• Duration:33 minutes and 42 seconds
  • Date:2017/01/03
  • Uploader:老白菜
Introduction
This course mainly focuses on learning mathematics from the following aspects:

1. Basic logic gate circuits (AND gate, OR gate, NOT gate, XOR gate, NAND gate, NOR gate, AND NOR gate; 0C gate, OD gate, three-state gate, CMOS transmission gate)

2. Combinational logic gate circuit test (analyze the logic function according to the circuit, design the corresponding functional logic circuit, fire alarm system, and four-person voting device according to the topic requirements)

3. Encoder and decoder (Encoder, decoder, trigger, counter)

4. Digital circuit design (answer design, simple stopwatch, simple password lock, simple frequency tester)
Unfold ↓

You Might Like

Recommended Posts

Smart power monitoring and protection system creative progress post + PCB original file (supplement)
[i=s]This post was last edited by ltbytyn on 2014-5-17 22:10[/i] I uploaded a reduced schematic before. Since the branch sampling circuits are exactly the same, I was in a hurry to get the drawing out
ltbytyn Renesas Electronics MCUs
DSP is burned into Flash, the simulation can run, but it cannot run after unplugging the simulator and restarting it
DSP is burned into Flash, the simulation can run, it can run without power failure and unplugging the emulator, but it cannot run after power failure and restart. At this time, just connect the emulat
kai182 Microcontroller MCU
Help!!!! Can anyone share some Renesas programs?
[i=s]This post was last edited by paulhyde on 2014-9-15 03:22[/i] I am learning Renesas from scratch and I don’t have any programs. . . . . . . . . . . Please share:Cry: :Cry: :Cry:
310069704 Electronics Design Contest
How do circuits remember data?
Does anyone know the principle of memory circuits? What are the circuits with memory function? What books can I read to find the answer?
hhhh512mail TI Technology Forum
What to pay attention to when choosing an embedded training institution
1. Understand the teaching staff of the training institution. This is the most important point for trainees. Every institution will say that its teaching staff is very good, but can it actually let tr
ceec2012 Embedded System
Detailed explanation of t6963 instructions
I have been working on LCD modules recently. Many LCD modules are controlled by T6963. Many LCD PDF documents do not provide detailed introduction to T6963 control instructions. Here is a detailed exp
sdewen911 Analog electronics

推荐文章

简仪计数器/定时器模块满足严格的工业标准和安全要求 2024年10月17日
应用 在电气开关柜的控制模组中,精确的时延控制对于确保高电压设备的安全运行至关重要。控制模组需要输出固定时延的脉冲信号,以控制外部的高电压设备。这种应用场景要求脉冲信号的时延精度达到10 ns级别,以满足严格的工业标准和安全要求。 挑战 传统的脉冲边沿检测方法通常采用示波器或时间间隔计时器等仪表进行测量,但这些方法存在精度不够高、测量速度慢、操作繁琐等弊端,难以满足高压控...
油液颗粒计数器在工业自动化进程中带来的巨大效益 2024年09月11日
现代化工业中,越来越多的先进科学技术应用到自动化工业中,很多不同的行业因此也感受到先进科技带来的便捷和产生的巨额利润,因为高科技产品让工作人员在做一些数据或者其他测试时变得事半功倍。 在工业自动化的过程中中我们离不开对各种油液的日常监测,今天我们简单的探讨一下油液颗粒计数器,这种计数器主要应用于油液分析,可以对油液颗粒度、清洁度、污染物监测和分析,能够依据NAS1638、...
MCS-51单片机定时器/计数器常见习题解答 2024年08月30日
1、根据定时器/计数器0方式1逻辑结构图,分析门控位GATE取不同值时,启动定时器的工作过程。 答:当GATE=0:软件启动定时器,即用指令使TCON中的TR0置1即可启动定时器0。 GATE=1:软件和硬件共同启动定时器,即用指令使TCON中的TR0置1时,只有外部中断INT0引脚输入高电平时才能启动定时器0。 2、当定时器/计数器的加1计数器计满溢出时, 溢出标志位T...
利用AT89S51单片机的T0、T1的定时计数器功能 2024年08月30日
利用AT89S51单片机的T0、T1的定时计数器功能,来完成对输入的信号进行频率计数,计数的频率结果通过8位动态数码管显示出来。要求能够对0-250KHZ的信号频率进行准确计数,计数误差不超过±1HZ。 1. 电路原理图 2. 系统板上硬件连线 (1). 把“单片机系统”区域中的P0.0-P0.7与“动态数码显示”区域中的ABCDEFGH端口用8芯排线连接。...

Recommended Content

可能感兴趣器件

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews


Room 1530, 15th Floor, Building B, No.18 Zhongguancun Street, Haidian District, Beijing, Postal Code: 100190 China Telephone: 008610 8235 0740

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号