Product data sheet
Characteristics
ATV32HD11N4
variable speed drive ATV32 - 11 kw - 400 V - 3
phase - with heat sink
Main
Range of product
Product or component
type
Product specific appli-
cation
Assembly style
Component name
EMC filter
Network number of
phases
[Us] rated supply volt-
age
Motor power kW
Motor power hp
Line current
Apparent power
Prospective line Isc
Nominal output current
Maximum transient cur-
rent
Speed drive output fre-
quency
Nominal switching fre-
quency
Switching frequency
Asynchronous motor
control profile
Altivar 32
Variable speed drive
Complex machines
With heat sink
ATV32
Class C2 EMC filter integrated
3 phases
380...500 V (- 15...10 %)
11 kW at 380...500 V 3 phases
15 hp at 380...500 V 3 phases
36.6 A for 380 V 3 phases 11 kW / 15 hp
25.6 A for 500 V 3 phases 11 kW / 15 hp
31.7 kVA at 500 V 3 phases 15 kW / 20 hp
<= 22 kA, 3 phases
27.7 A at 4 kHz 500 V 3 phases 11 kW / 15 hp
41.6 A for 60 s 3 phases 11 kW / 15 hp
0.5...599 Hz
4 kHz
2...16 kHz adjustable
Voltage/Frequency ratio, 2 points
Voltage/Frequency ratio, 5 points
Flux vector control without sensor - Energy Saving,
NoLoad law
Flux vector control without sensor, standard
Voltage/Frequency ratio - Energy Saving, quadratic
U/f
No impedance for Modbus
The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein.
This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications.
It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof.
Neither Schneider Electric Industries SAS nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein.
Type of polarization
Complementary
Product destination
Supply voltage limits
Supply frequency
Network frequency limits
Speed range
Speed accuracy
Torque accuracy
Transient overtorque
Braking torque
Synchronous motor control profile
Regulation loop
Motor slip compensation
Asynchronous motors
Synchronous motors
323...550 V
50...60 Hz (- 5...5 %)
47.5...63 Hz
1...100 for asynchronous motor in open-loop mode
+/- 10 % of nominal slip for 0.2 Tn to Tn torque variation
+/- 15 %
170...200 % of nominal motor torque
< 170 % with braking resistor
Vector control without sensor
Adjustable PID regulator
Automatic whatever the load
Not available in voltage/frequency ratio (2 or 5 points)
Adjustable 0...300 %
Jun 6, 2014
1
Local signalling
1 LED red presence of drive fault
1 LED red presence of CANopen error
1 LED green presence of CANopen run
1 LED blue presence of bluetooth
1 LED red presence of drive voltage
<= power supply voltage
Electrical between power and control
Power supply screw terminal 10...16 mm² / AWG8...AWG6
Motor/Braking resistor removable screw terminals 6...16 mm² / AWG8...AWG6
Control screw terminal 0.5...1.5 mm² / AWG18...AWG14
Power supply 1.2 N.m / 10.6 lb/ft
Motor/Braking resistor 1.2 N.m / 10.6 lb/ft
Control 0.5 N.m / 4.4 lb/ft
Internal supply for reference potentiometer (1 to 10 kOhm), 10.5 V DC +/- 5 %,
<= 10 mA for overload and short-circuit protection
3
AI3 current 0...20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by config-
uration), impedance 250 Ohm, resolution 10 bits
AI2 bipolar differential voltage +/- 10 V DC, impedance 30000 Ohm, resolution 10
bits
AI1 voltage 0...10 V DC, impedance 30000 Ohm, resolution 10 bits
AO1 2 ms for analog input(s)
AI1, AI2, AI3 2 ms for analog input(s)
R2A, R2C 2 ms for relay output(s)
R1A, R1B, R1C 2 ms for relay output(s)
LI1...LI6 8 ms, tolerance +/- 0.7 ms for logic output(s)
AO1 +/- 2 % for a temperature of -10...60 °C
AO1 +/- 1 % for a temperature of 25 °C
AI1, AI2, AI3 +/- 0.5 % for a temperature of 25 °C
AI1, AI2, AI3 +/- 0.2 % for a temperature of -10...60 °C
AO1 +/- 0.3 %
AI1, AI2, AI3 +/- 0.2...0.5 % of maximum value
1
AO1 software-configurable voltage 0...10 V, impedance 470 Ohm, resolution 10
bits
AO1 software-configurable current 0...20 mA, impedance 800 Ohm, resolution 10
bits
3
LO logic
