Buck converter using optical feedback to control white LED
Source: InternetPublisher:清宁时光 Keywords: LED circuit buck regulator Updated: 2024/07/19
Lighting using LEDs has gained more attention due to the availability of high-power, high-efficiency white (and other color) LEDs (Reference 1). Since LEDs are current-controlled devices, the typical control circuit adjusts the current through the LED to maintain consistent brightness. To make the best use of the power, users often use switching converter circuits for LEDs, which can be either buck or boost converters, depending on the input DC voltage. Figure 1 shows the structure of a typical buck and boost converter white LED driver circuit. White LEDs add a series resistor, R, which determines the current through the LED. The value of the resistor depends on the required LED current and the feedback voltage required by the buck/boost converter. For example, an average current of 100mA through the LED and a feedback voltage of 1.23V require a resistor value of 12Ω. To reduce the power dissipated in the series resistor, engineers typically use the circuit structure shown in Figure 2. In this circuit, the gain of the amplifier reduces the power dissipated in the series resistor by a factor equal to the gain (Reference 2).
The circuit configurations in Figures 1 and 2 work well for regulating the current through the LED, provided that the ambient temperature remains constant. However, the brightness of white and other color LEDs is a function of temperature and varies greatly with temperature (References 2 and 3). Over a temperature range of 100°C, the brightness varies from 40% to 150%. Therefore, if changes in ambient temperature are expected, it is not sufficient to regulate only the current through the LED.
is not an effective way to control an LED. An alternative is to use optical feedback to control the LED (Reference 3).
However, instead of using an expensive light sensor and amplifier circuit, a suitable LED can be used as a light sensor (Reference 4). Figure 3 shows a white LED controller using an inexpensive buck regulator IC (the adjustable LM2575). A 3-mm red LED in a clear package is used to detect the light from the 10-mm white LED. The spectrum of the white LED is broad enough to excite the red LED used as a sensor. For a 60-mA test current through the white LED, the voltage across the red LED sensor is approximately 40 mV. Because the circuit uses the voltage across the red LED sensor as feedback to the buck regulator, an amplifier with a gain of approximately 30 must be used because the internal reference voltage of the LM2575 buck regulator is 1.23 V. Resistors R1, R2, and R3 control the gain of the amplifier, which consists of an inexpensive LM358 dual op amp. The input DC voltage powers the op amp. The resistance values of resistors R1, R2, and R3 are 270Ω, 560Ω, and 10kΩ, respectively. Since R2 is a variable resistor, changing its setting value changes the gain, and thus changes the current through the white LED. Therefore, R2 is used for brightness control. The amplifier gain ranges from 28 to 84, depending on the setting of R2.
The red LED acts as a sensor and is mounted to the side of the white LED, so only a portion of the white LED's radiated light is used. The top of the 3mm red LED is processed into a flat surface, and then the 3mm red LED is fixed to the side of the white LED with a drop of super glue.
The LM2575 buck regulator adjusts the output voltage by changing its duty cycle. If the output light intensity of the white LED decreases due to temperature rise, the voltage of the red LED sensor also decreases proportionally. The output of the red LED sensor is connected to the feedback input terminal (pin 4) of the regulator IC, and the regulator IC accordingly increases the output voltage duty cycle of the white LED, thereby stabilizing the brightness. When the ambient temperature drops, the light intensity of the white LED increases, and the regulator reduces the output voltage, which also achieves the purpose of stabilizing the brightness of the white LED.
References
1. Saab, Alfredo H, and Steve Logan, "High-power LED drivers require no external switches," EDN, July 19, 2007, pg 78.
2. "Specifications for Nichia Warm White LED," Nichia Corp.
3. Santos, Bjoy, "Optical feedback extends white LEDs' operating life," EDN, Jan 18, 2007, pg 84.
4. Gadre, Dhan anjay, and Sheetal Vashist, “LED senses and displays ambient-light intensity,” EDN, Nov 9, 2006, pg 125.
- Circuit diagram of a differential amplifier circuit
- Frequency divider that converts 50Hz or 60Hz frequency into 1/60 frequency (CD4040)
- Using Monostable Trigger to Construct Pulse Delay Circuit
- Simple and easy to make energy-saving LED flashlight
- A night light made of LED
- Power-saving LED dimming circuit
- 915MHz RF amplifier circuit composed of RF2103P
- Analog Karaoke Accompaniment Amplifier Circuit
- Triode Single Stage Amplifier
- Human body bioelectric signal preamplifier composed of INA102
- Capacitor step-down LED drive circuit diagram using varistor
- LED light circuit diagram
- Novel solar LED light controller circuit diagram
- Automotive LED driver circuit diagram using LT3486
- NCP1014/1028 driver LED circuit diagram
- MAX16834 driver LED circuit diagram
- Capacitor Buck Regulator Power Supply Circuit Diagram
- MIC2298 driving LED circuit diagram
- Low battery flash LED circuit
- LM3578A used as a buck regulator circuit diagram