TLV2372QDGKRQ1 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> TLV2372QDGKRQ1

TLV2372QDGKRQ1: Part NumberTLV2372QDGKRQ1; CategoryAnalog mixed-signal IC Amplifier circuit; File Size17173.06，42 Pages; ManufacturerTexas Instruments; Websitehttp://www.ti.com.cn/

Alternative parts

Part Number	Manufacturer	Description
TLV272QDGKRQ1	Texas Instruments	DUAL OP-AMP, 7000uV OFFSET-MAX, 2.4MHz BAND WIDTH, PDSO8, MSOP-8
TLV2372MDGKREP	Texas Instruments	TLV2372MDGKREP amplifier basic information:TLV2372MDGKREP is an OPERATIONAL AMPLIFIER. The commonly ...

TLV2372QDGKRQ1 Overview

TLV2372QDGKRQ1放大器基础信息：

TLV2372QDGKRQ1是一款OPERATIONAL AMPLIFIER。常用的包装方式为VSSOP-8

TLV2372QDGKRQ1放大器核心信息：

TLV2372QDGKRQ1的最低工作温度是-40 °C，最高工作温度是125 °C。25℃下的最大偏置电流为：0.00006 µA他的最大平均偏置电流为0.00006 µA

如何简单看一个放大器效率？看它的压摆率，TLV2372QDGKRQ1的标称压摆率有2.4 V/us。厂商给出的TLV2372QDGKRQ1的最大压摆率为2.4 mA，而最小压摆率为1 V/us。其最小电压增益为6300。而在运放闭环使用时，某个指定闭环增益（一般为 1 或者 2、 10 等）下，TLV2372QDGKRQ1增益变为低频增益的 0.707 倍时的频率为3000 kHz。TLV2372QDGKRQ1的功率为NO。其可编程功率为NO。

TLV2372QDGKRQ1的标称供电电压为5 V。而其供电电源的范围为：+-1.35/+-8/2.7/16 V。TLV2372QDGKRQ1的输入失调电压为6000 µV（输入失调电压：使运算放大器输出端为0V(或接近0V)所需加于两输入端之间的补偿电压。）

TLV2372QDGKRQ1的相关尺寸：

TLV2372QDGKRQ1的宽度为：3 mm，长度为3 mmTLV2372QDGKRQ1拥有8个端子.其端子位置类型为：DUAL。端子节距为0.65 mm。共有针脚：8

TLV2372QDGKRQ1放大器其他信息：

TLV2372QDGKRQ1采用了VOLTAGE-FEEDBACK的架构。其属于低偏置类放大器。其不属于低失调类放大器。TLV2372QDGKRQ1的频率补偿情况是：YES。其温度等级为：AUTOMOTIVE。

其不属于微功率放大器。其对应的的JESD-30代码为：S-PDSO-G8。TLV2372QDGKRQ1的封装代码是：TSSOP。TLV2372QDGKRQ1封装的材料多为PLASTIC/EPOXY。而其封装形状为SQUARE。

TLV2372QDGKRQ1封装引脚的形式有：SMALL OUTLINE, THIN PROFILE, SHRINK PITCH。其端子形式有：GULL WING。座面最大高度为1.1 mm。

Recommended Resources

FM radio circuit diagram using FET

Interface circuit of remote control transmitter

Touch delay switch circuit

Programmable counter

IGD508E/IGD515E application circuit

MSP430 Launchpad MSP430g2452 SHT10 Temperature and Humidity Sensor: SHT10 temperature and humidity sensor on MSP430 Launchpad MSP430g2452 platform //********************************File Information******************************* //** File Name: Sht10.c //** Platform: MSP430 LaunchPad MSP430G2452 //** System Fun...; Aguilera Microcontroller MCU

[Anxinke NB-IoT Development Board EC-01F-Kit] 4. Serial port MQTT networking and information sending and receiving test: In the application of Internet of Things, MQTT transmission is very common, and most of my works also use MQTT for transmission. First, open the NB-IOT AT manual and look at the section 3.5 MQTT commands. There are not many commands, and no r...; kit7828 RF/Wirelessly

[NXP Rapid IoT Review] + Rapid IOT Kit Review Summary: The end date of the evaluation has arrived, and it is time to summarize this evaluation. First, let me talk about the advantages and disadvantages of this kit, and then summarize the development process and the regrets after the evaluation. Advantage...; manhuami2007 RF/Wirelessly

How to improve EMI of circuit boards by placing components?: After designing the circuit structure and device location, PCB EMI control becomes extremely important for the overall design. How to avoid PCB electromagnetic interference in switching power supplies has become a topic of great concern to developer...; Aguilera Analogue and Mixed Signal

Anlogic register garbled?: Normally, the firmware should be able to enter normal working state immediately after burning, but in some cases, it does not work immediately after burning. When checking with chipwatcher, it will be found that the registers are garbled. Sometime...; 黑屋白巫 EE_FPGA Learning Park

Standards and control circuits for electric vehicle charging interfaces: The reference standard parts of China's electric vehicle standard charging interface and handshake circuit are GB/T 20234 and GB/T 18487.1 respectively. The maximum voltage of the AC charging interface is three-phase 440V AC, and t...; 火辣西米秀 Automotive Electronics

TLV2372QDGKRQ1 Also View