Training
Profile
In this video I show how to measure the gain and phase response of a flyback. I used the Venable frequency response analyzer to measure the stability of the flyback converter. The datasheet shows a crossover or bandwidth of 7KHz. But the Venable shows it to be only about 54 Hz. So always try to verify your components specification.
Chapters
Unfold
You Might Like
Recommended Posts
- China's first batch of autonomous driving unmanned commercial licenses issued! Do you dare to sit in an unmanned car? ?
- Guan Guan's phone just sent me a message:Guan Guan’s first reaction was: Wow, technology is developing so fast, is this commercialization? ? The second reaction is the safety issue. Is it reliable? Wh
-
okhxyyo
Automotive Electronics
- GDB debugging and DSP
- I would like to ask if anyone has used GDB to debug DSP bare-metal programs. I am not referring to the traditional Debug function provided on CCS, but running the GDB program on the PC and debugging t
-
TWWT
DSP and ARM Processors
- The IO pin of MSP430 is set as input, but it receives the output signal of the Hall sensor, and the chip-side signal does not switch.
- The IO pins P2.0, P2.2 and P2.6 of MSP430 are set as inputs, but they receive the output signal of the Hall sensor. After the program is run, the motor is rotated manually (the Hall element of the mot
-
Scaler-y
Microcontroller MCU
- [Serial] [Starlight Lightning STM32F407 Development Board] Chapter 10 Serial Communication Experiment
- Chapter 11 Serial Port Communication Experiment 11.1 Purpose Through this experiment, you will master the use of STM32 serial port and realize sending and receiving data through the serial port. For t
-
hejecu
stm32/stm8
- Where do errors in vector network analyzers come from?
- The error sources of vector network analyzers are mainly the following three aspects: drift error, random error, and systematic error.1. Drift error: It is caused by changes in the performance of the
-
博宇讯铭
Test/Measurement
- [Perf-V Evaluation] Environment Construction and Marquee Program Running
- [i=s]This post was last edited by superstar_gu on 2021-1-29 16:04[/i]2.2.1 Setting up the Vivado hardware development environmentThe core processing chip of the Perf-V development board uses the Xilin
-
superstar_gu
EE_FPGA Learning Park
Recommended Content
Web users are watching Change
- China's first batch of autonomous driving unmanned commercial licenses issued! Do you dare to sit in an unmanned car? ?
- GDB debugging and DSP
- The IO pin of MSP430 is set as input, but it receives the output signal of the Hall sensor, and the chip-side signal does not switch.
- [Serial] [Starlight Lightning STM32F407 Development Board] Chapter 10 Serial Communication Experiment
- Where do errors in vector network analyzers come from?
- [Perf-V Evaluation] Environment Construction and Marquee Program Running
- The relationship between serial port communication and interruption
- How to use a wiring harness tester to measure small resistance? Here's a method
- Those who don't know about RF MEMS, please take a look. This is what the technology is like.
- General Design Considerations for Embedded Systems
- Download the NI white paper "Overcoming the Challenges of Production Test for Complex Devices Under Test" for free and get a chance to win prizes!
- Surge protection for MOSFET DC switches
- #The best content of the "Interview with famous teachers" in the electronic competition#The first issue - Professor Hu Renjie of Southeast University
- BlueNRG-LP uses RNG function in static protocol stack and cannot broadcast
- Power Supply Ripple Measurement Setup (Oscilloscope)
- c8051F060 program download problem
- 1
- Thermistor, hysteresis resistor, gas resistor, varistor, photoresistor application circuit collection
- Can a bandpass filter be powered from a single supply?
- Discussion on Graphical Programming Method of Single Chip Microcomputer
- Op amp problem
- MSP430 MCU Basics
- Evaluation Invitation Ticket Record Form
- How does a MCU software engineer write simple computer software?
- Smart IoT Student Dormitory Based on RSL10
- [Voice and vision module based on ESP32S3] Software development progress - module camera initialization process
- The Principle and Application of Universal PCI Expansion Card
- Keil C51 programming software and user manual (full version)
- ESP32 lighting effects - light up the WS2812 colorful light strip;
- Ask about high power DCDC step-down circuit
Popular Components
Just Take a Look
Hot Downloads
- Realize online programming of 51 core microcontroller based on serial/parallel port
- Fast video segmentation algorithm
- u-boot source code
- Linux security system analysis and programming
- High Voltage VDMOSFET Breakdown Voltage Optimization Design.pdf
- Design of 2FSK Signal Generator Based on VHDL Language
- Stamping technology for coach frame components
- [Information]-JIS D2607-2008 Automotive partsVacuum brake rubber hose assemblies.pdf
- Switching Power Supply Design Books
- New features of SuperJack DG-120+Ku pole mount
MoreHot Articles
- LED chemical incompatibility test to see which chemicals LEDs can be used with
- Application of ARM9 hardware coprocessor on WinCE embedded motherboard
- What are the key points for selecting rotor flowmeter?
- LM317 high power charger circuit
- A brief analysis of Embest's application and development of embedded medical devices
- Single-phase RC protection circuit
- stm32 PVD programmable voltage monitor
- Introduction and measurement of edge trigger and level trigger of 51 single chip microcomputer
- Improved design of Linux system software shell protection technology
- What to do if the ABB robot protection device stops
京公网安备 11010802033920号