RoHS Compliant
SATA-Disk Module 4
SDM4-M 7P/90D Middle Profile Specifications
July 5
th
, 2013
Version 1.3
Apacer Technology Inc.
4 Fl., 75 Hsin Tai Wu Rd., Sec.1, Xizhi, New Taipei City, Taiwan 221
Tel: +886-2-2698-2888
www.apacer.com
Fax: +886-2-2698-2889
th
SATA-Disk Module 4
APSDMxxxxG5AN-PXXX
Features:
Standard Serial ATA Revision 2.6
–
Compliance with SATA Revision 2.6
specifications
–
SATA 3.0 Gbps
–
ATA-compatible command set
Capacities
–
4, 8, 16, 32, 64 GB
Performance*
–
Burst read/write: 300 MB/sec
–
Sustained read: up to 85 MB/sec
–
Sustained write: up to 43 MB/sec
Intelligent endurance design
–
Built-in hardware ECC, enabling up to
16/24 bit correction per 1K bytes
–
Static/dynamic wear-leveling
–
Flash bad-block management
–
S.M.A.R.T.
–
Power Failure Management
–
ATA Secure Erase
–
TRIM
NAND Flash Type:
SLC
Temperature ranges
–
Operation:
Standard: 0° to 70° (32 ~ 158°
C
C
F)
Extended: -40° to 85°
C
C(-40° ~ 185°
F)**
–
Storage: -40° to 100° (-40° ~ 212°
C
C
F)
Supply voltage
–
5.0 V 5%
Power consumption (typical)*
–
Active mode: 225 mA@5.0 V
–
Idle mode: 83 mA@5.0 V
Connector type
–
7-pin signal connector
–
Power segment in two types: power cable
and power cable-less types
Form factor
–
Middle profile SATA Disk Module
–
Dimension: 58.0 x 24.0 x1.0***, unit: mm
Shock & Vibration****
–
Shock: 1500 G
–
Vibration: 15 G
MTBF: >1,000,000
hours
Write Protect (optional)
–
Enabled by onboard hardware switch
RoHS compliant
*Varies from capacities. The values for performances and power consumptions presented are typical and may vary depending on
flash configurations or platform settings. The term idle refers to the standby state of the device.
**Only available in 8, 16 and 32GB models.
***Implies to only the thickness of the module, without including the height/thickness of the connector head.
****Non-operating
1
© 2013 Apacer Technology Inc.
Rev. 1.3
±
SATA-Disk Module 4
APSDMxxxxG5AN-PXXX
Table of Contents
1. GENERAL DESCRIPTION .................................................................................................... 3
2. FUNCTIONAL BLOCK .......................................................................................................... 3
3. PIN ASSIGNMENTS ............................................................................................................... 4
4. PRODUCT SPECIFICATION ................................................................................................ 6
4.1 C
APACITY
.............................................................................................................................................................6
4.2 P
ERFORMANCE
.....................................................................................................................................................6
4.3 E
NVIRONMENTAL
S
PECIFICATIONS
.......................................................................................................................7
4.4 M
EAN
T
IME
B
ETWEEN
F
AILURES
(MTBF) ...........................................................................................................7
4.5 C
ERTIFICATION AND
C
OMPLIANCE
.......................................................................................................................7
5. FLASH MANAGEMENT ....................................................................................................... 8
5.1 E
RROR
C
ORRECTION
/D
ETECTION
.........................................................................................................................8
5.2 F
LASH
B
LOCK
M
ANAGEMENT
..............................................................................................................................8
5.3 W
EAR
L
EVELING
..................................................................................................................................................8
5.4 P
OWER
F
AILURE
M
ANAGEMENT
...........................................................................................................................8
5.5 ATA S
ECURE
E
RASE
............................................................................................................................................8
5.6 S.M.A.R.T............................................................................................................................................................9
5.7 TRIM ...................................................................................................................................................................9
6. SOFTWARE INTERFACE .................................................................................................. 10
6.1 C
OMMAND
S
ET
...................................................................................................................................................10
7. ELECTRICAL SPECIFICATION ...................................................................................... 11
8. PHYSICAL CHARACTERISTICS ..................................................................................... 12
8.1 P
OWER
C
ABLE
T
YPE
...........................................................................................................................................12
8.2 P
OWER
C
ABLE
-
LESS
T
YPE
..................................................................................................................................13
8.3 W
RITE
P
ROTECT
S
WITCH
(
OPTIONAL
)................................................................................................................14
9. PRODUCT ORDERING INFORMATION ........................................................................ 15
9.1 P
RODUCT
C
ODE
D
ESIGNATIONS
.........................................................................................................................15
2
© 2013 Apacer Technology Inc.
Rev. 1.3
SATA-Disk Module 4
APSDMxxxxG5AN-PXXX
1. General Description
Apacer’s SATA-Disk Module 4 MLC version (SDM4-M) is a high-performance, embedded SSD DOM
(Disk on Module) designed to replace the conventional SATA storage devices. SDM4-M can be fitted into
a standard Serial ATA connectors commonly found in desktops, IT-STB, industrial PC and thin client
systems. In addition, SDM4-M provides an innovative way for design-in clients with compact host
computing systems.
Apacer’s SDM4-M is built in with an efficient microcontroller that drives the potential of NAND flash and
delivers optimal performance. With its compact form factor and SATA 3.0 Gbps interface, this product is
well suited for embedded flash storage applications offering customizable and expanded functionalities as
well as more cost-effective designs, better performance and increased reliability.
2. Functional Block
SDM4-M includes the SATA and Flash Management controllers, and flash media, as well as the SATA
standard interface. Figure 2-1 shows the functional block diagram.
Flash interface & ECC engine
Flash
Flash
Flash
Flash
SATAI Interface
SATA 3.0 Gbps
Interface
Controller
Host
Figure 2-1:
Functional block diagram
3
© 2013 Apacer Technology Inc.
Rev. 1.3
SATA-Disk Module 4
APSDMxxxxG5AN-PXXX
3. Pin Assignments
Power Pin 1 (Vcc)
for the Power
Cable-less Type
Signal Pin 1
Power Pin 1 (Vcc)
for the Power
Cable Type
Table 3-1:
Signal segment
Name
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Type
GND
RxP
RxN
GND
TxN
TxP
GND
+ Differential Receive Signal
- Differential Receive Signal
- Differential Transmit Signal
+ Differential Transmit Signal
Description
Table 3-2:
Power segment
Name
Pin 1
Pin 2
Description
VCC (5V)
GND
4
© 2013 Apacer Technology Inc.
Rev. 1.3
TI Technology Forum
京公网安备 11010802033920号
EEWORLD
