tap output pulse.
TEST SETUP DESCRIPTION
Figure 3 illustrates the hardware configuration used for measuring the timing parameters on the DS1100.
The input waveform is produced by a precision-pulse generator under software control. Time delays are
measured by a time interval counter (20ps resolution) connected between the input and each tap. Each tap
is selected and connected to the counter by a VHF switch control unit. All measurements are fully
automated, with each instrument controlled by a central computer over an IEEE 488 bus.
TEST CONDITIONS INPUT
Ambient Temperature:
Supply Voltage (V
CC
):
Input Pulse:
Source Impedance:
Rise and Fall Time:
Pulse Width:
Period:
+25°C
±3°C
5.0V
±0.1V
High = 3.0V
±0.1V
Low = 0.0V
±0.1V
50Ω max
3.0ns max (measured between 0.6V and 2.4V)
500ns (1μs for
-500 version)
1μs (2μs for
-500 version)
OUTPUT:
Each output is loaded with the equivalent of one 74F04 input gate. Delay is measured at the 1.5V level on
the rising and falling edge.
Note: Above conditions are for test only and do not restrict the operation of the device under other
Positive and negative power supply of operational amplifier, in-phase amplification and inverting amplification applications1. Do op amps powered by positive and negative power supplies have a larger ...
1. About product EMC pre-test50 % of projects fail the first EMC test . If you are developing a product, you have to invest money, time, and sometimes emotion to get the product to market. And in the ...
Components and Electromagnetic Compatibility : https://training.eeworld.com.cn/course/5425Hardware Trio Components and Electromagnetic Compatibility Video Tutorial...
Smartphones are now indispensable communication tools. There are many types of sensors on smartphones, and each sensor plays a different role. So what is the role of mobile phone pressure sensors? Her...
I designed a 3-8 priority encoder using vhdl language. When writing a testbench and using modelsim for sequential simulation, it started normally, but an indeterminate state X appeared in the middle (...
The high-voltage isolated differential probe is a powerful tool for floating measurement of high-voltage signals. It uses a universal interface and is compatible with all mainstream brands of osc...[Details]
The product development of general single-chip microcomputer application systems adopts a bottom-up process, that is, according to the application requirements, the corresponding slave devices are ...[Details]
0 Introduction
As a new type of power transformer, the power electronic transformer (PET) has attracted more and more attention from researchers at home and abroad. It is a power transform...[Details]
As the smartphone market has long been close to saturation, smartphone manufacturers have been continuously making efforts in the field of optics since 2016, and have been developing in the direction...[Details]
0 Introduction
Ethernet has the characteristics of strong versatility, mature technology, and rapidly increasing bandwidth. With the emergence of embedded technology in the field of industrial contr...[Details]
1 Introduction
AutoCAD2005 is a series of products of Autodesk. The software follows the drawing habits of engineering draftsmen in terms of usage and design ideas. It can easily draw engi...[Details]
We will walk through the steps for testing switching and conduction losses in a power supply.
Remember that switching losses and conduction losses through the power switches and magnetic...[Details]
1 Introduction
Before launching a certain aircraft, it is necessary to test various parameters of the aircraft. The parameter test is to record the aircraft data through a data recorder an...[Details]
According to Jiwei.com, on October 8, the National Procurement Center located in Wuhan Optics Valley Central City announced that OPPO Wuhan R&D Center has officially begun operations. OPPO Wuhan R&...[Details]
Since the beginning of this year, there has been a continuous stream of good news about solid-state batteries. On the one hand, manufacturers have continuously obtained various financings, and on the...[Details]
Get the most out of your iPhone. Your iPhone is full of hidden features, and iOS 15 has some, too In every release — including iOS 15.4, which is expected to roll out next week — Apple hides useful...[Details]
In the development of single-chip microcomputers, the serial port is the most commonly used channel for exchanging data with the outside world. To use the serial port, a communication protocol is e...[Details]
According to foreign media reports, researchers at the U.S. Department of Energy's Argonne National Laboratory have developed a new electrolyte mixture and a simple additive that can increase the sur...[Details]
Abstract: Aiming at the problems of abstract concepts and difficulty in understanding in the teaching of "Signal and System" course, a soft platform for experimental teaching based on LabVIEW softwar...[Details]
Recently, Tianma's 8.6th generation new display panel production line project with a total investment of 33 billion yuan entered the implementation stage. The content of this investment and construc...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