R2A, R2B configurable relay logic NO, electrical durability 100000 cycles
R1A, R1B, R1C configurable relay logic NO/NC, electrical durability 100000 cy-
cles
Configurable relay logic 5 mA at 24 V DC
R2 on resistive load, 5 A at 30 V DC, cos phi = 1,
R2 on resistive load, 5 A at 250 V AC, cos phi = 1,
R1, R2 on inductive load, 2 A at 30 V DC, cos phi = 0.4,
R1, R2 on inductive load, 2 A at 250 V AC, cos phi = 0.4,
R1 on resistive load, 4 A at 30 V DC, cos phi = 1,
R1 on resistive load, 3 A at 250 V AC, cos phi = 1,
7
STO safe torque off 24...30 V DC, impedance 1500 Ohm
LI6 switch-configurable PTC probe 24...30 V DC
LI5 programmable as pulse input 20 kpps 24...30 V DC, with level 1 PLC
LI1...LI4 programmable (sink/source) 24...30 V DC, with level 1 PLC
LI1...LI6 positive logic (source), < 5 V (state 0), > 11 V (state 0)
LI1...LI6 negative logic (sink), > 19 V (state 0), < 13 V (state 0)
S
U
CUS
Deceleration ramp automatic stop DC injection
Deceleration ramp adaptation
Linear
Ramp switching
By DC injection
Thermal protection drive
Short-circuit between motor phases drive
Overheating protection drive
Overcurrent between output phases and earth drive
Input phase breaks drive
Output voltage
Insulation
Electrical connection
Tightening torque
Supply
Analogue input number
Analogue input type
Sampling duration
Response time
Accuracy
Linearity error
Analogue output number
Analogue output type
Discrete output number
Discrete output type
Minimum switching current
Maximum switching current
Discrete input number
Discrete input type
Discrete input logic
Acceleration and deceleration ramps
Braking to standstill
Protection type
2
Communication port protocol
Type of connector
Physical interface
Transmission frame
Number of addresses
Method of access
Marking
Operating position
Width
Height
Depth
Product weight
Option card
CANopen
Modbus
1 RJ45 for Modbus/CANopen on front face
2-wire RS 485 for Modbus
RTU for Modbus
1...247 for Modbus
1...127 for CANopen
Slave for CANopen
CE
Vertical +/- 10 degree
180 mm
404 mm
232 mm
8.7 kg
Communication card Profibus DP V1
Communication card Ethernet/IP
Communication card DeviceNet
Communication card CANopen open style
Communication card CANopen daisy chain
Environment
Noise level
Electromagnetic compatibility
43 dB conforming to 86/188/EEC
Voltage dips and interruptions immunity test conforming to IEC 61000-4-11
Radiated radio-frequency electromagnetic field immunity test conforming to IEC
61000-4-3 level 3
Electrostatic discharge immunity test conforming to IEC 61000-4-2 level 3
Electrical fast transient/burst immunity test conforming to IEC 61000-4-4 level 4
Conducted radio-frequency immunity test conforming to IEC 61000-4-6 level 3
1.2/50 µs - 8/20 µs surge immunity test conforming to IEC 61000-4-5 level 3
EN 55011 class A group 1
EN 61800-3 environments 1 category C2
EN 61800-3 environments 2 category C2
EN/IEC 61800-3
EN/IEC 61800-5-1
CSA
C-Tick
GOST
NOM 117
UL
2 conforming to EN/IEC 61800-5-1
IP20 conforming to EN/IEC 61800-5-1
1.5 mm peak to peak (f = 3...13 Hz) conforming to EN/IEC 60068-2-6
1 gn (f = 13...200 Hz) conforming to EN/IEC 60068-2-6
15 gn for 11 ms conforming to EN/IEC 60068-2-27
5...95 % without dripping water conforming to IEC 60068-2-3
5...95 % without condensation conforming to IEC 60068-2-3
50...60 °C with derating factor
-10...50 °C without derating
-25...70 °C
1000...3000 m with current derating 1 % per 100 m
<= 1000 m without derating
Standards
Product certifications
Pollution degree
IP degree of protection
Vibration resistance
Shock resistance
Relative humidity
Ambient air temperature for operation
Ambient air temperature for storage
Operating altitude
Offer Sustainability
Sustainable offer status
RoHS
Not Green Premium product
Compliant - since 1012 -
Schneider Electric declaration of conformity
3
MicroPython Open Source section
京公网安备 11010802033920号
EEWORLD
