f = 80.000001 MHz, all Vdds. For other freq, T_oe = 100 ns + 3
clock periods
See Figure 8 for resume timing diagram
f = 156.25 MHz, Vdd = 2.5V, 2.8V or 3.3V
f = 156.25 MHz, Vdd = 1.8V
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz
LVCMOS Output Characteristics
Output Low Voltage
VOL
–
–
10%
Vdd
Input Characteristics
Input Pull-up Impedance
Input Capacitance
Startup Time
OE Enable/Disable Time
Resume Time
RMS Period Jitter
RMS Phase Jitter (random)
Z_in
C_in
T_start
T_oe
T_resume
T_jitt
T_phj
–
–
–
–
–
–
–
–
100
5
–
–
7
1.5
2
0.5
250
–
10
115
10
Jitter
2
3
1
ps
ps
ps
kΩ
pF
ms
ns
ms
Startup and Resume Timing
Notes:
1. All electrical specifications in the above table are specified with 15 pF output load and for all Vdd(s) unless otherwise stated.
2. The typical value of any parameter in the Electrical Characteristics table is specified for the nominal value of the highest voltage option for that parameter and at
25°C temperature.
3. All max and min specifications are guaranteed across rated voltage variations and operating temperature ranges, unless specified otherwise
4. Initial tolerance is measured at Vin = Vdd/2
5. Absolute Pull Range (APR) is defined as the guaranteed pull range over temperature and voltage.
6. APR = pull range (PR) - frequency stability (F_stab) - Aging (F_aging)
Rev. 1.01
Page 2 of 9
www.sitime.com
SiT3809
80 MHz to 220 MHz MEMS VCXO
The Smart Timing Choice
The Smart Timing Choice
Table 2. Pin Description. 4-Pin Configuration
(For 2.5 x 2.0 mm and 3.2 x 2.5 mm packages)
Pin
1
2
3
4
Symbol
VIN
GND
CLK
VDD
Input
Power
Power
Input
Power
Electrical ground
Power supply voltage
Oscillator output power
[7]
GND
2
3
Top View
Functionality
VIN
1
4
0-Vdd: produces voltage dependent frequency change
VDD
CLK
Note:
7. A capacitor value of 0.1 µF between VDD and GND is recommended.
Figure 1.
Table 3. Pin Description. 6-Pin Configuration
(For 5.0 x 3.2 mm and 7.0 x 5.0 mm packages)
Pin
1
Symbol
VIN
Input
No
Connect
2
NC/OE/ ST
Output
Enable
Standby
3
4
5
6
GND
CLK
NC
VDD
Power
Output
No
Connect
Power
Functionality
0-Vdd: produces voltage dependent frequency change
H or L or Open: No effect on output frequency or other device
functions
H or Open
[8]
: specified frequency output
L: output is high
H or Open
[8]
: specified frequency output
L: output is low (weak pull down)
[9]
. Oscillation stops
Electrical ground
Oscillator output
H or L or Open: No effect on output frequency or other device
functions
Power supply voltage
[10]
VIN
NC/OE/ST
GND
1
6
Top View
VDD
NC
CLK
2
5
3
4
Figure 2.
Notes:
8. In OE or ST mode, a pull-up resistor of 10 kΩ or less is recommended if pin 2 in the 6-pin package is not externally driven. If pin 2 needs to be left floating, use
the NC option
9. Typical value of the weak pull-down impedance is 5 mΩ
10. A capacitor value of 0.1 µF between VDD and GND is recommended.
Table 4. Absolute Maximum Limits
Attempted operation outside the absolute maximum ratings may cause permanent damage to the part. Actual performance of
the IC is only guaranteed within the operational specifications, not at absolute maximum ratings.
Parameter
Storage Temperature
VDD
Electrostatic Discharge
Soldering Temperature (follow standard Pb free soldering guidelines)
Min.
-65
-0.5
–
–
Max.
150
4
2000
260
Unit
°C
V
V
°C
Table 5. Thermal Consideration
Parameter
7050
5032
3225
2520
JA, 4 Layer Board
(°C/W)
191
97
109
117
JA, 2 Layer Board
(°C/W)
263
199
212
222
JC, Bottom
(°C/W)
30
24
27
26
Table 6. Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
Rev. 1.01
Page 3 of 9
www.sitime.com
SiT3809
80 MHz to 220 MHz MEMS VCXO
The Smart Timing Choice
The Smart Timing Choice
Phase Noise Plot
SiT3809, 100MHz, Pull range ±100ppm, 3.3V, LVCMOS output
-80
-90
Phase Noise (dBc/Hz)
-100
-110
-120
-130
-140
-150
-160
3
10
Integrated Random Phase Jitter (RMS, 12kHz - 20MHz): 0.51 ps
10
4
10
5
10
6
10
7
Offset Frequency (Hz)
Figure 3. Phase Noise
Test Circuit and Waveform
Vdd
Vout
Test
Point
6
15pF
(including probe
and fixture
capacitance)
Power
Supply
0.1µF
5
Vout
Test
Point
4
Power
Supply
0.1µF
3
4
15pF
(including probe
and fixture
capacitance)
1
2
1
2
3
OE/ST Function
Vc
OE/ST Function
Vc
Vdd
Figure 4. Test Circuit (4-Pin Device)
Figure 5. Test Circuit (6-Pin Device)
tr
90% Vdd
50%
10% Vdd
High Pulse
(TH)
Period
tf
Low Pulse
(TL)
Figure 6. Waveform
Notes:
11. Duty Cycle is computed as Duty Cycle = TH/Period.
12. SiT3809 supports the configurable duty cycle feature. For custom duty cycle at any given frequency, contact
SiTime.
