EL5327CRZ-T7 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> EL5327CRZ-T7

EL5327CRZ-T7: Part NumberEL5327CRZ-T7; CategoryAnalog mixed-signal IC Amplifier circuit; File Size5252.58，12 Pages; ManufacturerRenesas Electronics Corporation; Websitehttps://www.renesas.com/; Environmental Compliance

Alternative parts

Part Number	Manufacturer	Description
EL5327CRZ	Rochester Electronics LLC	Basic information of EL5327CRZ amplifier:EL5327CRZ is a BUFFER. The commonly used packaging method i...
EL5327CRZ-T13	Renesas Electronics Corporation	Basic information of EL5327CRZ-T13 amplifier:EL5327CRZ-T13 is a BUFFER from Intersil. Commonly used ...
EL5327CR-T13	Renesas Electronics Corporation	Basic information of EL5327CR-T13 amplifier:EL5327CR-T13 is a BUFFER. The commonly used packaging me...
EL5327CR	Renesas Electronics Corporation	...
EL5327CR-T7	Renesas Electronics Corporation	IC OPAMP BUFFER 2.5MHZ 24TSSOP

EL5327CRZ-T7 Overview

Basic information of EL5327CRZ-T7 amplifier:

EL5327CRZ-T7 is a BUFFER from Intersil. Commonly used packaging methods are SOP, TSSOP24,.25

EL5327CRZ-T7 amplifier core information:

The minimum operating temperature of EL5327CRZ-T7 is -40 °C and the maximum operating temperature is 85 °C. Its peak reflow temperature is 260°C. Its maximum bias current at 25°C is: 0.05 µA. Its maximum average bias current is 0.05 µA.

The maximum slew rate of the EL5327CRZ-T7 given by the manufacturer is 2.1 mA, while the minimum slew rate is 0.9 V/us. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the EL5327CRZ-T7 gain becomes 0.707 times the low-frequency gain is 2.5 MHz.

The nominal supply voltage of EL5327CRZ-T7 is 5 V, and its corresponding nominal negative supply voltage is -5 V. The input offset voltage of EL5327CRZ-T7 is 15000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of EL5327CRZ-T7:

The width of EL5327CRZ-T7 is: 4.4 mm and the length is 7.8 mm. EL5327CRZ-T7 has 24 terminals. Its terminal position type is: DUAL. Terminal pitch is 0.65 mm. Total pins: 24, 24

EL5327CRZ-T7 amplifier additional information:

Its temperature grade is: INDUSTRIAL. And its humidity sensitivity level is: 3. EL5327CRZ-T7 is not Rohs certified. The corresponding JESD-30 code is: R-PDSO-G24. The corresponding JESD-609 code is: e3.

The packaging code of EL5327CRZ-T7 is: SOP. EL5327CRZ-T7 packaging materials are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR. The EL5327CRZ-T7 package pin format is: SMALL OUTLINE. Its terminal forms are: GULL WING.

The maximum seat height is 1.2 mm.

Recommended Resources

Stable brightness dimmer circuit 2

SC3071 touch step dimming light circuit

RF Tuned Amplifier Circuit Diagram B

Temperature sensor circuit with transformer isolation

Automatic sequential power on control circuit diagram

Touch type thyristor zero-crossing switch circuit diagram

Please advise, is it necessary to consider the safety power when calculating the LED resistance?: For example, if the resistance of an LED is 4K, the current is 5mA, and the voltage is 24V, then the resistance power is 0.1W. I usually use 0805, which is 0.125W. What does the safety resistance in the figure mean, which is 0.167W? How is it calcul...; sky999 PCB Design

There are 10 components used to produce a certain product, and the failure rates of 3 of them are 1%, 2%, and 3% respectively. What is the failure rate of the final product?: There are 10 components used in the production of a certain product, and the unqualified rates of 3 of them are 1%, 2%, and 3%, respectively, while the qualified rates of the remaining components are 100%. How to calculate the unqualified rate of...; 深圳小花 MCU

That green PCB board is tested with these 7 methods: The process of electronic hardware design includes hardware requirements, schematic design, PCB design, PCB manufacturing, UT and integrated testing, etc. Among them, in the PCB board processing and manufacturing link, in order to ensure the producti...; mwkjhl PCB Design

[Domestic Tang Primer 25K Review] A simple example of expansion peripherals based on E203 - the first hardware layer: The last issue demonstrated how to simply transplant E203 to the Tang25K development board. This time, I will simply demonstrate how to add peripherals to the E203 soft core. There are certain problems, that is, there are problems with address offse...; 学学学学学学学 Domestic Chip Exchange

C28x Software Tips: How to View Software Examples and Documentation: Where can I find peripheral examples, math libraries, DSP, or DigitalPower examples? Reference the following information on the ti.com website: C2000 Getting Started Guide – Software - Learn about C2000Ware, C2000Ware, and C2000Ware. 102)] controlSUI...; 灞波儿奔 Microcontroller MCU

Teach you how to use the CSK6 development board to connect to ChatGPT: Introduction: This post introduces how to use the CSK6 large model development board to connect to ChatPT to make an AI assistant that can interact with voice. The current solution is to use the development kit as the input end, and upl...; 胡黎明 DIY/Open Source Hardware

EL5327CRZ-T7 Also View