P5-418333 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Mechanical and electronic products> switch> P5-418333

P5-418333: DescriptionPushbutton Switch, SPDT, On-on, Alternate, 10A, 28VDC, Solder Terminal, Panel Mount-threaded; CategoryMechanical and electronic products switch; File Size696KB，2 Pages; ManufacturerOTTO; Websitehttp://www.ottoexcellence.com

Download Datasheet Parametric View All

P5-418333 Overview

Pushbutton Switch, SPDT, On-on, Alternate, 10A, 28VDC, Solder Terminal, Panel Mount-threaded

P5-418333 Parametric

Parameter Name	Attribute value
Reach Compliance Code	unknown
ECCN code	EAR99
Actuator angle
Actuator length	0.25 inch
Actuator material	NYLON
Actuator stroke	4.572 mm
Actuator type	PUSHBUTTON
Other features	ORANGE, WATERPRF RED BEZ
body height	22.33 mm
Body length or diameter	14.27 mm
Nozzle length	0.34 inch
Casing type	15/32-32
Center contact plating	GOLD
Contact (AC) maximum rated load I	5A@115VAC
Contact (AC) maximum rated load M	3A@115VAC
Contact (AC) maximum rated R load	10A@115VAC
Maximum contact current (AC)	10 A
Maximum contact current (DC)	10 A
Contact (DC) maximum rated R load	10A@28VDC
Contact function	ON-ON
contact time	SNAP ACTION
Maximum contact voltage (AC)	115 V
Maximum contact voltage (DC)	28 V
Dielectric withstand voltage	1050VRMS V
Electrical life	25000 Cycle(s)
End contact plating	GOLD
Shell material	ALUMINUM ALLOY
JESD-609 code	e4
Manufacturer's serial number	P5
Installation features	PANEL MOUNT-THREADED
Maximum operating force	17.79 N
seal	EPOXY TERMINAL SEALED; IP68
surface mount	NO
Switch action	ALTERNATE
switch function	SPDT
Switch type	PUSHBUTTON SWITCH
Terminal surface	GOLD/SILVER
Terminal length	0.156 inch
Termination type	SOLDER
Base Number Matches	1

Preview

Download Datasheet

View All

ALTERNATE

ACTION

ALTERNATE ACTION PUSHBUTTONS

SEALED AGAINST DUST & MOISTURE

The P5 Alternate Action switches match the P1, P3 and P8

Momentary Action Pushbutton models for mixed function

with common panel appearance. Now you can design panels

with both alternate and momentary action switches and have

uniform panel appearance. The P5 features alternate action

in the same pushbutton and housing configuration as the

momentary P1 and P3 and as a bonus, the P5 requires less

behind the panel space than the P1 and P3 momentary versions.

Push and the P5 switch turns “on.” Push again and the P5 switch

turns “off.” Positive tactile feedback is featured so the operator

is clearly aware the switch mode has been executed. The button

returns to the original position after each actuation.

To guard against front panel splash and dirt, the P5 series

is sealed at the button with OTTO’s patented “rolling

sleeve”principle. The terminals are sealed with epoxy, providing

a seal against flux during wiring and behind panel dirt and

moisture. The combination of sealing provides smooth operation

over a wide temperature range. Watertight sealing to IP68S is

available.

A vandal resistant style is available in the P5-V series. Custom

housings, shrouded buttons, contact configurations and

materials are available to suit your application requirements. We

also provide custom button engraving with epoxy ink backfill,

watertight versions and other special characteristics.

, Push O

“Push On

ff” action

Style P5-4

Style P5-3

Style P5-6

Style P5-1

Standard Characteristics/Ratings:

ELECTRICAL RATINGS:

Load

Resistive

Inductive

Lamp

Motor

DWV

Low Level

Electrical Life:

Mechanical Life:

Seal:

Operating Force:

Total Travel:

Overtravel:

Sea Level @ 28VDC

or 115VAC, 60/400Hz

10A

1050Vrms

10mA @ 30mV

25,000 cycles

1,000,000 cycles

IP64 & MIL-PRF-8805 Design 2 or IP68S

3.0 lbs. +1/-0.5 lb.

0.180 inches max

0.012 inches min

Features:

• Button sealed with patented “rolling sleeve” principle

• Contact area sealed at case & terminals

• Moistureproof & dusttight to IP64 & MIL-PRF-8805

Design 2 or watertight to IP68S

• Less than 25mΩ contact resistance

• Handles low level up to 10 amps

• Variety of mounting styles

• Engraved buttons available

• Choice of 9 button & 3 bezel colors

• Panel appearance matches most other OTTO

momentary pushbutton switches

• Unsealed construction also available

• RoHS/WEEE/Reach compliant

Operating Temp Range:

-55°C to +85°C

MATERIALS:

Case:

Button:

Terminals:

Terminal Hardware:

Mounting Hardware:

Anodized aluminum alloy

Thermoplastic

Brass, silver plate or gold plate for low level

Terminal lugs, lockwasher and screw for screw terminal option

Hex nut, lockwasher and panel seal on watertight switches

119

OTTO Full Line Catalog

Specifications Subject To Change Without Notice

Recommended Resources

How to design the switching circuit controlled by MCU?

Differential Input Instrumentation Amplifier

One of the soft-start regulated power supply circuits

Three-phase motor phase sequence and phase failure protection circuit

Internal circuit diagram of HM114 thick film circuit

Magnetoresistive element amplifier circuit

Live FAQ｜Fujitsu FRAM non-encryption algorithm (spectrum) authenticity verification solution: Live broadcast details: Fujitsu FRAM's authenticity verification solution without encryption algorithm (spectrum)Live Topic: Fujitsu FRAM Authenticity Verification Solution without Encryption Algorith...; EEWORLD社区 Security Electronics

Based on STM32F303 dual motor FOC driver: sensorless schematic/BOM/code and other open source sharing: [align=center] [b][color=#5E7384]This content is originally created by EEWORLD forum user [size=3]music_586[/size]. If you need to reprint or use it for commercial purposes, you must obtain the author...; music_586 stm32/stm8

(C- Wireless Charging Electric Car) 2018TI Cup Wireless Charging Car: [i=s] This post was last edited by sigma on 2019-4-19 11:20 [/i] [align=left][font=微软雅黑, "][size=14px]I'll just make a fool of myself here~ Due to my limited level and resources at hand, and my poor p...; sigma Electronics Design Contest

Do popular chargers also need double pulse testing? Download the information to learn more and get gifts!: Comprehensive testing of the static and dynamic parameters of the device is very important for the subsequent circuit design of the charger or other functional modules. The B150xA series static parame...; eric_wang Analog electronics

Computer System Architecture Q&A: 1. If the actual flow rate of the channel required by the peripheral is very close to or equal to the maximum flow rate of the channel, local data loss may occur. How can we solve it? (1) Increase the...; 灞波儿奔 Wireless Connectivity

Please recommend a stackup of single-layer FPC with electromagnetic shielding film: Hello everyone, I am designing a flexible circuit board, the basic requirements are as follows: 1. This soft board is installed between the moving parts and the fixed parts, and requires both firmness...; QQ_337007xxx PCB Design

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components