Training

Location:Training / Embedded Development / MCU / Punctual Atomic teaches you step by step how to learn STM32-M4 / IO pin multiplexing and mapping

You can log in to your eeworld account to continue watching：
IO pin multiplexing and mapping
Login

Duration：19 minutes and 13 seconds
Date：2019/03/21

Uploader：EE大学堂

Introduction

keywords： Microcontroller STM32 Punctual Atom

This video will lead you from the basic to the more advanced to learn the various functions of STM32F4 and start a new STM32 journey for you.
This video is divided into three parts:
1. Introductory part, which mainly introduces the basic knowledge of STM32;
2. Intermediate part, mainly introduces the use of STM32 basic peripherals, including: GPIO, serial port, timer, external interrupt, etc. After studying this article, you will have a basic introduction to STM32 development.
3. Advanced chapter, mainly introduces STM32 advanced peripherals, including: SDIO, CAN bus, etc.

You Might Like

Recommended Posts

Help with motor drive wiring problem: [i=s]This post was last edited by nnnf on 2019-10-14 16:52[/i]As the title says, I want to use xpctarget to control maxon motor through NI6289 board. The motor is equipped with epos2 driver. xpcTarget; nnnf Motor Drive Control（Motor Control）

Please tell me how to use ADC10DTC in ADC10: Can anyone explain how to use the ADC10 of G2553 and its built-in ADC10DTC, including how to get the value (e.g., repeat single-channel mode)? It would be best if there is an example. Thank you...; Domen Microcontroller MCU

Is there a program to test the read and write speed of TMS320F2812 external SRAM?: [i=s] This post was last edited by Xiaoan on 2015-3-6 11:26 [/i] Delete the post. Delete the post. I wrote a program myself. It is actually quite simple.; 小an Microcontroller MCU

How many pulses does a 2048PPR encoder send in one revolution?: I would like to ask everyone, the Tamaga servo motor uses a 2048PPR encoder. How many pulses does it send in one revolution? Is it 2048*4=8192? Or 8000? If it is 8192, wouldn't it be very inconvenient; eeleader Industrial Control Electronics

Why is LCD1602 always busy when setting the display position?: Recently, I encountered a problem when adjusting 1602: when the display position is not added, the LCD displays normally. Once I want to set the display position, for example, to display characters in; chent1984 Embedded System

《VLMC Laser Engraving Machine》 1. Project Introduction: [i=s]This post was last edited by kejoy on 2015-6-4 23:09[/i] [align=center][/align] [align=center][/align] [align=center][media=x,500,375]http://v.youku.com/v_show/id_XOTU2NzY0ODIw.html/v.swf.html[/m; kejoy DIY/Open Source Hardware

Recommended Content

Hot VideosMore

Hot ArticlesMore

Circuit

可能感兴趣器件

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews

Room 1530, 15th Floor, Building B, No.18 Zhongguancun Street, Haidian District, Beijing, Postal Code: 100190 China Telephone: 008610 8235 0740

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函

京公网安备 11010802033920号