Rev. 1.01
Page 4 of 9
www.sitime.com
SiT3809
80 MHz to 220 MHz MEMS VCXO
The Smart Timing Choice
The Smart Timing Choice
Timing Diagram
Vdd
50% Vdd
Pin 4 Voltage
T_start
No Glitch
during start up
80% Vdd, 2.5/2.8/3.3V devices
80% Vdd, 1.8V devices
Vdd
ST Voltage
T_resume
CLK Output
CLK Output
T_start: Time to start from power-off
T_resume: Time to resume from ST
Figure 7. Startup Timing (OE/ST Mode)
u
Vdd
50% Vdd
OE Voltage
T_oe
Figure 8. Standby Resume Timing (ST Mode Only)
Vdd
OE Voltage
50% Vdd
T_oe
CLK Output
CLK Output
HZ
T_oe: Time to re-enable the clock output
T_oe: Time to put the output in High Z mode
Figure 9. OE Enable Timing (OE Mode Only)
Figure 10. OE Disable Timing (OE Mode Only)
Notes:
13. SiT3809 supports “no runt” pulses and “no glitch” output during startup or resume.
14. SiT3809 supports gated output which is accurate within rated frequency stability from the first cycle.
[i=s]This post was last edited by alan000345 on 2019-9-29 07:41[/i]The role of small base stations increases with the increase of "G". It is said that with the release of the 5G NSA standard and the "...
Sensitivity?
Sensitivity refers to the sensitivity of the device to the gas being measured. The sensitivity is usually expressed by the ratio of the resistance of the gas sensor in a certain concentra...
[align=left][color=rgb(85, 85, 85)][font="][size=4] Multicore DSP implementations require intelligent power management given the plethora of voltage and current requirements for the core, memory, I/O,...
[i=s]This post was last edited by Tongxin Laosou on 2018-11-19 12:31[/i] I disassembled and repaired the driving circuit of a microscope halogen light source. Although I have drawn a sketch, I don't u...
Activities currently being applied for1. Xingkong Board Python Programming Learning Control Panel ( Newly Launched )
The Xingkong board adopts a microcomputer architecture, integrating LCD color scree...
[i=s]This post was last edited by w494143467 on 2021-6-14 17:01[/i]1. Introduction
When it comes to data communication between devices, I was struggling between Mesh and broadcast, but in the end I ch...
w494143467onsemi and Avnet IoT Innovation Design Competition
FPGAs are well suited for precision motor control, and in this project we will create a simple motor control program upon which more complex applications can be built.
Required Hardware
...[Details]
During the Beijing Auto Show in April, we met Jack Weast, Intel Fellow, Vice President of Intel Corporation, and General Manager of the Automotive Division. He revealed Intel Automotive's China pla...[Details]
Smart home systems use home networks to allow various devices in the system to interact with each other, creating an intelligent, comfortable and convenient living environment for consumers. Compar...[Details]
Bus node CPX-M-FB35
Operating voltage range DC: 18 V ... 30 V
Parameter settings:
Diagnostic features, error-proof response, forced channels, signal settings, system parameters...[Details]
Audi has spent a lot of time building up its electric drive system, which we have introduced before. Today, we will continue to share Audi’s choice of motors.
● The system output of the ...[Details]
1) In the text box that defines the include file path, there are two very important syntaxes for defining the include file path. One is $TOOLKIT_DIR$. This syntax means that the include file path i...[Details]
Author:
Frank Lamb
Troubleshooting and maintenance of motion control and robotics requires a deep understanding of all components and mechanisms in the robot.
Motion control involve...[Details]
The main function of the amplifier in the multimedia broadcasting system is to amplify the weak audio input voltage signal generated by various means and then send it to each user's device. The amp...[Details]
In an intelligent workshop in the Chengdu Economic Development Zone's Jingrong Digital Economy Industrial Park, workers are working in an orderly manner, and the fully automatic production line is run...[Details]
Hyundai Mobis has integrated its display innovations to set new standards for the future digital cockpit. The digital cockpit is an infotainment system installed in front of the driver and passenge...[Details]
On March 5, Chery officially announced that Chery EXEED Xingtu Yaoguang C-DM will be officially launched on March 11. According to the official website information, Xingtu Yaoguang C-DM will launch 4...[Details]
Chassis technology has always been the focus of competition among major car companies. In the past era of gasoline trucks, BBA showed its talents in "magic carpet" technology, from the magic body con...[Details]
Recently, Tektronix announced that its advanced semiconductor open laboratory in Beijing has been fully upgraded and officially launched Version 2.0, which indicates that the company is following t...[Details]
In modern industry, servo motors are used more and more widely. Its advantages such as high speed, high precision and high reliability have been widely used in various industries. However, in pract...[Details]
According to news on September 4, Xin Guobin, a member of the Party Leadership Group and Vice Minister of the Ministry of Industry and Information Technology, said at the 2023 China Automobile Indust...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
