LP311N datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> LP311N

LP311N: Part NumberLP311N; CategoryAnalog mixed-signal IC Amplifier circuit; File Size1577.96，6 Pages; ManufacturerTexas Instruments; Websitehttp://www.ti.com.cn/

Alternative parts

Part Number	Manufacturer	Description
LP311N	Rochester Electronics LLC	Basic information of LP311N amplifier:LP311N is a COMPARATOR. The commonly used packaging method is ...

LP311N Overview

Basic information of LP311N amplifier:

LP311N is a COMPARATOR. Commonly used packaging methods are DIP, DIP8,.3

LP311N amplifier core information:

The minimum operating temperature of LP311N is 70 °C. Its peak reflow temperature is NOT SPECIFIED Its maximum bias current at 25°C is: 0.1 µA Its maximum average bias current is 0.1 µA

When it comes to an amplifier's sensitivity, nothing is better than its nominal response time. The LP311N only takes 1200 ns to complete the response. The maximum slew rate of the LP311N given by the manufacturer is 0.3 mA.

The nominal supply voltage of LP311N is 15 V, and its corresponding nominal negative supply voltage is -15 V. The input offset voltage of LP311N is 7500 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of LP311N:

The width of LP311N is: 7.62 mm and the length is 9.817 mm. LP311N has 8 terminals. Its terminal position type is: DUAL. Terminal pitch is 2.54 mm.

LP311N amplifier additional information:

Its temperature grade is: COMMERCIAL. LP311N is not Rohs certified. The corresponding JESD-30 code is: R-PDIP-T8. The corresponding JESD-609 code is: e0. The packaging code of LP311N is: DIP.

The materials used in LP311N packaging are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR. The form of LP311N package pins is: IN-LINE. Its terminal form is: THROUGH-HOLE. The maximum seat height is 5.08 mm.

Recommended Resources

Electronic ballast circuit using triac dimming

Three-phase motor phase failure operation protection circuit

M131W universal cylindrical grinder electrical schematic circuit

KPY silicon piezoresistive relative pressure sensor circuit 02

Provides a stable bias power supply example circuit diagram

Dual forward converter electrical schematic diagram

CMOS Analog Integrated Circuit Design (Second Edition Chinese Edition): "CMOS Analog Integrated Circuit Design (2nd Edition)" is a classic textbook for analog integrated circuit design courses. Starting from the forefront of CMOS technology, the author combines rich engineering and teaching experience to give a detailed...; arui1999 Download Centre

The development status and key technologies of wireless sensor networks: With the rapid development of wireless communication, integrated circuits, sensors, micro-electromechanical systems and other technologies, the mass production of low-cost, low-power, small-volume, and multifunctional micro sensors has become possi...; Jacktang Wireless Connectivity

NTC thermistor driver for MicroPython: Micropython's NTC thermistor driver, assuming the nominal value of the NTC is 10K, is pulled up to vcc through a 10K resistor R1, and the temperature is calculated after ADC sampling. The default B value is 3380 and the ADC is 12 bits. def ...; dcexpert MicroPython Open Source section

Low voltage light-controlled LED flash light breadboard is OK, but cannot be successfully simulated in Multisim: Low voltage light-controlled LED flash light breadboard is OK, but cannot be successfully simulated in Multisim Attachment 1, original circuit diagram Attachment 2 Breadboard flashes when there is no light Appendix 3 does not run in mul...; 电子路人1 Analog electronics

LCD driver problem: As shown below: Excuse me: 1. [ When M is in a positive cycle (high level), the selection voltage V6 (row drive) or V1 (column drive) is selected. And unselected voltage V2 (row drive) or V3 (column drive)] In this sentence, what ar...; 深圳小花 MCU

Can you help me check if this UL certificate is for an aluminum substrate?: The company is making a product that requires the PCB board to pass UL certification. We have found many PCB manufacturers, but all of them have FR-4 boards that have passed UL certification, but aluminum substrates have not. Finally, we found one t...; PCB我不会 PCB Design

LP311N Also View