• You can log in to your eeworld account to continue watching:
  • STM32Cube HAL theory GPIO - Lab GPIO2 read pin manuall
  • Login
  • Duration:16 minutes and 13 seconds
  • Date:2020/03/13
  • Uploader:桂花蒸
Introduction
keywords: PWM STM32 DMA CubeMX HAL
This MOOC is targeting anyone who starts working on STM32 by introducing STM32 ecosystem.  You need some knowledge in C programming, and a NUCLEO-F401RE board for the hands-on.

Welcome to STM32Cube basics training! 
In this course we want to present you how to work with STM32 ecosystem. The course is focused on explanation of STM32CubeMX tool, how to handle basic tasks and use tool for basic project creation.
 
The course is structured in two parts. The first part is related to STM32CubeMX and MCU configuration:
- STM32 selection
- Pin-out configuration
- Clock configuration
- Peripheral configuration
- Power calculator
- Project generation settings

 The second part is related to STM32Cube HAL library which is used for developing your application:
- HAL library structure
- Handles and callbacks
- Interrupts
- DMA
- Basic HAL usage

All these points are developed in presentation and hands-on.

What are the requirements?
You need some knowledge of C programming language and a NUCLEO-F401RE board for the hands-on (please refer to your local ST distributor for an offer).

What am I going to get from this course?
Understand STM32CubeMX tool, and be able to work with STM32Cube HAL library and navigate in its structure

What is the target audience?
Anyone who wants to start developing on STM32 MCUs and never worked with STM32CubeMX and the HAL library. Or for someone who worked with previous standard peripheral library on ST products and wants to understand the STM32Cube ecosystem.
Unfold ↓

You Might Like

Recommended Posts

pl2303 driver under CE6
Hello everyone, I bought a USB to serial GPS receiver, which uses a pl2303 conversion chip inside. It converts the serial port to USB. But under the CE6 system, I can't install the driver and can't us
guanliheng Embedded System
Is it possible for the LDO or DCDC output voltage to be lower than the internal reference voltage?
Generally, the output voltage of the regulator is divided by a resistor and compared with the internal reference voltage. Thereby adjusting the output voltage to reach the desired voltage value. Howev
sfcsdc Analog electronics
Mi Rabbit Building Block Robot Unboxing
[i=s]This post was last edited by supermiao123 on 2016-11-16 10:11[/i] [url=http://www.mi.com/toyblock/?cfrom=search]http://www.mi.com/toyblock/?cfrom=search[/url] I'll post a URL first. I saw a new p
supermiao123 Talking
Setup program, help
The MCU sets the wireless module, but does not issue a command and returns an OK. Could you please help me look at this program? Thank you. void coordinator_set() { wireless_str("+++"); if(strcmp(reok
emily_1105 RF/Wirelessly
430 Calculate 64-bit multiplication and division problems
I used 430 to calculate a 64-bit by 16-bit division, and found that the code increased a lot. Before adding this division, the code length was 0x614, and after adding it, it became 0x1556. I know the
jishuaihu Microcontroller MCU
About a single chip stopwatch program
Today, I wrote a single-chip stopwatch based on other people's ideas. The display is 00.00-99.99, but only two digits are displayed in the simulation. The other two digits are not displayed. ORG 0000H
zx258 MCU

Recommended Content

Circuit

可能感兴趣器件

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews


Room 1530, 15th Floor, Building B, No.18 Zhongguancun Street, Haidian District, Beijing, Postal Code: 100190 China Telephone: 008610 8235 0740

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号