EL5327CRZ datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> EL5327CRZ

EL5327CRZ: Part NumberEL5327CRZ; CategoryAnalog mixed-signal IC Amplifier circuit; File Size2910.82，17 Pages; ManufacturerRenesas Electronics Corporation; Websitehttps://www.renesas.com/; Environmental Compliance

Alternative parts

Part Number	Manufacturer	Description
EL5327CRZ-T7	Renesas Electronics Corporation	Basic information of EL5327CRZ-T7 amplifier:EL5327CRZ-T7 is a BUFFER from Intersil. Commonly used pa...
EL5327CRZ-T13	Renesas Electronics Corporation	Basic information of EL5327CRZ-T13 amplifier:EL5327CRZ-T13 is a BUFFER from Intersil. Commonly used ...
EL5327CR-T13	Renesas Electronics Corporation	Basic information of EL5327CR-T13 amplifier:EL5327CR-T13 is a BUFFER. The commonly used packaging me...
EL5327CR	Renesas Electronics Corporation	...
EL5327CR-T7	Renesas Electronics Corporation	IC OPAMP BUFFER 2.5MHZ 24TSSOP

EL5327CRZ Overview

Basic information of EL5327CRZ amplifier:

EL5327CRZ is a BUFFER from Intersil. Commonly used packaging methods are SOP, TSSOP24,.25

EL5327CRZ amplifier core information:

The minimum operating temperature of EL5327CRZ is -40 °C and the maximum operating temperature is 85 °C. Its peak reflow temperature is 260°C. Its maximum bias current at 25°C is: 0.05 µA. Its maximum average bias current is 0.05 µA.

The maximum slew rate of the EL5327CRZ given by the manufacturer is 2.1 mA, while the minimum slew rate is 0.9 V/us. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the EL5327CRZ gain becomes 0.707 times the low-frequency gain is 2.5 MHz.

The nominal supply voltage of EL5327CRZ is 5 V, and its corresponding nominal negative supply voltage is -5 V. The input offset voltage of EL5327CRZ is 15000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of EL5327CRZ:

The width of EL5327CRZ is: 4.4 mm and the length is 7.8 mm. EL5327CRZ has 24 terminals. Its terminal position type is: DUAL. Terminal pitch is 0.65 mm. Total pins: 24, 24

EL5327CRZ amplifier additional information:

Its temperature grade is: INDUSTRIAL. And its humidity sensitivity level is: 3. EL5327CRZ is not Rohs certified. The corresponding JESD-30 code is: R-PDSO-G24. The corresponding JESD-609 code is: e3.

The packaging code of EL5327CRZ is: SOP. The materials used for EL5327CRZ packaging are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR. The EL5327CRZ package pin forms are: SMALL OUTLINE. Its terminal forms are: GULL WING.

The maximum seat height is 1.2 mm.

Recommended Resources

Flash light toy circuit made of transistor oscillator

LM3420-8.4 special lithium battery charger

TDA1551Q power amplifier circuit diagram

Photometry circuit diagram using AC amplifier

Charger circuit with current limiting protection

Computer motherboard circuit diagram 815 4_65

Shanghai International Embedded World - 16-axis motion control solution based on Raspberry Pi 5 and CODESYS: During the three-day Shanghai International Embedded World, Raspberry Pi and Shanghai Jingheng jointly demonstrated numerous solutions based on Raspberry Pi and CODESYS. Friends who have not been to the exhibition site must not miss this article! ...; 树莓派开发者 Integrated technical exchanges

Read the good book "Operational Amplifier Parameter Analysis and LTspice Application Simulation" for free, take notes, and master the knowledge of operational amplifiers thoroughly: April Reading Festival, good books will enlighten the world~hello, everyone~I am here to urge progress and encourage everyone to read good books. I recommend good books to you all, okhxyyo~Come and read books together to learn knowledge~~ This tim...; okhxyyo Analog electronics

[National Technology N32WB031_STB development board review] GPIO flip performance test: N32WB03x GPIO flip performance test Preface In some cases, GPIO is needed to simulate some peripherals, although this will take up more MCU. In order to find out the upper limit of the MCU's GPIO flip speed, it is still necessary to test it. O...; walker2048 RF/Wirelessly

[MicroPython] STM32 branch fixes a CDC problem when USB is reconnected: Characters are not retransmitted if USB is reconnected. Prior to this change, if USB was reconnected, some characters in the TX buffer might be retransmitted, fixed by preserving the TX buffer state between reconnects. https://github.com/micropython/...; dcexpert MicroPython Open Source section

MSP430fr6989 serial port DMA sending experimental routine: In this example, P2.0 and P2.1 of MSP430fr6989 are selected as serial ports UCA0TXD and UCA0RXD; (There is not much code, mainly for register operations, and it is written in the main.c file in a hurry. It is not recommended to do this for enginee...; fish001 Microcontroller MCU

NXP Technology Days Tour Seminar Guangzhou Station invites you to sign up!: NXP Technology Days Seminar focuses on cutting-edge enabling technologies, covering popular applications such as automotive electronic architecture, ADAS, automotive electrification, in-vehicle infotainment systems, UWB ultra-wideband, smart in...; eric_wang Automotive Electronics

EL5327CRZ Also View