LPC661MDA datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> LPC661MDA

LPC661MDA: Part NumberLPC661MDA; CategoryAnalog mixed-signal IC Amplifier circuit; File Size3981.75，19 Pages; ManufacturerNational Semiconductor（TI ）; Websitehttp://www.ti.com

Alternative parts

Part Number	Manufacturer	Description
Sorry, there is no alternative parts yet

LPC661MDA Overview

Basic information of LPC661MDA amplifier:

LPC661MDA is an OPERATIONAL AMPLIFIER. Commonly used packaging methods are DIE, DIE OR CHIP

LPC661MDA amplifier core information:

The minimum operating temperature of the LPC661MDA is -40 °C and the maximum operating temperature is 85 °C.

How to simply check the efficiency of an amplifier? Looking at its slew rate, the nominal slew rate of LPC661MDA is 0.11 V/us. The maximum slew rate of the LPC661MDA given by the manufacturer is 0.105 mA, while the minimum slew rate is 0.03 V/us. Its minimum voltage gain is 40000. When the op amp is used in a closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the LPC661MDA gain becomes 0.707 times the low-frequency gain is 350 kHz. The power of LPC661MDA is NO. Its programmable power is NO.

The nominal supply voltage of LPC661MDA is 5 V, and its corresponding nominal negative supply voltage is. The input offset voltage of LPC661MDA is 6300 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of LPC661MDA:

Its terminal position type is: UPPER.

LPC661MDA amplifier additional information:

LPC661MDA adopts the VOLTAGE-FEEDBACK architecture. It belongs to the low-bias class of amplifiers. It does not belong to the low offset class of amplifiers. The frequency compensation status of LPC661MDA is: YES. Its temperature grade is: INDUSTRIAL.

It is a micropower amplifier. The corresponding JESD-30 code is: X-XUUC-N. The packaging code of LPC661MDA is: DIE. The materials used in the LPC661MDA package are mostly UNSPECIFIED. The package shape is UNSPECIFIED.

The LPC661MDA package pin format is: UNCASED CHIP. Its terminal forms are: NO LEAD.

Recommended Resources

Electric energy measurement circuit a

Stabilized power supply circuit that can be controlled by external signals

One of the mains undervoltage and overvoltage protection circuits

ZF three-phase motor commutation component reversible motor circuit

Load current limiting circuit

Two-stage phase-shift oscillator circuit diagram using CMOS gate circuit

How should the potential of each power supply of a switching power supply be set?: Suppose taking a frequency converter main circuit power supply circuit as an example, the three-phase AC is rectified into DC 540V, the switching power supply draws power from the positive and negative bus bars, and the switching power supply has mu...; 乱世煮酒论天下 Switching Power Supply Study Group

msp430f5529 simple uart source program (use the serial port assistant to send and receive replies): The MCU source program is as follows: /*****What to send with the serial assistant and what to reply****/ #include "msp430f5529.h" // ACLK = REFO = 32768Hz, MCLK = SMCLK = default DCO/2 = 1048576Hz // P3.4，5——USCI_A0 TXD/RXD；P9.4,5——...; Aguilera Microcontroller MCU

In this full-bridge LLC circuit, is the circled part the RC buffer circuit of the gate source?: Why is the resistor not connected in series with the gate G? And how is the RC parameter determined? I saw a case where the value was adjusted from 20Ω/2200pF to 2Ω/1000pF. Isn't this a big span? Is it limited by the RC product? Or is it an empirica...; 西里古1992 Analog electronics

What are the screw holes in this package for?: I found this today when I was organizing the package library. What is this screw hole called? What is it used for? This is called the guard hole. It prevents the copper sheet from curling up and ensures good grounding. If there were no holes...; sfcsdc PCB Design

Using debug macro definition to turn on/off debug output in C/C++: debug macro as debug switch When writing a program, in order to debug, you often need to add some output statements, and then comment them out after debugging is completed. If you need to debug next time, you have to uncomment them, which is ver...; Aguilera Microcontroller MCU

[TI recommended course] #Innovation of general-purpose op amp and comparator chips#: //training.eeworld.com.cn/TI/show/course/5674 Recently I keep seeing netizens recommending courses, and then I realized that it is actually an activity. But the recommended courses are good. ...; glorys TI Technology Forum

LPC661MDA Also View